Axminster CSC500K User manual

Axminster
Brand
Axminster
Model
CSC500K
Category
Power sanders
Type
User manual

Axminster CSC500K Key Operated Woodturning Chuck Set is engineered and manufactured to the highest quality standards. This product is an essential accessory to your workshop and is ideal for a wide range of woodturning projects.

The chuck set includes a 65mm Barracuda chuck, 4 gripper jaws, a tightening key, a set of 4 extended pin jaws, a set of 4 step jaws, a set of 4 internal & external gripper jaws, a screw chuck, and a 3/4" x 16tpi adaptor. This chuck set has a gripping capacity of 7/8" to 3-1/4" and can be used for both inside and outside gripping.

The chuck is easy to install and operate. Simply select the appropriate jaw for your project, place it on top of the carrier, and tighten it down with the provided hex wrench. The chuck can then be mounted to your lathe using the included adaptor.

Axminster CSC500K Key Operated Woodturning Chuck Set is engineered and manufactured to the highest quality standards. This product is an essential accessory to your workshop and is ideal for a wide range of woodturning projects.

The chuck set includes a 65mm Barracuda chuck, 4 gripper jaws, a tightening key, a set of 4 extended pin jaws, a set of 4 step jaws, a set of 4 internal & external gripper jaws, a screw chuck, and a 3/4" x 16tpi adaptor. This chuck set has a gripping capacity of 7/8" to 3-1/4" and can be used for both inside and outside gripping.

The chuck is easy to install and operate. Simply select the appropriate jaw for your project, place it on top of the carrier, and tighten it down with the provided hex wrench. The chuck can then be mounted to your lathe using the included adaptor.

