EAZ LIFT 48800 User guide

Brand
EAZ LIFT
Model
48800
Type
User guide
WARNING: CAREFULLY READ THE FOLLOWING INSTALLATION INFORMATION.
Leveling Scissor Jacks
MODEL No. SIZE QTY
57401 20" 2
57421 24" 2
57441 28" 2
Camco Mfg., Inc.
121 Landmark Drive · Greensboro, NC 27409 · USA
Phone: 800-334-2004 · Fax: 336-668-2049
www.uscatalytic.com · [email protected]
©2007 CAMCO MFG., INC. MADE EXCLUSIVELY FOR CAMCO MFG., INC. IN CHINA
Tools for Installation
• 50'string
• C-clampsorViseGrips
™
• Electricdrill
• 1/8"drillbit
• 11/32"drillbit
• Arcwelder
(Usedonlyifweldingjackstoframe)
• 9/16"socket
• Ratchetw/extension
• LithiumGrease
• Appropriatesafetyprotection
(gloves,eyeprotection,etc.)
Ifproductcomponentsaremissing
ordamageddonotreturntodealer,
contactthemanufacturer.
1-800-334-2004 ext. 231
Installation and Operating Instructions
NOTICE
CAMCO GUARANTEE:
CamcoMfg.Inc.warrantstheoriginalpurchaserthatOlympianproductsarefreeofdefectsinmanufactureandworkmanship
foraperiodof24monthsfromthedateofconsumerpurchase.Camcowarrantycoversthereplacementofallpartsfreeofcharge.Thiswarrantydoes
notcoverdamagesresultingfrom:rust,misuse,alteration,improperinstallationorimproperoperation.Thiswarrantydoesnotcoverrepairsmadeby
unauthorizedpersonsordealers,andspecicallyexcludesliabilityforindirectorconsequentialdamagetoproperty.
For use with
all recreational
vehicles
• OlympianScissorJacksaredesignedtostabilizeandlevelrecreational
vehicles,recreationaltrailersand5thwheelrecreationaltrailers.Theyare
intendedtoreducesuspensionfreeplaywhenparked.
• DonotusetheScissorJacktoliftexcessiveweightortiresofftheground
—vehicleframeanddoorjamdamagemayresult.Useonlythestock
crankhandlesupplied.Donotuseacheaterbarhandleorimpactwrench.
• DonotusethisScissorJackforanypurposeotherthanintended.
• DonotusethisScissorJackasatirechangingjack.
CAUTION:BeforeusingthisLevelingScissorJackcontactyourRV
manufactureraboutsub-framestrength.SomeRVsmaybedesigned
andmanufacturedwithsub-framesincapableofhandlingforcebeyond
theintendedstrengthtosupportthecabinweight.CAMCO CANNOT
BE HELD RESPONSIBLE FOR ANY DAMAGES DUE TO IMPROPER USE
OR INSTALLATION OF THIS PRODUCT. CAMCO CANNOT BE HELD
ACCOUNTABLE FOR THE STRUCTURAL INTEGRITY OF ANY RV FRAME.
Other OLYMPIAN
™
Products from Camco
Stabilizing Trailer Jacks
• Extendsfrom11"to17"
• Permanenthandle
• Heavydutynoncorrosivecastaluminumbase
• Max.capacity:6000lbsperjack
• Setoftwoorfourperbox
Cross-Frame Stabilizing Jacks
Stabilizing Base Pads
O
Telescopic
Stabilizing Jacks
• Zinc-PlatedInnerTubeandScrewAssembly
• Adjustablefrom16"to30"
•QuickandEasyPullPin
• SteelConstruction-PaintedBlack
• 6000lb.LoadCapacity
•Setoftwoperbox
57461-20"x8" 57481-20"x13" 57501-24"x8"
57883
44561(Qty:2)
44560(Qty:4)
57371
57381
Adjustable Sway Control Bar
• Diminishesswayfromwindyconditionsorpassingvehicles
• Providesconstantandadjustableswayreduction
• Dualfrictionbrakepadsystem
• Secureswithsocketandspringclips
• Detachesquicklyforstorage
57521
• Cross-frameassemblyallowsforgreaterstability
• Easytofollowinstallationinstructionsprovided
• Adjustableformostcross-frameapplications(adjuststot64"to74")
• 2000lbs.staticloadcapacity
• Widepadconstructionforgreaterstability
• Installationhardwareincluded
• WorkswithmostCross-frameor"T"type
stabilizingjacks
• Anti-rattlerubbergrommetprovided
• Setoffourperbox
King Pin
5th Wheel Stabilizer
• Addgreaterstability
tothefrontofyour5thwheel
• Tripodconstructionforeasysetup
• Lockingmechanismforaddedsecurity
• Steelconstruction
• Foldsdownforeasystorage
• Chromeplatedchainprovided
57391
#207 895004
5th Wheel
Stabilizer
• Addgreaterstability
tothefrontofyour5thwheel
• Tripodconstructionforeasysetup
• Concavepadsformultipleheights
• Steeltubeconstruction
• Foldsdownforeasystorage
• Chromeplatedchainprovided
Speed Crank Handle
• 3/4"socket-endspeedwrenchdesign
• Easygriphandlewhichturnswhilecranking
• Chrome-platednish
57874
IMPORTANT!
Apply decals to the exterior of
trailer to identify the location
of each drive screw.
Step 4:
Afterdeterminingthelocation,openthejackuntilittouchestheground,usingenough
pressuresothejackwon’tmoveduringinstallation.Repeatthesestepsforalljacks
priortonalinstallation.
Step 5a: Bolt-On Installation
Before drilling make sure the drill will not damage any under
chassis components routed inside the vehicle frame such as electrical, gas,
water, generator fuel lines, holding tank plumbing, water heater, etc.
• Afterdeterminingyourlocation,usethemountingplateasatemplateandmarkthe
locationsofthefourholesonthevehicleframe.Removethescissorjack.
• Markthecenterofeachholelocationwithacenterpunchandhammer.
• Drill1/8"pilotholesandnishbydrillingholeswithan11/32"diameterdrillbit.
• Repositionjack.Usea9/16"socketandratchettoinstallthejackstothevehicle
frameusingfourboltsandfourlockwashersperjack.(Figure1)
•
Once installation is complete, apply included decals to the exterior of trailer
to identify the location of each drive screw.
Lubricatescissorlevelerscrew
withlithiumgrease.(Reapplylubricationonceayear).
Step 5b: Weld-on Installation
Before welding, make sure the weld will not damage any under
chassis components routed inside the vehicle frame such as: electrical, gas,
water, generator fuel lines, holding tank plumbing, water heater, etc.)
• Beforewelding,makesureyoufollowallweldermanufacturersafetyprecautions.
• Afterdeterminingyourlocation,weldeachmountingplatetothevehicleframewith
four1"longwelds,asshown.(Figure2)
•
Once installation is complete, apply included decals to the exterior of trailer
to identify the location of each drive screw.
Lubricatescissorlevelerscrew
withlithiumgrease.(Reapplylubricationonceayear).
For recreational trailer or 5th wheel:
Step 1a:
Park on Level Ground. Check ground clearance.
Chock all tires.
Step 2a:
Draw a string from the front corner of the trailer
frame (A), back to the bottom of the front tire.
Do the same from the rear to the rear tire as
illustrated below (B).
(Any objects extending beyond these lines
could be damaged, dragged off or destroyed
in uneven terrain, entering or exiting drive-
ways, driving off road, etc.)
For motorhome:
Step 1b:
Park your Motorhome on level ground.
Check ground clearance. Chock all tires and
apply emergency brake.
Step 2b:
Draw a string from the front bumper, back to
the bottom of the front tire. Do the same from
the rear bumper (or overhang) to the rear tire as
illustrated below. (Any objects hanging over
these lines could be damaged, dragged off
or destroyed in uneven terrain, entering or
exiting driveways, driving off road, etc.)
• Thereissufcientgroundclearance.
• Alljackhandlereceiverswillbeaccessible
• Thereisampleclearancefromotherunder-chassiscomponents.
When selecting mounting placement, be sure:
CAUTION:Wearappropriatesafetyequipmentduringinstallation:eyeprotection,gloves,weldingclothes,etc.
Step 3: Select the location of each scissor jack along the frame.
• Placeeachjacknearesttoeitherendoftheframe(frontorback)withoutgoingoutsideof
thestrings.HoldfullycollapsedjackinplacewithC-clampsorViseGrips.Makesurehandle
receivers are facing outward, but not extending out past side of trailer.
• Openandcloseusingthejackhandletoensurethereisnocontactwithorobstructionofany
under chassis components such as plumbing or exhaust, etc.
• Movethejackasneededtondthebestlocation.
Figure 1
Figure 2
Step 1:
ParkRVonlevelgroundandpreventwheelsfromrollingusingemergencybrakeandtirechocks.
Step 2:
LevelRVfrontandbackusingtonguejackorlandinggear.
Step 3:
Crankscissorjack(s)(onlowestsideofvehicle)downrsttogetlevel.Usejacksonoppositesidetostabilize.
Do not use the scissor jack to lift excessive weight or tires off the
ground – vehicle frame and door jam damage may result.
•Useonlythestockhandlesupplied.
•Donotuseacheaterbarhandleorimpactwrench.
•Donotusethisscissorjackforanypurposeotherthanintended.
•Donotusethisscissorjackasatirechangingjack.
FINDING THE CORRECT LOCATION FOR MOUNTING
INSTALLATION
OPERATING PROCEDURES
INSTALLATION
  • Page 1 1
  • Page 2 2

EAZ LIFT 48800 User guide

Brand
EAZ LIFT
Model
48800
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents