Samsung HW-S50A User manual

HW-S50A

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

•To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

•TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

•This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

•To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

•Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

•To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

Wiring the Main Power Supply

Plug (UK Only)

IMPORTANT NOTICE

The mains lead on this equipment is supplied with

a moulded plug incorporating a fuse. The value of

the fuse is indicated on the pin face of the plug

and if it requires replacing, a fuse approved to

BS1362 of the same rating must be used.

Never use the plug with the fuse cover removed.

If the cover is detachable and a replacement is

required, it must be of the same colour as the fuse

tted in the plug. Replacement covers are

available from your dealer. If the tted plug is not

suitable for the power points in your house or the

cable is not long enough to reach a power point,

you should obtain a suitable safety approved

extension lead or consult your dealer for assistance.

ENG - 3

However, if there is no alternative to cutting off the

plug, remove the fuse and then safely dispose of

the plug. Do not connect the plug to a mains

socket as there is a risk of shock hazard from the

bared exible cord. Never attempt to insert bare

wires directly into a mains socket. A plug and fuse

must be used at all times.

IMPORTANT

The wires in the mains lead are coloured in

accordance with the following code:– BLUE =

NEUTRAL BROWN = LIVE As these colours may not

correspond to the coloured markings identifying

the terminals in your plug, proceed as follows:– The

wire coloured BLUE must be connected to the

terminal marked with the letter N or coloured

BLUE or BLACK. The wire coloured BROWN must

be connected to the terminal marked with the

letter L or coloured BROWN or RED.

WARNING : DO NOT CONNECT EITHER WIRE TO

THE EARTH TERMINAL WHICH IS MARKED WITH

THE LETTER E OR BY THE EARTH SYMBOL ,

OR COLOURED GREEN OR GREEN AND YELLOW.

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

CAUTION : Danger of explosion if the battery

is replaced incorrectly. Replace only with the

same or equivalent type.

ENG - 4

Fabric cleaning

Remove any dirt or stain on the product surface

immediately.

Removing and cleaning can be less effective for

some substances or if left for a prolonged time.

CAUTION

•Use a vacuum cleaner or an adhesive lint

roller to remove dust, handprints, and the

likes.

– Some cleaning brushes may damage the

product, depending on the materials they

contain.

– Towels and cleaning clothes may leave

lint or dirt on the product.

•Do not use a nail or other tools to scratch the

dirt off. It may damage the fabric.

•To remove oil or liquid stains, use a clean

white cloth moist with water. If the stain

persists, wipe it with a mixture of water and

neutral detergent (such as dishwashing

soaps) and a cloth.

– A non-neutral detergent or cleaner may

cause discolouration or fabric damage.

– After cleaning, use a dry cloth or

hairdryer to dry the area.

– Do not use excessive force to avoid

discolouration or fabric damage.

ENG - 5

CONTENTS

01 Checking the Components 7

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 7

02 Product Overview 8

Top Panel of the Soundbar ------------------------- 8

Bottom Panel of the Soundbar ------------------------- 9

03 Using the Remote Control 10

How to Use the Remote Control ------------------------- 10

Using the Hidden Buttons (Buttons with more than one function) ------------------------- 15

Output specications for the different sound effect modes ------------------------- 15

Adjusting the Soundbar volume with a TV remote control ------------------------- 16

04 Connecting the Soundbar 17

Connecting Electrical Power ------------------------- 17

Connecting an SWA-9100S (Sold Separately) ------------------------- 18

Connecting an SWA-W500 (Sold Separately) ------------------------- 20

05 Using a wired connection to the TV 22

Method 1. Connecting with HDMI ------------------------- 22

Method 2. Connecting using an Optical Cable ------------------------- 24

06 Using a wireless connection to the TV 26

Connecting via Bluetooth ------------------------- 26

ENG - 6

07 Connecting an External Device 28

Connecting using an Optical Cable ------------------------- 28

08 Connecting a USB Storage Device 29

09 Connecting a Mobile Device 31

Connecting via Bluetooth ------------------------- 31

Using Tap Sound ------------------------- 36

10 Installing the Wall Mount 37

Installation Precautions ------------------------- 37

Wallmount Components ------------------------- 37

11 Installing the Soundbar in front of TV 39

12 Software Update 40

Reset ------------------------- 41

13 Troubleshooting 42

14 Licence 43

15 Open Source Licence Notice 44

16 Important Notes About Service 44

17 SpecicationsandGuide 45

Specications ------------------------- 45

ENG - 7

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Soundbar Remote Control

/ Batteries

AC/DC Adapter (Soundbar) Power Cord (Soundbar)

x 2

(M4 x L10)

x 2 x 2

Wall Mount Guide Holder-Screw Screw Bracket-Wall Mount

•For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

•To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

•For more information about the wallmount see page 37.

•Design, specications are subject to change without prior notice.

•The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the back cover back into position.

ENG - 8

02 PRODUCT OVERVIEW

Top Panel of the Soundbar

Top Panel

Position the product so that

the SAMSUNG logo is

located on the top.

󰟶󰟴 󰟵

󰟳

󰟳LED

indicator

The LED Indicator ashes, glows, or changes colour depending on the Soundbar's current

mode or status. The colour of the LED indicator and the number of lights indicate the active

mode as described below.

W

White LED

W

White LED

M

Multicolour LED

W

White LED

W

White LED

•The Multicolour LED changes to White, Cyan, Green, Red, Yellow, Orange, Purple and

Blue depending on the mode or status.

󰟴Power Turns the power on and off.

󰟵Volume Adjusts the volume.

󰟶Source

•Press the (Source) button to change the mode. Each time you change the mode,

the LED lights in white and then turns off.

LED

Indicator

White On -> Off White On -> Off White On -> Off

“Digital Audio In” or

“TV ARC”“Bluetooth” “USB”

ENG - 9

•When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

•When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

•If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and

change the TV speaker to External Speaker.

Bottom Panel of the Soundbar

ID SET NETWORK

USB (5V 0.5A)

DC 24V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

DC 24V

ID SET NETWORK

USB (5V 0.5A)

DC 24V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

DC 24V

ID SET NETWORK

USB (5V 0.5A)

DC 24V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

DC 24V

󰟳 󰟴 󰟵 󰟶

󰟳USB (5V 0.5A)

Connect a USB device here to play music les stored on the USB device through the Soundbar.

󰟴DC 24V (Power Supply In)

Connect the AC/DC power adapter.

󰟵DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device.

󰟶HDMI (ARC)

Connect to the HDMI (ARC) port on a TV.

•When disconnecting the power cable of the AC/DC power adapter from a wall outlet, pull the plug.

Do not pull the cable.

•Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 10

03 USING THE REMOTE CONTROL

How to Use the Remote Control

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

󰟳

󰟴

󰟵

󰟶

󰟷

󰟹

󰟸

󰟺

󰟼

󰟻

󰟳Power

Turns the Soundbar on and off.

LED

Indicator

Cyan Blinks X1

On Off

Red Blinks X3

•Auto Power Down Function

The unit turns off automatically in the following

situations:

– In “Digital Audio In” or “TV ARC” / “Bluetooth” /

“USB” mode if there is no audio signal for 20 minutes.

󰟴 (Source)

Press to select a source connected to the Soundbar.

󰟵 (Mute)

Press the (Mute) button to mute the sound.

Press it again to unmute the sound.

LED

Indicator

Blinks X Repeatly

ENG - 11

󰟶SOUND MODE

By pressing the button, you can select the desired audio mode. Each time the mode changes, the

Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Adaptive Sound”  “Music”  “DTS Virtual:X”  “Standard”

– Adaptive Sound

Analyzes the content in real time and automatically provides an optimal sound eld based on the

characteristics of the content.

– Music

Provides more natural and room lling sound for music content.

– DTS Virtual:X

Immersive 3D sound from any content.

– Standard

Outputs the original sound.

•Bluetooth Power On/Off

This feature automatically turns the Soundbar on when it receives a connection request from a

previously connected TV or Bluetooth device. The setting is On by default.

– Press and hold the SOUND MODE button for more than 5 seconds to turn off the Bluetooth

Power function.

•DRC (Dynamic Range Control) On/Off

Lets you apply dynamic range control to Dolby Digital tracks. Press and hold the SOUND MODE

button for more than 5 seconds while the Soundbar is powered off to turn DRC (Dynamic Range

Control) on or off. With the DRC turned on, loud sound is reduced. (The sound may be distorted.)

SOUND MODE button LED Indicator

VOL WOOFER

SOUND

MODE

PAIR

5 Sec Cyan Blinks X1

On (Default) Off

Red Blinks X1

DRC On/Off Toggle On  Off

ENG - 12

󰟷 Bluetooth PAIR

Switch the Soundbar to Bluetooth pairing mode.

When you press the button, the LED display changes as shown below.

•Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

LED

Indicator

Red → Green → Blue Blinks

Pairing Connection is complete

Cyan Blinks X3

󰟸p (Play / Pause)

You can also play or pause music by pressing the button in "USB" mode.

󰟹Up/Down/Left/Right

Press Up/Down/Left/Right on the button to select or set functions.

•Repeat

To use the Repeat function in “USB” mode, press the Up button.

•Music Skip

Press the Right button to select the next music le. Press the Left button to select the previous

music le.

ENG - 13

󰟺 (Sound Control)

By pressing the button, you can select the desired audio mode. The desired settings can be adjusted

using the Up/Down buttons. Each time the mode changes, the Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Treble”  “Bass”  “Sync”  “Centre Level”

– To control the volume of the treble or bass sound, select “Treble”, “Bass”, “Sync”, or “Centre Level” in

Sound Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.

7 Band EQ

Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for each

frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the Left/

Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down buttons.

(Make sure the Sound mode is set to “Standard”.)

7 Band EQ

VOL WOOFER

SOUND

MODE

PAIR

5 Sec

Press and hold the (Sound Control) button

for about 5 seconds.

Using the Left/Right buttos and each can be

adjusted to setting between -6 to+6.

“150Hz”“150Hz”  “300Hz”  “600Hz”  “1.2kHz” 

“2.5kHz”  “5kHz”  “10kHz”

– To control the volume of the each speaker select “Centre Level” in Sound Settings, and then adjust

the volume between -6~+6 by using the Up/Down buttons.

– If the video on the TV and audio from the Soundbar are not synchronised, select “Sync” in Sound

Control, and then set the audio delay between 0~300 milliseconds by using the Up/Down buttons.

(Not available in “USB” or “Bluetooth”mode.)

– “Sync” is only supported for some functions.

ENG - 14

󰟻WOOFER (BASS) LEVEL

SOUND

MODE

VOL WOOFER

SOUNDBAR

SOUND

MODE

VOL WOOFER

SOUNDBAR

SOUND

MODE

VOL WOOFER

SOUNDBAR

SOUND

MODE

VOL WOOFER

SOUNDBAR

When subwoofer is connected, push the button up or down to adjust the woofer level to -12 or between -6

to +6. When subwoofer is disconnected, push the button up or down to adjust the bass level between -6

to +6.

To set the woofer (bass) volume level to 0 (Default), press the button. (If Soundbar connected to

wireless subwoofer (sold separately)).

󰟼VOLUME

Push the button up or down to adjust the volume.

LED

Indicator

White moves to right X1

Volume Up

White moves to left X1

Volume Down

ENG - 15

Using the Hidden Buttons (Buttons with more than one function)

Hidden Button

Reference page

Remote Control Button Function

WOOFER (Up) TV remote control On/Off page 16

Left TV Auto connect On/Off page 27

Up ID SET page 19

(Sound Control) 7 Band EQ page 13

SOUND MODE DRC On/Off page 11

Bluetooth Power On/Off page 11

PAIR Bluetooth Multi connection On/Off page 34

Outputspecicationsforthedifferentsoundeffectmodes

Effect Input

Output

With Soundbar only With Subwoofer Only With Subwoofer &

Wireless Rear Speaker Kit

Adaptive Sound 2.0 ch 3.0 ch 3.1 ch 5.1 ch

5.1 ch 3.0 ch 3.1 ch 5.1 ch

Music 2.0 ch 3.0 ch 3.1 ch 5.1 ch

5.1 ch 3.0 ch 3.1 ch 5.1 ch

DTS Virtual:X 2.0 ch 3.0 ch 3.1 ch 5.1 ch

5.1 ch 3.0 ch 3.1 ch 5.1 ch

Standard 2.0 ch 2.0 ch 2.1 ch 2.1 ch

5.1 ch 3.0 ch 3.1 ch 5.1 ch

•The Samsung Wireless Rear Speaker Kit, and Subwoofer can be purchased separately.

To purchase a Kit or the Subwoofer, contact the vendor you purchased the Soundbar from.

ENG - 16

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

•This function can be used with IR remote controls only. Bluetooth remote controls (remote

controls that require pairing) are not supported.

•Set the TV speaker to External Speaker to use this function.

•Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

TV remote control On/Off

1. Turn Off the Soundbar.

2. Push up and hold the WOOFER button for 5 seconds.

Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the

following order: “Off-TV Remote” (Default mode), “Samsung-TV Remote”, “All-TV Remote”.

The LED indicator status changes each time the mode is changed, as shown below.

Remote Control Button LED Indicator Status

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"Off-TV Remote"

(Default mode)

Red Blinks X1

Disable the TV remote control.

SOUND

MODE

VOL WOOFER

SOUNDBAR

5 Sec

"Samsung-TV Remote"

Cyan Blinks X1

Enable a Samsung TV’s IR remote

control.

SOUND

MODE

VOL WOOFER

SOUNDBAR

5 Sec

"All-TV Remote"

Blue Blinks X1

Enable a third-party TV’s IR remote

control.

ENG - 17

04 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components to connect the Soundbar to an electrical outlet in the following order:

•For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

1. First connect the power cable to the AC/DC adapter.

Connect the AC/DC adapter (with the power cable) to the Soundbar.

2. Connect the power cord to a wall socket.

DC 19V

Power Cord

AC/DC Adapter

Bottom of the Soundbar Main Unit

ID SET NETWORK

USB (5V 0.5A)

DC 24V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

DC 24V

ID SET NETWORK

USB (5V 0.5A)

DC 24V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

USB (5V 0.5A)

DC 24V

DC 19V

NOTES

•If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on

automatically.

•Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

ENG - 18

Connecting an SWA-9100S (Sold Separately)

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-9100S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– When connecting the speaker cable, connect the core wire to the speaker.

SURROUND-RIGHT SURROUND-RIGHT

– The speaker cables are colour coded.

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

•The LINK LED indicator (blue LED) on the Wireless Receiver Module blinks. If the LED does not

blink, press the ID SET button on the back of the Wireless Receiver Module with a pen tip for

5~6 seconds until the LINK LED indicator blinks (in Blue). For more about the LED, please refer

to the SWA-9100S user manual.

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

STANDBY

LINK

STANDBY

LINK

Blue blinking

5 Sec

ENG - 19

3. ID SET

Press the Up button on the remote control for 5 seconds.

•Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

Remote Control Button LED Indicator

SOUND

MODE

PAIR

5 Sec

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

CAUTION

•If your Soundbar was playing music when it connects to the SWA-9100S, you may hear some

stuttering from the woofer as the connection nalizes.

4. Check if the LINK LED is solid blue (connection complete).

STANDBY

LINK

STANDBY

LINK

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Receiver Module.

5. If the SWA-9100S is not connected, repeat the procedure from Step 2 through 4.

ENG - 20

Connecting an SWA-W500 (Sold Separately)

1. Turn off the Soundbar by pressing the (Power) button on the remote control.

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Red Blinks X3

2. Plug in the Wireless Subwoofer, and then check its standby status.

•Plug the Wireless Subwoofer power cord into an electrical outlet and into the Wireless

Subwoofer to turn on the Wireless Subwoofer. The LINK LED indicator (blue LED) on the

Wireless Subwoofer blinks. If the LED does not blink, press the ID SET button on the rear of the

Wireless Subwoofer with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).

For more about the LED, please refer to the SWA-W500 user manual.

Rear of the Wireless Subwoofer

POWER ID SET

Front of the Wireless Subwoofer

POWER ID SET

Blue blinking

POWER ID SET

ID SET

5 Sec

•The main unit is heavy. Be careful not to pinch your ngers when pressing the ID SET button or

connecting the power cord to the rear of the unit.

•The upper part of the subwoofer is prone to scratches. Handle it carefully.

Speaker Unit

Bottom of the Wireless Subwoofer

•Do not press on or strike the

Speaker Unit on the bottom of

the body. You can deform or

damage the speaker.

Page is loading ...

Samsung HW-S50A User manual

Samsung HW-S50A User manual

Related papers

Other documents