210307
CSC500K
Key Operated
Woodturning
Chuck Set
Axminster Reference No: CSC500K
User Manual
www.axminster.co.uk
01
Index of Contents...
www.axminster.co.uk
Page No.
Safety Protection Symbols
SAFETY!!
!
The symbols shown on the cover of this
manual advise that you wear the correct
safety protection when using this machine.
E
y
e
P
r
o
t
e
c
t
i
o
n
S
a
f
e
t
y
H
e
l
m
e
t
P
r
o
t
e
c
t
i
v
e
G
l
o
v
e
s
S
a
f
e
t
y
F
o
o
t
w
e
a
r
R
e
s
p
i
r
a
t
o
r
S
a
f
e
t
y
V
i
s
o
r
R
e
a
d
M
a
n
u
a
l
T
w
o
M
a
n
A
s
s
e
m
b
l
y
E
a
r
D
e
f
e
n
d
e
r
s
D
u
s
t
M
a
s
k
Warranty...
Thank you for purchasing one of Axminster’s growing family of woodworking products. The
CSC500K Chuck Set is engineered and manufactured to the highest quality standards. You
will find this product an essential accessory to your workshop.
This product is warranted against defects in material and workmanship for a period of one
years for all components. This warranty applies to the original purchaser of the product and
is limited to the repair and/or replacement of the product, or its parts at the discretion of
Axminster Power Tool Centre. Excluded are parts which have been misused, abused, altered,
or consumed by normal operation of the chuck. Also excluded are direct or consequential
damages to persons, or properties, or materials is as proof of purchase and must be
referenced to authorize any warranty repair. Call your Axminster dealer for proper
authorization.
Index of Contents......................................................................................................................................... 1
Warranty........................................................................................................................................................1
Safety Instructions for Chuck Systems....................................................................................................... 2
What’s in the Box.....................................…………...................................................................................2-3
Chuck System Description..........................................................................................................4
Jaw Capacity Chart..................................................................................................................... 5
Installing Jaws to Chuck............................................................................................................. 5
Mounting the Adaptor..................................................................................................................5
Mounting the Chuck to Your Lathe............................................................................................. 6
Operating the chuck....................................................................................................................6
Chuck Gripping Depth.................................................................................................................6
Lathe Speeds...............................................................................................................................6
Maintenance................................................................................................................................ 6
02
Safety Instructions for Chuck Systems...
The following suggestions will enable you to observe good working
practices, keep yourself and fellow workers safe and maintain your
tools and equipment in good working order.
Good Working Practices/Safety
WARNING!!
!
KEEP TOOLS AND EQUIPMENT OUT
OF THE REACH OF YOUNG CHILDREN
1. Do not wear gloves or loose clothing when turning.
2. Do not wrap any strip sandpaper or clothing around your hands or fingers when
sanding or turning.
3. Use proper eye protection when turning.
4. Check your wood for splits, weakness or cracking prior to mounting on the
chuck.
5. Confirm that the wood is tightly gripped before turning your chuck under power.
6. Rotate the chuck manually prior to starting your lathe to confirm proper
clearance.
7. Always check and re-lighten after any problem or catch.
8. Use appropriate speeds as referenced in instructions.
9. Always turn with sharp lathe chisels.
10. Capture fine particles from the air with a dust collector.
11. Keep clean and lubricate with a light coat of oil.
What’s in the Box...
Model Number: (210307) CSC500K
A CSC500K 65mm Barracuda chuck (pre-threaded for 1" x 8tpi)
B 1 Set (4 pieces) gripper jaws (shipped pre-mounted to chuck)
C 1. Hex wrench
D 1 Tightening Key
E 1 Set( 4 piece) extended pin jaws
F 1 Set (4 piece) step jaws
G 1 Set (4 piece) internal & external gripper jaws
H 1 Screw chuck
H 1 3/4" x 16tpi adaptor
Instruction Manual
A
D
E F
H
I
G
B
C
03
What’s in the Box...
www.axminster.co.uk
04
Chuck System Description...
FREEPHONE 0800 371822
A. Main body: designed to hold all jaws as an assembly.
B. Carrier: to which the top jaws are each attached with one or two hex screws. ( the jaws
has a tongue which must mate with grooves)
C.Jaws: attached to the carrier, used for gripping the wood piece to be turned.
D. Socket hex screws: attach jaws to chuck (2 per jaw/1 per pin jaw).
E. Tightening holes: insert and turn the tightening key to secure grip.
A
B
C
D
E
(Shown with two round jaws installed)
05
Jaw Capacity Chart...
www.axminster.co.uk
Installing Jaws to Chuck...
Mounting the Adaptor...
Select the appropriate jaw for your project. Place the selected jaw on top of the carrier,
matching the number stamped on the main body to the number on each individual jaw. Using
the provided hex wrench, firmly tighten the jaw down onto the surface of the carrier with the
hex screws. Repeat this step for the remaining three jaws.
1. Wipe the inside of the threads and the outside of the adaptor to insure both surfaces are
clean.
2. Use the furnished 3/4" x l6tpi adaptor if necessary.
3. Hold the chuck in your hand, screw and tighten the adaptor into the bottom threaded
portion of the chuck.
Adaptor
Chuck
1 Set (4 pieces) gripper jaws
1 Set (4 piece) Internal &
external gripper jaws
1 Set (4 piece) step jaws
1 Set( 4 piece) extended pin
jaws
7/8" to 1-1/2"
1-3/8" to 2"
1/4" to 1"
7/8" to 1-5/8"
2-1/4" to 2-7/8"
2-5/8" to 3-1/4"
1/16" to 13/16"
Step 1: 5/8" to 1-5/16"
Step 2: 1-3/16" to 1-7/8"
B
E
F
G
Jaws Style
Gripping Dowel
Outside Diameter
Gripping in Hole
Inside Diameter
Brushing is all that is needed to clean your chuck. If the chuck becomes sticky, clean with
“Dry PTFE Spray Part No: 810135” or “Camellia Oil Part No: 510018”.
DO NOT allow wood chips to become compacted in the teeth of the gear
mechanism.
CAUTION: Gear mechanism should be cleaned in between uses. Excessively dirty
gear teeth may lead to mechanical failure.
06
Mounting the Chuck to Your Lathe...
Screw the completed assembly onto your lathe. The chuck should go on effortlessly with no
binding. Screw the chuck all the way until the adapto r face contacts the shoulder of the
lathe spindle. Lock the spindle, slightly unscrew the chuck and give it a firm spin. This will
snap the chuck firmly in place.
The tightening key aligns with a pivot hole inside your chuck. The tightening key has gear
teeth which index with the scroll mechanism inside the micro key chuck. Clockwise
tightens, counter-clockwise loosens the jaws.
When turning a bowl, for safety reasons, allow a minimum
amount of wood for the chuck to grab while turning.
1. Cavity base (inside grip) - for a 2" diameter base,
minimum hole depth is 3/16".
2. Spigot base (outside grip) - for a 2" diameter base
minimum grip is 3/16".
Turning: 500-I500rpm
Sanding & Polishing: 1500-2500rpm
Make sure your wood is properly aligned and balanced
when mounted or re-mounted.
Use slower speeds for larger work.
Operating the Chuck...
Chuck Gripping Depth...
Lathe Speeds...
Maintenance...
!
!
210307
www.axminster.co.uk
Axminster Devon EX13 5PH UK
FREEPHONE 0800 371822
Axminster Reference No: CSC500K
CSC500K Key Operated Woodturning Chuck Set
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Axminster CSC500K User manual

Axminster
Brand
Axminster
Model
CSC500K
Category
Power sanders
Type
User manual

Axminster CSC500K Key Operated Woodturning Chuck Set is engineered and manufactured to the highest quality standards. This product is an essential accessory to your workshop and is ideal for a wide range of woodturning projects.

The chuck set includes a 65mm Barracuda chuck, 4 gripper jaws, a tightening key, a set of 4 extended pin jaws, a set of 4 step jaws, a set of 4 internal & external gripper jaws, a screw chuck, and a 3/4" x 16tpi adaptor. This chuck set has a gripping capacity of 7/8" to 3-1/4" and can be used for both inside and outside gripping.

The chuck is easy to install and operate. Simply select the appropriate jaw for your project, place it on top of the carrier, and tighten it down with the provided hex wrench. The chuck can then be mounted to your lathe using the included adaptor.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents