®
Page 1
ALLURE™ WS1 SERIES
RANGE HOOD
!
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer at the address or telephone
number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service panel and
lock the service disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting means can-
not be locked, securely fasten a prominent warning device, such as a
tag, to the service panel.
3. Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards, in-
cluding fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent
backdrafting. Follow the heating equipment manufacturer’s guideline
and safety standards such as those published by the National Fire
Protection Association (NFPA), and the American Society of Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local
code authorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical
wiring and other hidden utilities.
6. To reduce the risk of fire or electric shock, do not use this range hood
with an additional speed control device.
7. Ducted fans must always be vented to the outdoors.
8. To reduce the risk of fire, use only metal ductwork.
9. Use with approved cord-connection kit only.
10.This unit must be grounded.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1. Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
2. Always turn hood ON when cooking at high heat or when cooking
flaming foods.
3. Clean ventilating fans frequently. Grease should not be allowed to
accumulate on fan or filter.
4. Use proper pan size. Always use cookware appropriate for the size
of the surface element.
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:*
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels - violent
steam explosion will result.
4. Use an extinguisher ONLY if:
A. You know you have a Class ABC extinguisher and you already
know how to operate it.
B. The fire is small and contained in the area where it started.
C. The fire department is being called.
D. You can fight the fire with your back to an exit.
* Based on “Kitchen Fire Safety Tips” published by NFPA.
ALLURE
™
WS1 SERIES
RANGE HOODS
READ AND SAVE THESE INSTRUCTIONS
Installer: Leave this manual with
the homeowner.
Homeowner: Operating and
Cleaning information on page 5.
Page 1
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
2. To avoid motor bearing damage and noisy and/or unbalanced impel-
lers, keep drywall spray, construction dust, etc. off power unit.
3. For best capture of cooking impurities, your range hood should be
mounted so that the top of the hood is 24-30” above the cooking
surface.
4. Please read specification label on product for further information and
requirements.
TABLE OF CONTENTS
This manual is divided into sections as follows:
• “PREPARE HOOD LOCATION”
Run ductwork from roof or wall cap, and electrical wiring from
service panel - to installation location
• “PREPARE THE HOOD”
Get your hood ready for installation
• “CONNECT WIRING”
Make electrical wiring connections to hood
• “INSTALL HOOD”
Secure hood to cabinet and ductwork - install bulbs and filters
• “OPERATION”
How to use the hood controls
• “CLEANING”
Keep your hood in top working condition
• “SERVICE PARTS”
Part numbers and exploded view of hood components
• “WARRANTY”
One-year limited warranty and how to contact us
NOTE If hood is to be installed Non-Ducted:
• Purchase a set of (2) non-ducted filters from your
local distributor or retailer and attach them to the
aluminum mesh filters.
Patent No.:
US D450, 829 S
!
FOR DOMESTIC COOKING ONLY
!
®
Page 2
ALLURE™ WS1 SERIES
RANGE HOOD
CABINET
BOTTOM
CABINET FRONT
HORIZONTAL DUCT
ACCESS HOLE
5¼"
5¼"
7½"
1
/
8
"
¾"
13
15
/
16
" (30" hood)
16
15
/
16
" (36" hood)
13
15
/
16
" (30" hood)
HOOD
MOUNTING
SCREWS (4)
ELECTRICAL
ACCESS HOLE
(in wall)
3¾"
16
15
/
16
" (36" hood)
CENTER
LINE
WOOD SHIMS
(recessed-bottom
cabinets only)
19
15
/
16
" (42" hood)
19
15
/
16
" (42" hood)
SOFFIT
24" - 30" ABOVE
COOKING SURFACE
CABINET
3¼" X 10" DUCT
(For horizontal discharge)
WALL CAP
ROOF CAP
3¼" X 10"
(For vertical
discharge)
HOUSE WIRING
(Top or Back of hood)
HOOD
HOOD
HOOD
PREPARE HOOD LOCATION
PREPARE THE HOOD
1 Remove 7” Round Duct Plate from top of hood. Set duct
plate aside - with mounting screws.
2 Remove tape holding Filters in place. Pull down on filter
tabs and lift filters out. Set filters aside.
7” ROUND
DUCT PLATE
FILTERS
1 Determine whether hood will discharge vertically (3¼” x 10”
or 7” Round), horizontally (3¼” x 10” only) or non-ducted. For
vertical or horizontal discharge, run ductwork between the
hood location and a roof cap or wall cap. For best results, use
a minimum number of transitons and elbows.
2 Use diagrams, below, for proper placement of ductwork and
electrical cutout in cabinet or wall. For a non-ducted installa-
tion, DO NOT cut a duct access hole.
3 Run house wiring between service panel and hood location.
VERTICAL DUCT
ACCESS HOLE
1¼"
1½"
10½"
5¼"
5¼"
CENTER
LINE
HOOD MOUNTING SCREWS (4)
ELECTRICAL
ACCESS HOLE
(in cabinet bottom)
WOOD SHIMS
(recessed-bottom
cabinets only)
CABINET FRONT
CABINET BOTTOM
13
15
/
16
" (30" hood)
16
15
/
16
" (36" hood)
7½"
5"
2"
19
15
/
16
" (42" hood)
13
15
/
16
" (30" hood)
16
15
/
16
" (36" hood)
19
15
/
16
" (42" hood)
PREPARE HOOD LOCATION
3¼” X 10”
VERTICAL DUCTING
7” ROUND
VERTICAL DUCTING
3¼” X 10”
HORIZONTAL DUCTING
3¼” x 10” or
7” ROUND DUCT
(For vertical discharge)
®
Page 3
ALLURE™ WS1 SERIES
RANGE HOOD
PREPARE THE HOOD PREPARE THE HOOD
3 Remove
Damper/Duct
Connector from
inside the hood.
Set connector
aside - with
mounting
screws and
parts bag.
4 Remove
Wiring Cover
from inside the
hood. Set
cover and
mounting
screw aside.
5 Remove either
top or back
wiring knockout
and install
approved
Electrical Cable
Clamp.
DAMPER/DUCT
CONNECTOR
WIRING
COVER
ELECTRICAL CABLE CLAMP
Non-Ducted Installation - Skip to “Connect
Wiring” section.
6 Remove Light Panel - held in place with (3) #8 screws and
(2) #8 screws. Disconnect light assembly wire harness
(white connector).
(3) #8 SCREWS
LIGHT
PANEL
(2) #8 SCREWS
The following
Steps (6 thru
13) are for
DUCTED
INSTALLATION
ONLY.
➙
➙
BAFFLE
7 Remove Air
Chute - held in
place with one
(1) screw.
NOTE: Be
careful not to
disconnect any
wires.
9 Rotate baffle.
Reinsert baffle into
air chute (as
shown) so that
baffle
tabs fit all the
way into
slots in air
chute. An audible
“click” will be heard
when fully installed.
This will close off
the air flow through
the non-ducted
slots on top of
hood.
10
Re-install air chute, re-connect wire
harness, and replace light panel.
NOTE: Be careful not to trap wires
between
support fin and light panel.
AIR CHUTE
SLOTS
➙
➙
8 Remove Baffle
from air chute.
➙
BAFFLE
SUPPORT FIN
TABS
®
Page 4
ALLURE™ WS1 SERIES
RANGE HOOD
CONNECT WIRING
WARNING: To reduce the risk of electric shock,
make sure power is switched off at the service
panel. Lock or tag service panel to prevent power
from being switched on accidentally.
HOUSE
WIRING
(120 VAC)
CARDBOARD
(Use to protect
cooktop)
1 Connect House Wiring (120 VAC) to hood. Use a piece of
Cardboard to protect the cooktop, if necessary.
2 Connect house black to hood black wire, house white to
hood white wire, and house ground under
Green Ground
Screw. Securely tighten cable clamp onto house wiring.
GREEN
GROUND
SCREW
3 Replace wiring cover.
PREPARE THE HOOD
11 Remove appropriate Duct Knockout(s) from top or back of
hood.
REAR
RECTANGULAR
DUCT KNOCKOUT
(Remove for 3¼” x 10”
Horizontal Discharge)
TOP RECTANGULAR
DUCT KNOCKOUT
(Remove for 3¼” x 10”
Vertical & for 7” Round
Discharge)
SEMI-CIRCULAR
DUCT KNOCKOUT
(Remove for 7” Round
Discharge)
13
7” Round Ducted Discharge Only: Re-install 7” Round Duct
Plate removed in Step #1 under “PREPARE THE HOOD”
section. Install a 7” round damper (purchase separately).
Damper flap must open freely in direction of air flow (away
from range hood).
12
3¼” x 10” Ducted Discharge Only: Attach Damper/Duct
Connector over knockout opening. Make sure damper Pivot
is nearest to
Top/Back Edge of hood. Remove Tape from
damper flap.
DAMPER/DUCT
CONNECTOR
(Vertical discharge
position shown)
TAPE
UP TO 1”
SIDE-TO-SIDE
ADJUSTMENT
PIVOT
TOP/BACK
EDGE
NOTE
To accomodate off-center ductwork, the Damper/Duct
Connector can be installed up to 1-inch on either side
of hood center or the 7” Round Duct Plate can be installed up to ½”
on either side of hood center. In extreme off-center installations,
one end of the duct connector may need to be trimmed to clear the
electrical cable clamp.
➙
➙
®
Page 5
ALLURE™ WS1 SERIES
RANGE HOOD
WARNING: To reduce the risk of electric shock,
disconnect from power supply before cleaning.
Aluminum mesh filters: Clean frequently using hot water and a
mild detergent. Filters are dishwasher safe.
Charcoal filters: Clean filter surfaces frequently with a damp cloth
and a mild detergent. DO NOT immerse filters in water or put in
dishwasher. The special “Clean Sense” feature indicates when
the filter is to be replaced. The blue and yellow strips will blend to
green when it is time to change the filter. The “Clean Sense” fea-
ture works best when facing toward the cooking surface.
To clean hood: Remove filters. Use a damp cloth and a mild deter-
gent to wipe all grease-laden surfaces. Use care when cleaning
fan blade - it must not become bent or misaligned. DO NOT AL-
LOW WATER TO ENTER MOTOR. Make sure all surfaces are
completely dry before re-installing filters and restoring power.
Motor is permanently lubricated. Do not oil or disassemble motor.
OPERATION
CLEANING
Fan: The 3-position rocker switch (on the left) controls the fan. The
left position is low speed, center position is off, and right position is
high speed. An indicator light shows that the fan is on.
Light: The 3-position rocker switch (on the right) controls the lights.
The left position is low light intensity, center position is off, and
right position is high light intensity.
INSTALL HOOD
KEYHOLE
(4)
MOUNTING
SCREW
(4)
1 Hang hood from (4) Mounting Screws (from parts bag). Slide
hood towards wall until mounting screws are engaged in
narrow end of (4)
Keyholes. Tighten mounting screws
securely.
PAR20,
50W MAX.
HALOGEN
BULB (2)
- or -
R16,
40W MAX.
INCANDESCENT
BULB (2)
4 Replace filters and make sure fan blade turns freely. Turn on
power at service panel, and test for proper operation.
2 Connect ductwork to hood. Use Duct Tape to make joints
secure and air tight.
DUCT
TAPE
CAUTION DO NOT PUSH ON FAN BLADE. Pushing on the
blade may cause it to interfere with other hood parts.
3 Install (2) PAR20, 50 W Maximum Halogen Bulbs or (2) R16,
40 W Maximum
Incandescent Bulbs. Purchase bulbs
separately.
!
CAUTION: Bulbs may be hot! Refer to bulb packaging
for further information.
If hood is to be installed Non-Ducted:
Purchase a set of (2) non-ducted filters from your local distributor
or retailer and attach them to the aluminum mesh filters.
NON-DUCTED FILTERS
®
Page 6
ALLURE™ WS1 SERIES
RANGE HOOD
626976B
WARRANTY
NUTONE ONE YEAR LIMITED WARRANTY
NuTone warrants to the original consumer purchaser of its products that such products
will be free from defects in materials or workmanship for a period of one year from the
date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
During this one-year period, NuTone will, at its option, repair or replace, without charge,
any product or part which is found to be defective under normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS
AND TUBES. This warranty does not cover (a) normal maintenance and service or (b)
any products or parts which have been subject to misuse, negligence, accident, improper
maintenance or repair (other than by NuTone), faulty installation or installation contrary
to recommended installation instructions.
The duration of an implied warranty is limited to the one-year period as specified for the
express warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above limitation may not apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OPTION,
SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSE-
QUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION
WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclu-
sion or limitation of incidental or consequential damages, so the above limitation may not
apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state. This warranty supersedes all prior warranties.
To qualify for warranty service, you must (a) notify NuTone at the address or telephone
number below, (b) give the model number and part identification and (c) describe the
nature of any defect in the product or part. At the time of requesting warranty service, you
must present evidence of the original purchase date.
NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
SERVICE PARTS
KEY NO. PART NO. DESCRIPTION
1 R680508 7” Round Duct Plate (includes hardware)
2 R740013 Damper/Duct Connector
(includes hardware)
3 R602017 Screw, #8-18 x ¼ Hex* (2 in package)
4 R561115 Rocker Switch, Almond (2 in package)
R561116 Rocker Switch, White (2 in package)
R561117 Rocker Switch, Black (2 in package)
R561119 Rocker Switch, Biscuit (2 in package)
5 R627518 Nameplate, White
R627519 Nameplate, Almond
R627520 Nameplate, Stainless
R627533 Nameplate, Biscuit
R627579 Nameplate, Black
6 R607657 Lens
7 R602534 Screw, 8-18 x 3/8* (2 in package)
8 R602533 Ground Screw (2 req.)
9 R680504 Wiring Cover (includes hardware)
10 * Rivet, Pop .125 dia.
11 R169016 Filter Spring Kit
12 R169002 Motor Mounting Screw (3 each part)
13 R99080535 Motor (includes Motor Mounting Kit)
14 R401647 Air Chute Assembly
(includes Key No. 15 & hardware)
15 R401646 Baffle
16 R531075 Fan Blade (Includes hairpin clip)
** R99420635 Hairpin Clip
17 99010299 Filter Kit, for 30” Hood (2 per bag)
99010300 Filter Kit, for 36” Hood (2 per bag)
99010301 Filter Kit, for 42” Hood (2 per bag)
18 R111630 Lamp Socket Harness
19 R7201621 Light Panel, White, for 30” Hood
R7201651 Light Panel, White, for 36” Hood
R7201671 Light Panel, White, for 42” Hood
R7201622 Light Panel, Almond, for 30” Hood
R7201652 Light Panel, Almond, for 36” Hood
R7201672 Light Panel, Almond, for 42” Hood
R7201624 Light Panel, Black, for 30” Hood
R7201654 Light Panel, Black, for 36” Hood
R7201674 Light Panel, Black, for 42” Hood
R720163 Light Panel, Stainless, for 30” Hood
R720166 Light Panel, Stainless, for 36” Hood
R720168 Light Panel, Stainless, for 42” Hood
R7201625 Light Panel, Biscuit, for 30” Hood
R7201655 Light Panel, Biscuit, for 36” Hood
R7201675 Light Panel, Biscuit, for 42” Hood
20 R169004 Indicator Light (includes 2 wire nuts and lens)
** R169010 Light Diode Assembly (includes wire nut)
** R111626 Wire Harness
** 99010308 Non-Ducted Filter Kit, 30” (2 per bag)
** 99010309 Non-Ducted Filter Kit, 36” (2 per bag)
** 99010310 Non-Ducted Filter Kit, 42” (2 per bag)
Order replacement parts by PART NO. - not by KEY NO.
* Standard hardware - may be purchased locally.
** Not illustrated.
1
2
3
5
6
9
10
11
13
14
8
4
16
17
3
18
7
19
3
12
20
7
7
15
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- español: NuTone WS1 Manual de usuario
Related papers
-
NuTone WS1 SERIES User manual
-
Broan WS130WW Installation guide
-
NuTone WS130SS User manual
-
NuTone WS136WW User manual
-
-
-
-
-
-
Other documents
-
Whirlpool RH2030XJB3 User manual
-
Whirlpool RH2636XJQ3 User manual
-
-
-
-
-
-
-
Broan ALLURE QS1 SERIES Instructions Manual
-
Broan QS342SS User manual