Diamond Multimedia VS50SE Installation guide

Type
Installation guide

This manual is also suitable for

Important Safety Notice
Please read the below safety instructions carefully before
installation and operation.
1. Please follow all warnings and guide lines before installation
and operation.
2. Do not expose the device to rain, moisture or liquid
3. Do not modify, open or attempt to repair the device
on your own
4. Keep the device in a ventilated area to avoid overheating.
5. Power down the HDMI source and Display before connecting
the adapters
Introduction
The Diamond VS50 HDMI to HDMI small form factor wireless
transmitter and receiver is designed to eliminate the ugly HDMI
cable from your video source to your HD wall mounted TV. Both
the sender and receiver are powered via USB port which are
readily available on your televisions and video sources such as
set top boxes, Blu-ray/DVD players and Gaming Consoles.
Slim small formfactor allows provides portability for business use
as well. The transmitter can be connected to a laptop while the
receiver can be connected to a conference room display or
projector, great for presentations and collaboration applications.
Features
• Support HDMI1.3, compatible with HDCP1.2.
• Maximum resolution up to 1080p full HD.
• 5GHz operation frequency
• Supports point to point wireless configuration.
• 30ft transmission range
Plug and play, easy installation. No drivers. No configuration needed.
Package Contents
• VS50 (Transmitter) x 1
• VS50 (Receiver) x1
• USB Type A to Micro power cable x 2
• HDMI extension cable x 2
• RT angle HDMI to HDMI converter x 1
Connector/LED Indicator Connection Diagram
Installation Requirements
1. HDMI source component (Set top box, DVD/Blu-ray, PC or
Game Console and any device with HDMI output).
2. HDMI display/projector
3. USB port for power. Note: If you do not have an available
USB port on the source or the display you can use a stand
USB wall mount charger with the included USB power cables
1. HDMI Output:Connect directly to the HDMI display or Projector
2. Wireless Status: flashes slowly when paired to the receiver.
and flashes rapidly when video/audio is being transmitted.
3. Power Input: Connect to the USB port of the display/projector.
4. Power Indicator: Remains on when powered.
Sender
Receiver
1. HDMI Input:Connect directly to your HDMI source you want to
send from.
2. Wireless Status: Remains on when the HDMI input is detected,
flashes slowly when paired to the receiver and flashes rapidly
when video/audio is being transmitted.
3. Power Input: Connect to the USB port of the source, example if
you are using a PC you may power the sender from the PC’s USB port.
4. Power Indicator: Remains on when the device is powered.
Note: This device can be powered from the HDMI port directly
without the need for the external power option. However, if you
experience any instability with connection or poor audio quality,
you will have to use the external Micro USB power connection.
1. Connect the HDMI wireless sender directly to the HDMI output of
the source. Note: use the included HDMI extension cable if
needed.
2. Connect the HDMI wireless receiver directly to the HDMI input of
the display/projector. Note: if needed use the HDMI extension
cable.
3. Connect the USB Micro cable to the power input of the receiver
and then connect the other end to the USB port on the
display/Projector. If your display/projector does not have a USB
port you can use a standard USB wall charging adapter
(Not Included).
4. Once connect with in a few seconds you should be connected
and transmitting video wirelessly from your source to the display.
Note:
Transmitting through walls, glass or other obstacles will signal
loss. For best performance place the sender and the receiver
in the same room with a clear line of sight.
Introduction
Q: The transmitter and receiver are not connecting with each other.
A: 1. Check the wireless connection status light, it should
be blinking slowly when connected.
2. Power down both the sender and receiver by
unplugging the power cable and the reconnect.
3. Make sure the sender and receiver are within 30ft clear
line of site. (no walls or cabinets)
Q: The WiFi status lights are correct but there is no signal on the display.
A: 1. Make sure the HDMI input on the display is set to the
same input on the HDMI sender.
2. Try connecting the source (Set Top Box, Blu-ray Player
and etc.) to the TV/Display directly to ensure there are
no problems with the TV or Source.
Q: Video and or Audio is unstable
A: 1. Power down both the sender and receiver by unplug-
ging the power cable and the reconnect.
2. Make sure the sender and receiver are within 30ft clear
line of site. (no walls or cabinets)
• HDMI Compliance 1.3
• HDCP Compliance HDCP 1.2
• HDMI resolutions 480p@60Hz, 576p@50Hz, 720p@50/60Hz,
1080p@50/60Hz
• Audio Format PCM
• Wireless transmission 5 GHz, up to 30ft, ≤200ms delay
Specifications
Diamond Multimedia Product Warranty
All Diamond Multimedia products are guaranteed to come with a standard one
year limited warranty. The warranty is extended only to the original buyer and is
not transferable. Some Diamond Multimedia products have an optional extended
limited warranty with registration.
It is recommended that you keep your receipt so Diamond Multimedia can verify
the purchase date of the product and confirm your warranty. For more
information, visit: http://www.diamondmm.com/diamond-multimedia-product-
warranty.html
Warranty Terms
Product Condition:
Removal and or Defacing of Serial/Part number sticker(s) on ANY Diamond
Multimedia products WILL void ALL warranties.
All products must be returned in the originally sold condition. Products
received by Diamond Multimedia for replacement that include 3rd-party
attachments will be returned to the address on the package.
All products must return in their original packaging with all original components.
There must be no physical damage to any component including damage that is caused by:
- inadequate or improper repairs carried out by any person or entity which is
not authorized by the manufacturer to perform warranty services on its behalf;
negligence, accidents, modifications,defective installation or misuse and use
of inappropriate spare parts;
- fire, immersion in liquid, lightning, earthquake, inadequate ventilation,
Acts of God,incorrect application of main voltage howsoever arising, or any
other cause beyond the control of Diamond Multimedia;
- any other goods which can be used with the product, but are not the product
itself;
- consumable or wearing items requiring replacement as part of normal
service, including (but not limited to) dry cells and rechargeable batteries.
Replacement of Product:
All Diamond Multimedia products must be sent in for RMA.
Diamond Multimedia REQUIRES the original receipt or invoice of purchase as
a copy of proof of the date of purchase.
The warranty does not transfer to third party products which Diamond
Multimedia distributes AS IS unless otherwise specified. Third party products
may be warranted by the third party.
Replacement of Diamond Multimedia RMA will follow the original products
warranty based on the original date of purchase.
Diamond Multimedia will use new or refurbished parts in performing warranty
repairs and in building replacement systems.
  • Page 1 1
  • Page 2 2

Diamond Multimedia VS50SE Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI