DAVIS Wheel-a-Weigh: Launching Wheels for Inflatables (1487) Owner's manual

Type
Owner's manual

This manual is also suitable for

DAVIS Wheel-a-Weigh: Launching Wheels for Inflatables (1487) is designed to make it easier to launch and retrieve your inflatable boat. The wheels attach to the transom of your boat and allow you to roll it on and off the trailer or launch it from the beach. The wheels are made of durable plastic and are inflated to 14 PSI. They are also equipped with nylon washers and locking pins to ensure that they stay in place.

The Wheel-a-Weigh is easy to assemble and disassemble. To assemble the wheels, simply slide the inflated tires onto the axle, insert the locking pins, and hook the struts on the transom bolts. To disassemble the wheels, simply remove the struts and pull the tires off the axle.

DAVIS Wheel-a-Weigh: Launching Wheels for Inflatables (1487) is designed to make it easier to launch and retrieve your inflatable boat. The wheels attach to the transom of your boat and allow you to roll it on and off the trailer or launch it from the beach. The wheels are made of durable plastic and are inflated to 14 PSI. They are also equipped with nylon washers and locking pins to ensure that they stay in place.

The Wheel-a-Weigh is easy to assemble and disassemble. To assemble the wheels, simply slide the inflated tires onto the axle, insert the locking pins, and hook the struts on the transom bolts. To disassemble the wheels, simply remove the struts and pull the tires off the axle.

#1487
ASSEMBLY INSTRUCTIONS
This model is designed to attach to the transom hard-
ware that exists on most hard transomed Zodiac inflat-
able boats. Hardware will be required for other boats.
The product is not to be used on boats over 300 lbs.
(136 kg).
1. Inflate tires to NO MORE THAN 14 P.S.I. (14 pounds
per square inch).
CAUTION: Gas station compressors can easily
overinflate and explode tires. Be careful not to
overinflate.
2. Slide inflated tires onto axle. Install nylon washer and
insert locking pin.
3. Hook strut on transom bolt and insert knob assembly
through hole in transom. Tighten into top threaded
insert in strut to secure.
4. Remove struts after launching. Struts can be stored
by securing to the inside of the transom using the
knob assembly tightened into the center threaded
insert in strut.
CARRYING THE BOAT
When setting the wheels to carry the boat, the knob
assemblies go through the transom from the INSIDE,
then through the struts and into the upper Nutserts.
STORING THE WHEELS
For carrying the wheels inboard after launching, the knob
assemblies go through the transom from the OUTSIDE,
then through the struts and into the center Nutserts. The
wheels rest on the hulls inside the boat in a “V.
CAUTION: This product is not designed to be towed
behind a vehicle. Damage may occur and will void
the warranty.
LAUNCHING WHEELS
FOR INFLATABLES
NOTE: This product was
discontinued in 2006.
REPLACEMENT PARTS
Part
No. Description
R1465A Tire with Innertube, 4 x 16"
(10 x 41 cm)
ONE-YEAR WARRANTY
We warrant our products to be free of defects in material
and workmanship for one year from the date of original pur-
chase. Write for full warranty details.
This warranty does not apply to product which has been
used on boats weighing more than 300 pounds (136 kg).
3465 Diablo Avenue, Hayward, CA 94545, U.S.A.
Phone (510) 732-9229 • Fax (510) 732-9188
For information about our other fine products,
visit www.davisnet.com
1487_Ins.pdf June 2008
#1487
Launching Wheels for
Inflatables
Transom hardware
Strut
07353.122
Knob
Assembly
R1487A
Tire, Innertube
and Hub
R1481B
Tire with
Innertube
R1465A
Lockpin
R1464C
Nylon
Washer
07350.163
  • Page 1 1
  • Page 2 2

DAVIS Wheel-a-Weigh: Launching Wheels for Inflatables (1487) Owner's manual

Type
Owner's manual
This manual is also suitable for

DAVIS Wheel-a-Weigh: Launching Wheels for Inflatables (1487) is designed to make it easier to launch and retrieve your inflatable boat. The wheels attach to the transom of your boat and allow you to roll it on and off the trailer or launch it from the beach. The wheels are made of durable plastic and are inflated to 14 PSI. They are also equipped with nylon washers and locking pins to ensure that they stay in place.

The Wheel-a-Weigh is easy to assemble and disassemble. To assemble the wheels, simply slide the inflated tires onto the axle, insert the locking pins, and hook the struts on the transom bolts. To disassemble the wheels, simply remove the struts and pull the tires off the axle.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI