Audio Design Pro Trio Club User manual

Brand
Audio Design Pro
Model
Trio Club
Category
Audio mixers
Type
User manual

This manual is also suitable for

PROFESSIONAL SPEAKERS, AMPLIFIERS AND ACCESSORIES
Via dell’industria, 28 - 42025 CAVRIAGO (RE)
+39 0522 941444 - Fax +39 0522 942363
www.audiodesign-pro.com
[email protected]
Audiodesign Srl
TRIO SESSION
TRIO MASTER
OTHER SYSTEMS OF THE TRIO FAMILY
Subwoofer 12” - 320 mm - VC 65 mm
Satellites 2 x 8” - 200 mm - VC 50 mm
Horn Compression Tweeter - VC 34 mm
Power Max/RMS: 1280 / 640 W
SPL Max: 124 dB
Subwoofer 15” - 380 mm - VC 75 mm
Satellites 2 x 10” - 250 mm - VC 50 mm
Horn Compression Tweeter - VC 44 mm
Power Max/RMS: 1440 / 720 W
SPL Max: 127 dB
TRIO CLUB
User Manual
Full Range Sound System
- 7 -
Portable Full Range Sound System TRIO CLUB
Introduction
Thank you for purchasing an AudioDesign TRIO Active Sound system.
TRIO series is designed to provide an high and powerful sound quality in a compact size.
The main features are:
*
Active subwoofer cabinet with additional amplifiers for the passive satellites.
*
High sensitivity passive satellites.
*
High and precise acoustic quality also with high power.
The final result is a full, detailed and powerful sound.
*
Portability: the system is easy fit and portable by one person.
- 2 -
Application
The KPRO systems are a professional solution for every DJ or Live events where high pressure and extreme
sound quality is required.
Precautions:
Caution: When using any electric product , precautions should always be taken, including the following:
1) Read carefully all instructions before using the product.
2) To reduce the risk, strict supervision is necessary when the product is used near children.
3) Don't use the product near to water sources like sinks, kitchens, wet floors, pools,
or similar or when raining.
4) In case hearing losses or buzzing occur, please contact a doctor.
5) This products should be located so that its position does not interfere or reduce its proper ventilation.
6) This product should be site away from heat sources such as radiators or any other product that
generate heat.
7) This product should be connected to a power supply line only of the type described on the operating
instructions. Check always the status of the power cable.
8) In case you need to replace the fuse, unplug power supply before replacement. The fuse is located
over the power socket and needs to be replaced with a fuse of same type and value. If the fuse blows again,
please contact our service. DON'T replace it a second time with a higher value fuse.
9) Unplug power supply when left unused for a long period of time. Don't draw the cable but pull out the
plug.
10) Make sure that power switch can always be easily reached.
11) The product needs to be inspected by authorized or qualified personnel in case:
A- The power cable or plug are damaged
B- Objects or liquids fall inside the product
C- The product has been exposed to rain
D- The product doesn't appear to operate normally or exhibits a marked change in performance.
E- The product has fallen and been damaged.
12) DON'T operate on the product, except indications on the user's manual . Please refer to authorized
and qualified personnel for any other operation.
13) Caution: Don't place objects on the product's power cable or place it in a position where it could be
damaged or cause interferences. Improper installation could cause fire risk and/or personal injury.
Service
All Audio Design PRO products have been inspected and tested before leaving the factory and , if properly
used, they will work for many years. However, in case of any problem, please proceed in the following way:
Contact your dealer and inform about the defect you found
In case it won't be possible to solve the problem with the dealer, the product needs to be returned, preferably
in its original packaging or in a proper packing to protect it during the transport. Purchase documents must
be produced too.
Your dealer will arrange the shipment to our service centre.
Conformity:
Audiodesign Pro products comply with presently existing directives and standards.
TRIO
BY MEANS OF OUR ACCESSORIES, DIFFERENT CONFIGURATIONS OF THE SYSTEM ARE POSSIBLE
SATELLITE STAGE PRO 65
INPUT
SATELLITES INPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
SPEAKERS
High Sensitivity Woofer
1 x 6.5”
(165 mm)
Dome Tweeter
VC 30 mm
VC 32 mm
MAIN FEATURES
TOTAL IMPEDANCE :
4 Ohm
TOTAL POWER :
160 W RMS
(250 W Max) with X-over 200 Hz 18 dB/oct
TOTAL SPL Max:
121 dB
Frequency Response:
100 ÷ 20000 Hz
( )± 3 dB
WEIGHT & SIZES Weight Satellite:
4 kg
Size (WxLxH) cm:
20 x 19 x 27
Tweeter :Crossover
6000 Hz
12 dB/oct
Passive
TECHNICAL SPECIFICATIONS
SUBWOOFER STAGE PRO W10
INPUT
OUTPUT
SATELLITES OUTPUT: Speakon NL4 (pin 1+ = +, pin 1- = -)
AMPLIFIERS Subwoofer Power Output: 250 W RMS (500 W Max)
Satellites Power Outputi: 2x125 W RMS (2x250 W Max)
SPEAKER
Subwoofer: 1 x 10”
(250 mm)
Frequency Response: 30 ÷ 260 Hz (± 3 dB)
SPL Max:
123 dB
WEIGHT & SIZES Weight Subwoofer:
32 kg
Sizes (WxLxH) cm:
43 x 39 x 39
VC 50 mm
@ 4 Ohm Load
LINE IN: Combo Socket XLR 3-F / Jack Stereo
INPUT: Balanced and Unbalanced
Electronic Crossover HP Satellites:
Frequency 38
- 250 Hz / 12 dB/Oct.
Electronic Crossover LP Subwoofer:
Frequency
46 - 240 Hz / 12 dB/Oct.
SPL Max:
121 dB
Portable Full Range Sound System TRIO CLUB
- 6 -
10
- 3 -
11
13
12
L
R
LOW PASS
-15 +15
0 10
HI PASS
GAIN
PEAK
-15 +15
0 10
GAIN
HI PASS
PEAK
LEFT speaker R IGHT speaker
0 10
GAIN
PEAK
50
260
80
120
60
Hz
PHASE
SHIFT
0 - 180°
Subwoofer
50
260
80
120
60
Hz
50
260
80
120
60
Hz
HIGH
PEAK
HIGH
3
1
2
4
7
6
58 5
6
7
8
POWER
9
OUT+:1+/
OUT- :1-
OUTPUT
LEFT RIGHT
SPEAKER OUTPUT:
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
LEFT(Mono)
RIGHT
ST
MONO
LINE IN
USE ONLY WITH 250V FUSE
220
18
AUDIODESIGN PRO: TRIO CLUB
Sensitivity Magnitude
dB SPL/watt (4 ohm load)
-
log Frequency - Hz
MLSSA: Frequency Domain
M
L
S
S
A
10000.01000.0100.020.0
auto
45.0
50.0
55.0
60.0
65.0
70.0
75.0
80.0
85.0
90.0
95.0
Portable Full Range Sound System TRIO CLUB Portable Full Range Sound System TRIO CLUB
Satellites Volume setting
6
6
Switch power on and begin to turn clockwise the satellite GAIN knobs until the correspondent PEAK led begins
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Now listen to the satellites with this output level; if you detect distorsion or saturation of the signal (i.e of microphone) check
the possibility of reducing the level of the signal concerned at his source, otherwise try to slightly lower the mixer’s main
otput. Should this not be enough, reduce the satellites volume until you have an optimal sound.
Sub Volume setting
3
Volume setting of the system is made by means of the three LEVEL
knobs on top of the subwoofer:
- Left satellite is GAIN LEFT
- Right satellite is GAIN RIGHT
- Subwoofer is GAIN SUBWOOFER
Before switching power on and proceed to system setting, make sure that
all three knobs are completely turned counterclockwise, at level 0, and that the mixer output is set so that the peaks level
Set first the satellites volume alone and then the subwoofer volume alone.
After having memorized the knobs setting LEFT e RIGHT, take them back to 0 and begin now to turn clockwise the
SUBWOOFER GAIN knob until the correspondent PEAK led begins to flash shortly for less than 1 second.
This is the optimal level being connected to a mixer sending to MAIN a signal with level peaks within 0 and +3dB.
Now listen to the Sub with this output level; if you detect distorsion of basses, turn slightly the knob back counterclokwise.
Final system setting
Bring the three knobs at the optimal level you have checked and listen to the complete system, again at the mixer
main level peaks between 0 and +3 dB.
If you detect to much basses compared with satellites output, turn slightly back the SUB LEVEL knob.
If you detect instead not enough basses, turn slightly back the setellites LEVEL LEFT and RIGHT knobs.
L
R
LOW PASS
-15 +15
0 10
HI PASS
GAIN
PEAK
-15 +15
0 10
GAIN
HI PASS
PEAK
LEFT speaker RIGHT speaker
0 10
GAIN
PEAK
50
260
80
120
60
Hz
PHASE
SHIFT
0 - 180°
Subwoofer
50
260
80
120
60
Hz
50
260
80
120
60
Hz
HIGH
PEAK
HIGH
3
6 6
POWER
stays about within 0 e +3 dB.
6
to flash shortly for less than 1 second.
3
RESPONSE DIAGRAM TRIO CLUB
Memorize the knobs setting.
As a general rule , the output level of the mixers should be set so that the sound peaks remain between 0 to +3 dB
about. When the system TRIO CLUB gets in the two Line In (10 and 11) a signal with that amplitude and it is
set as explained above, it grants the maximum performance in terms of maximum undistorted amplification (at clip
limit) and in this conditions you get the maximum possible sound pressure (SPL).
SYSTEM COMPONENTS
Thi TRIO CLUB stereo system is composed by three elements:
Active Subwoofer STAGE PRO W10
1 Active Subwoofer STAGE PRO W10
2 Passive Satellites STAGE PRO 65
Connections and Control Panels
The active subwoofer STAGE PRO W10 is equipped with a
The cabinet integrates all necessary electronics for amplification and system
3 amplifiersi in AB Class for a total power of 500 W RMS (1000 W Max)
10" (250 mm) woofer with 50 mm VC.
1 x 250 W RMS (500 W Max) for the Subwoofer itself
2 x 125 W RMS (250 W Max) for the two passive satellites (@ 4 Ohm load)
processing:
The Subwoofer signal is LowPass filtered, adjustable from 46 to 240 Hz 12 dB/oct.
Cabinet of high density MDF, anti-scratch embossed painting
Sizes & weight: 43 x 39 x 39 cm; 32 kg.
Practical transport handles hollowed into the wood
Integral rigid metal grill
Housing hole for ø 35 mm stand tubes
On/Off power switch - In positioe 0 the system is Off
15
16
Voltage Selector
17
Power Net Socket
Left Channel Lin In
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
Right Channel Line In
10
11
Speakon Socket Right Satellite
12
Speakon Socket Left Satellite
13
Amplifier cooling fan; keep it clean for a correct ventilation.
14
Combo Socket XLR 3-F / Jack 6,3 mm Balanced
The Satellites signals are HighPass filtered, adjustable from 38 to 250 Hz 12 dB/oct.
1
Subwoofer Clip Indicator
2
Subwoofer LOW PASS control adjustable from 46 to 240 Hz
3
Subwoofer Volume control
4
Phase Switch 0-180°
5
Satellites Clip Indicator (Separated Left and Right)
6
Satellites Volume control separated on channel LEFT and RIGHT.
it controls only the signal going respectively to left and right satellite.
High tones equalization separated for left and right channel -15 / +15 dB
7
8
Satellites HI PASS control separated LEFT and RIGHT from 38 to 250 Hz
9
ON LED indicator (Red)
ATTENTION: the HI PASS frequency should not be set under 120 Hz
18
ST/MONO Switch (Stereo / Mono): se si seleziona STEREO,
correspondent Right and Left input signals.
When the system sends to both Right and Left channels only MONO is selected,
the LEFT input signal, so one complete system per channel can be used..
When STEREO is selected, the system sends to the Right and Left channels the
- 4 -
- 5 -
HIGHHIGH HIGHHIGH HIGH HIGH HIGH HIGH
EQEQ EQEQ EQ EQ EQ EQ
MIDMID MIDMID MID MID MID MID
12 kHz12 kHz 12 kHz12 kHz 12 kHz 12 kHz 12 kHz 12 kHz
2.5 kHz2.5 kHz 2.5 kHz2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz
LOWLOW LOWLOW LOW LOW LOW LOW
80 Hz80 Hz 80 Hz80 Hz 80 Hz 80 Hz 80 Hz 80 Hz
PREPREPREPREPREPRE PREPRE
AUXAUXAUXAUXAUXAUX AUXAUX
FXFXFXFXFXFX FXFX
PANPAN PANPAN PAN PAN BAL BAL
31
4
2 5 6 7/8 9/10
MUTEMUTE MUTEMUTE MUTE MUTE MUTE MUTE
ALT 3-4ALT 3-4 ALT 3-4ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4
CLIPCLIP CLIPCLIP CLIP CLIP CLIP CLIP
SOLOSOLO SOLOSOLO SOLO SOLO SOLO SOLO
MUTEMUTE MUTEMUTE MUTE MUTE MUTE MUTEdBdB dBdB dB dB dB dB
1 2
5
6
9/10
111111 11 2 2
1 1 1
222222 22
AL T MAIN MIX
3-4
3
4
L
R
SOLO
SOLO
FX FX
TO AUX
SEND 1
MAIN MIX
ALT 3-4
AUX SENDS STEREO AUX RETURNS
PROGRAM
( PUSH )
2-TR/USB
ALT 3-4
MAIN MIX
SOURCE
MAX
2-TR/USB TO MAIN
PHONES/CTRL R
MAIN SOLO PFL
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
10
5
2
0
2
5
20
MIC 3MIC 1 MIC 4MIC 2 MIC 5 MIC 6
LINE IN 5/6 LINE IN 7/8
RIGHTLEFT/MONO
AUX SENDS
2
1
2
1
FX
INPUT OUTPUT
CD/TAPE
00 SMALL HALL
03 MID HALL
06 BIG HALL
09 CHURCH
10 SMALL ROOM
13 MID ROOM
16 BIG ROOM
19 CHAPEL
20 SPRING
27 SPRING
30 GATED REV
36 REVERSE
40 EARLY REFL
44 AMBIENCE
48 STADIUM
49 AMBIENCE FX
50 DELAY
59 ECHO
60 CHORUS
66 FLANGER
70 PHASER
74 PITCH SHIFT
80 CHORUS & REVERB
82 FLANGER & REVERB
84 PHASER & REVERB
86 PITCH & REVERB
88 DELAY & REVERB
90 DELAY & GATED
91 DELAY & REVERSE
92 DELAY & CHORUS
94 DELAY & FLANGER
96 DELAY & PHASER
98 DELAY & PITCH
24-BIT MULTI-FX PROCESSOR
ULTRALOW-NOISE DESIGN
14-INPUT 2/2-BUS MIC/LINE MIXER
WITH PREMIUM MIC PREAMPLIFIERS AND
DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR
USB AUDIO INTERFACE
3
4 7/8
PAM X 2 .6 2
LAM P
12V
400 mA
USB
INTERFA CE
HIGHHIGH HIGHHIGH HIGH HIGH HIGH HIGH
EQEQ EQEQ EQ EQ EQ EQ
MIDMID MIDMID MID MID MID MID
12 kHz12 kHz 12 kHz12 kHz 12 kHz 12 kHz 12 kHz 12 kHz
2.5 kHz2.5 kHz 2.5 kHz2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz 2.5 kHz
LOWLOW LOWLOW LOW LOW LOW LOW
80 Hz80 Hz 80 Hz80 Hz 80 Hz 80 Hz 80 Hz 80 Hz
PREPREPREPREPREPRE PREPRE
AUXAUXAUXAUXAUXAUX AUXAUX
FXFXFXFXFXFX FXFX
PANPAN PANPAN PAN PAN BAL BAL
31
4
2 5 6 7/8 9/10
MUTEMUTE MUTEMUTE MUTE MUTE MUTE MUTE
ALT 3-4ALT 3-4 ALT 3-4ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4 ALT 3-4
CLIPCLIP CLIPCLIP CLIP CLIP CLIP CLIP
SOLOSOLO SOLOSOLO SOLO SOLO SOLO SOLO
MUTEMUTE MUTEMUTE MUTE MUTE MUTE MUTEdBdB dBdB dB dB dB dB
1 2
5
6
9/10
111111 11 2 2
1 1 1
222222 22
AL T MAIN MIX
3-4
3
4
L
R
SOLO
SOLO
FX FX
TO AUX
SEND 1
MAIN MIX
ALT 3-4
AUX SENDS STEREO AUX RETURNS
PROGRAM
( PUSH )
2-TR/USB
ALT 3-4
MAIN MIX
SOURCE
MAX
2-TR/USB TO MAIN
PHONES/CTRL R
MAIN SOLO PFL
MODE
SOLO (NORMAL)
PFL (LEVEL SET)
10
5
2
0
2
5
20
MIC 3MIC 1 MIC 4MIC 2 MIC 5 MIC 6
LINE IN 5/6 LINE IN 7/8
RIGHTLEFT/MONO
AUX SENDS
2
1
2
1
FX
INPUT OUTPUT
CD/TAPE
00 SMALL HALL
03 MID HALL
06 BIG HALL
09 CHURCH
10 SMALL ROOM
13 MID ROOM
16 BIG ROOM
19 CHAPEL
20 SPRING
27 SPRING
30 GATED REV
36 REVERSE
40 EARLY REFL
44 AMBIENCE
48 STADIUM
49 AMBIENCE FX
50 DELAY
59 ECHO
60 CHORUS
66 FLANGER
70 PHASER
74 PITCH SHIFT
80 CHORUS & REVERB
82 FLANGER & REVERB
84 PHASER & REVERB
86 PITCH & REVERB
88 DELAY & REVERB
90 DELAY & GATED
91 DELAY & REVERSE
92 DELAY & CHORUS
94 DELAY & FLANGER
96 DELAY & PHASER
98 DELAY & PITCH
24-BIT MULTI-FX PROCESSOR
ULTRALOW-NOISE DESIGN
14-INPUT 2/2-BUS MIC/LINE MIXER
WITH PREMIUM MIC PREAMPLIFIERS AND
DIGITAL 24-BIT MULTI-EFFECTS PROCESSOR
USB AUDIO INTERFACE
3
4 7/8
PAM X 2 .6 2
LAM P
12V
400 mA
USB
INTERFA CE
NET
OUT+:1+/
OUT- :1-
OUTPUT
LEFT RIGHT
SPEAKER OUTPUT:
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
LEFT(Mono)
RIGHT
ST
MONO
LINE IN
USE ONLY WITH 250V FUSE
220
OUT+:1+/
OUT- :1-
OUTPUT
LEFT RIGHT
SPEAKER OUTPUT:
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
LEFT(Mono)
RIGHT
ST
MONO
LINE IN
USE ONLY WITH 250V FUSE
220
OUT+:1+/
OUT- :1-
OUTPUT
LEFT RIGHT
SPEAKER OUTPUT:
GND=1=SLEEVE HOT=2=TIP COLD=3=RING
LEFT(Mono)
RIGHT
ST
MONO
LINE IN
USE ONLY WITH 250V FUSE
220
NET
LEFT CHANNEL
LEFT CHANNEL
RIGHT CHANNEL
RIGHT CHANNEL
Portable Full Range Sound System TRIO CLUB Portable Full Range Sound System TRIO CLUB
Depending on the choosen configuration, connect the system following the precedent wiring schemes.
.
System Volume setting
The TRIO CLUB system is provided vith clip limiters and peack level indicators separate and independent on all three
Thus the system is able to deliver excellent performances, and should be used with input signals at optimal level, starting from
kind and quality of the used cables, and the prevention of any kind of distortion.
In fact the presence of distortion doesn’t only deliver a poor performance of the system, but it is also a real risk on long periods,
We kindly invite you therefore,to strictly follow the following instructions on how to set the level of alla components.
channels, and doesn’t require therefore any special setting procedure.
CONNECTION OF TWO SYSTEMS IN MONO CONFIGURATION
(ST/MONO Switch down)
Connection to the electric net
Check that Power switch is in position 0 and that net voltage corresponds to the one selected in the system.
.
Connect the supplied electric wire to an electric net socket equipped with a correct ground contact.
Connection to the mixer
Before making any connection to the mixer make sure the system power switch is Off in order to avoid damages.
Remember that electric net power il the last to be switced On and the first to be disconnected after use!
Satellite connection
Use wires with good quality Speakon plugs. Make sure to rotate the Speakon plugs clockwise up to the lock position.
15
to damage the system itself.
SYSTEM CONNECTION IN STEREO CONFIGURATION
(ST/MONO Swich up)
High sensitivity passive satellites STAGE PRO 65
The high sensitivity passive satellite STAGE PRO 65 is a bass reflex
One 6.5" (165 mm) woofer with a 32 mm vented voice coil
One DOME tweeter with a 30 mm voice coil
Cabinet in high density MDF , embossed anti-scratch painting
Housing hole for ø 35 mm stand tubes
Integral protection grill
High Pass Filter at 6000 Hz 12 dB/oct on tweeter
4 ohm Impedance
Speakon socket for connection to the subwoofer amplifier
Sizes and Weight: 20 x 19 x 27 cm; 5 kg.
cabinet equipped with:
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Audio Design Pro Trio Club User manual

Brand
Audio Design Pro
Model
Trio Club
Category
Audio mixers
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents