Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
1
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
2
Index
Pages
INTRODUCTION: 2
SERVICING INSTRUCTIONS: 5 - 9
TECHNICAL INFORMATION SHEETS:
Contour L 13 10
Contour L 23 11
Contour L 33 12
Contour L 43 13
Contour L 53 14
Contour L 63 15
Profiler P 23 16
Profiler P 33 17
Profiler P 43 18
Profiler P 53 19
Profiler P 63 20
Advance F 13 21
Advance F 23 22
Advance F 33 23
Advance F 43 24
Advance F 53 25
MOTOR CIRCUIT DIAGRAMS 26 - 27
COOLER CIRCUIT DIAGRAM 28
INSTALLATION
Wiring the cooler to Networker 29 - 30
Installing Multiple coolers on a Network 31
Installing dual Networkers 32 - 34
Networker Installer Parameters 35
COOLER SERVICE PARAMETERS 36 - 39
COOLER OPERATION
General Operation 40 - 43
Wash Service 44
Flush Service 46
Aquasave Operation 47
N-E5 Electronic Control Operation 48 - 50
Fan Operation 51 - 59
Pump Operation 60 - 65
Water Inlet Solenoid Operation 66 - 70
Servo Seal & Drain Valve Operation 71 - 76
Trident Water Management 77 - 90
DEALING WITH PROBLEM INSTALLATIONS 91 - 95
SERVICE MAINTENANCE 96 - 100
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
3
Introduction
In August 2003 Brivis introduced the new 3 series Contour cooler and also a lesser featured contour
was also introduced called the Brivis Profiler.
The Brivis Profiler cooler was introduced to offer a budget model Contour to meet market demand.
The Brivis Profiler looks very similar to the Contour with its sloping base, but slight changes have
been made to the decorative panels. The Brivis Profiler cooler is also slightly smaller in height than
the Contour.
Brivis Contour Brivis Profiler
Both models, Brivis Profiler and Contour, now use the N-E5 control box instead of the older N-E4.
The main difference in the N-E5 control is the removal of the isolating switch from the top of the
control box. This isolating switch has been relocated to the underside of the cooler so that the
power can be isolated without removing the front pad. There has also been some software changes
to the N-E5.
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
4
Brivis Advance
The Brivis Advance was introduced in 2005 and is designed to take the place of the AD range of
units up to Model AD56. However, the AD76 and AD86 will remain in production.
In essence the Advance is a square shaped Contour/Profile, which sits upon the same base frame
as the Contour/Profiler. So for the purpose of servicing, all the electrical and operational
components are the same and therefore all the information contained in these manuals is relevant.
The BASE is square and sits on a vertical dropper box similar to the AD units, except that the
dropper box should come with outwards turned flange so that the locking brackets on the unit attach
to the dropper box. Like the AD unit, the cooler should be located high enough on the roof to
prevent the back from touching the roof.
The PAD FRAMES are attached in a similar fashion to the Contour and Profile unit. The front and
rear pads can be removed by first lifting the roof assembly, and then lifting the pad assembly out;
the same way the Contour and Profiler work.
The SIDE PAD FRAMES are slightly different and involve the pad frame being rolled into the centre
of the unit and then being raised out. It is important that the pad frame is not forced, as this could
damage the alloy brackets.
The ROOF ASSEMBLY also remains the same as the Profiler/Contour units.
Some standard features differ between the Brivis Profiler, Contour and Advance.
Components
Brivis
Contour
Brivis
Profiler
Brivis
Advance
Motorised winter seal (Servoseal) Yes No No
Counter balanced weather-seal N/A Optional Optional
Motorised dump valve Yes Yes Optional
Aquasave Yes No No
Speed Sensor Yes Yes Yes
Networker compatible Yes Yes Yes
Water sensor Yes Yes Yes
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
5
BRIVIS
SERVICING
INSTRUCTIONS
Retrofitting the Service N-E5 to 0, 1 & 2 Series Contours.
The service N-E5 control can be used as a replacement control for all previous model coolers,
however some parameters need to be adjusted in order for the control to operate correctly. The
table below details all of the parameter adjustments that need to be made for each model cooler
when fitting an N-E5 into an older model Contour. These parameters are located in the cooler
service parameter section, and can only be accessed by using a Networker.
N-E5 parameter adjustments.
Parameter
number
Parameter description Default
setting
0 Series
Contour
1 Series
Contour
2 Series
Contour
3 Series
Contour or
Profiler
3 Series
Advance
05
Model selection number -
Determines min & max
fan speeds.
1
Check
specification
sheet
Check
specification
sheet
Check
specification
sheet
Check
specification
sheet
Check
specification
sheet
15
Flush count -
Number of refills before
flushing occurs.
20 20 20
20
Non Aquasave
250 Aquasave
20
Non Aquasave
250 Aquasave
20
22
Aquasave - Allows
N-E5 to power Aquasave
module.
1 = Enabled
0 = Disabled
0 0 0
0
Aquasave
powered by
pump power
supply.
1 – Contour
0 - Profiler
Advance - 0
43 Flush time -
Time
solenoid is open during flush.
200
sec
100
sec
60
sec
200
sec
200
sec
200
sec
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
6
BRIVIS
SERVICING
INSTRUCTIONS
No. 21
N-E5 Cooler Control Dump Delay Parameter.
Units affected:
All Version 3 Contours and Profiler coolers using N-E5 electronic controller.
Reason for change:
R&D have informed us of a change within the N-E5 service parameters. which has the potential to
cause a problem. This change has happened mid production and has affected the first 2020 units.
The problem has occurred to service parameter 01, which relates to the Dump Delay time. The
change is with the way the parameter is read. Usually the parameter unit was in single minutes, but
on the newer N-E5 controllers it has been changed to units of 10 minutes.
For example
- Normal setting was 60, meaning 60 minutes before the cooler would dump.
- New setting is 6, meaning 6 lots of 10 minutes which equals 60 minutes.
If service parameter 01 on the newer N-E5 is changed to 60 when we service these units, it
will then dump after 10 hours (60 x 10 minutes = 600 minutes). Vice Versa if Parameter 01 on
the first version N-E5 is set to 6, it will then dump after 6 minutes.
In both cases this will cause a fairly major upset with the units normal operation. We can trace the
individual controllers by their serial number. The first 2020 controllers have the dump delay setting
units in minutes, and the rest of the production controllers will all have the dump delay setting units
in lots of 10 minutes.
N-E5 Serial Numbers - 18764 020 0000 to 18764 020 2020 have the dump delay in single minutes.
N-E5 Serial Numbers - 18764 020 2021 and Beyond will have the dump delay setting in lots of 10
minutes.
N-E5 - Version 9, 9a & 10 will have the dump delay setting in lots of 10 minutes.
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
7
BRIVIS
SERVICING
INSTRUCTIONS
No. 23
N-E5 Cooler Control Upgrade
(This issue (2) replaces previous versions of servicing instruction #23 (issue 1))
Units affected: 3 Series Contours and Profilers.
Background: The version 7 N-E5 (original control) has proven to be unreliable, with the majority of
failures occurring with the Servo-seal action. The Version 8 N-E5 was introduced to fix this problem.
A tracking problem then started occurring on the trident water sensor. This coupled with lengthy fill
problems (software related) caused the units to operate OK for 2/3 hours before blowing hot air.
R&D have introduced the version 9 N-E5 control, which has had modifications done to the software.
This has improved the failure rate on the Servo-seal (further enhancement from the version 8), and
water level control problems, including refill times, have been rectified. Unfortunately the version 9
also suffered from Servo-seal failures, albeit few in number.
Root cause analysis has since proven that the cause of Servo-seal failures is due to power spikes
degrading PCB components. The version 9A is the latest N-E5 control, which has been upgraded to
protect components from power spikes. Field tests have already proven that the version 9A N-E5 is
very reliable.
The Version 9A controllers can be identified by the marking "9A" on the box.
Action: Technicians, when attending any 3 series cooler (Brivis Profiler or Contour), need to
complete these steps:
Identify the version of controller in the cooler and replace all N-E5 controls (version 7, 8 or 9) with
the new version "9A" controller. Version 8 controllers will be marked with an "8" on the box, and
version 9 controllers with a "9", while any version 7 and before will have no marking on the box.
Correctly label the control box with a defect sticker marked "TO BE REWORKED".
Test cooler for correct operation.
Complete your job sheet with the information below.
Documentation: These notes should be included on your POD invoice.
If the part failed before you attended the job-
Fault Part Fault Description
18764 2 Short description of the fault
If the part did not fail and was upgraded as per the Servicing instruction-
Fault Part Fault Description
18764 111 N-E5 Upgraded
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
8
BRIVIS
SERVICING
INSTRUCTIONS
No. 22
Trident Water Sensor Tracking Problems
Units affected: All Contours 1,2 & 3 Series, and Profiler 3 Series.
Background: It has been found in the field that the trident water sensor can be subject to false
sensing. This is caused by mineral build up behind the water sensor probes. The cooler may run for
a period of time before the fault occurs, but the fault will eventually result in the pump cavitating
because the unit has failed to fill. The build up on the probes forces the electronic controller to think
the water level is OK, when in actual fact it doesn't really know at what level the water is at.
Action: Service technicians are required to perform this action when attending any 3 series Contour
or Profiler. This action should only be performed on 1 or 2 series Contour coolers if they exhibit the
above symptoms. The installation of a modified water sensor should be carried according to the
installation instructions.
Plastic Housing Modified Sensor
Installation: Modifications have been made to Trident water sensor to help prevent this electrical
tracking on the water sensor. The plastic legs on the trident probe housing have been removed,
preventing any build up of minerals at the low point of the probes (see pictures).
Remove the old water sensor from the cooler trough and attach a defective label to part. This part
should be sent to warranty returns. if the unit is under warranty. If the unit is not under warranty this
part is to be charged to the customer.
Replace the water sensor with Part - 18066 - WATER SENSOR ASSY CONTOUR L1, ensuring
that the plastic housing has been modified (see picture above).
Test cooler for correct operation.
Documentation: These notes should be included on your POD invoice.
Fault Part Fault Description
18066 111 Modified water sensor.
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
9
BRIVIS
SERVICING
INSTRUCTIONS
Introduction of 5.5 litre ELBI solenoid
Background: On the 23/11/2004, the 5.5 litre ELBI solenoid was introduced into production for all 3
series Contours and Profilers. it was originally brought into production to try and prevent units from
failing to fill during a water limp error. it was found that the cause was not the limited flow (4 litre
ELBI) of the original solenoid but a water sensing issue. However the supplier of these solenoids
had already delivered 10,000 5.5 - litre solenoids, thus they were used in production.
Action: The introduction of the 5.5 litre solenoid is not expected to make any dramatic change to
the coolers operation. However there is a slight increase of water hammer occurring on the
premises. Tests conducted by our R&D department have proved that the hammer spike generated
by the 5.5 litre ELBI is no greater than our previous 12 litre soft close solenoid. Technicians can
identify the new 5.5 litre solenoid by a blue label that has been placed on the side of the solenoid
valve body.
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
10
Brivis Technical Data
Type: Technical Data Base Date Updated: 13/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 13
Sizing Guide Reference Figure 1000 - 1450
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 48.5 kg
Wet Weight 65.2 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 60 mm Rating 240 V / 50 Hz 10 Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
855BNVA-A12 Winding Resistance 206 Ohms (+/- 8% @ 20oC)
Watts 315 Overflow size 40 mm
Amps 2.4 Waste Outlet Size 40 mm
R.P.M. 1400 Tank Capacity 12 Litres
Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt
Blades 6 RPM 500
Blade Angle 23 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker NC-3
BWC-1 (Electronic)
BWC-2 (Manual)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
11
Brivis Technical Data
Type: Technical Data Base Date Updated: 13/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 23
Sizing Guide Reference Figure 1250 - 1800
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 49.5 kg
Wet Weight 67.3 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 75 mm Rating 240 V / 50 Hz 10 Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
855BNVA-A12 Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 315 Overflow size 40 mm
Amps 2.4 Waste Outlet Size 40 mm
R.P.M. 1400 Tank Capacity 12 Litres
Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt t
Blades 6 RPM 500
Blade Angle 23 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker N-C3
BWC-2 (Manual)
BWC-1 (Electronic)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
12
Brivis Technical Data
Type: Technical Data Base Date Updated: 13/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 33
Sizing Guide Reference Figure 1500 - 2250
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 51.5 kg
Wet Weight 70.4 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 90 mm Rating 240 V / 50 Hz 10 Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohms (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker N-C3
BWC-2 (Manual)
BWC-1 (Electronic)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
13
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 43
Sizing Guide Reference Figure 2000 - 2750
Cabinet detail
Width 1100 mm
Height front 800 mm
Height back 480 mm
Length 1100 mm
Dry Weight 54.5 kg
Wet Weight 75.0 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 90 mm Rating 240 V / 50 Hz 10Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker N-C3
BWC-2 (Manual)
BWC-1 (Electronic)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
14
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 53
Sizing Guide Reference Figure 2400 - 3200
Cabinet detail
Width 1100 mm
Height front 800 mm
Height back 480 mm
Length 1100 mm
Dry Weight 55.6 kg
Wet Weight 77.8 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 110 mm Rating 240 V / 50 Hz 10 Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker N-C3
BWC-2 (Manual)
BWC-1 (Electronic)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
15
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Contour L 63
Sizing Guide Reference Figure 2900 - 3600
Cabinet detail
Width 1100 mm
Height front 800 mm
Height back 480 mm
Length 1100 mm
Dry Weight 56.6 kg
Wet Weight 80.3 kg
Filter Pad Details Water Treatment Unit
Quantity 4 Type WE-1
Thickness 130 mm Rating 240 V / 50 Hz 10 Watt
Type CELDEK 5090 Amps 0.12
Air/Gas Flow Rate 1 L/minute minimum flow
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor ServoSeal Motor
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 Networker N-C3
BWC-2 (Manual)
BWC-1 (Electronic)
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
16
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Profiler P 23
Sizing Guide Reference Figure 1250 - 1800
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 47.0 kg
Wet Weight 64.8 kg
Filter Pad Details
Quantity 4
Thickness 75 mm
Type CELDEK 5090
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
855BNVA-A12 Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 315 Overflow size 40 mm
Amps 2.4 Waste Outlet Size 40 mm
R.P.M. 1400 Tank Capacity 12 Litres
Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor Auto Refresh Tube
Size 538 mm Dia.. Type S.A.I.A
Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt
Blades 6 RPM 500
Blade Angle 23 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 BWC-1 (Electronic)
BWC-2 (Manual)
Networker N-C3
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
17
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Profiler P 33
Sizing Guide Reference Figure 1500 - 2250
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 48.2 kg
Wet Weight 66.0 kg
Filter Pad Details
Quantity 4
Thickness 75 mm
Type CELDEK 5090
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor Auto Refresh Tube
Size 538 mm Dia.. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 BWC-2 (Electronic)
BWC-1 (Manual)
Networker N-C3
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
18
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Profiler P 43
Sizing Guide Reference Figure 2000 - 2750
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 49.0 kg
Wet Weight 67.9 kg
Filter Pad Details
Quantity 4
Thickness 90 mm
Type CELDEK 5090
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor Auto Refresh Tube
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 BWC-1 (Electronic)
BWC-2 (Manual)
Networker N-C3
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
19
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Profiler P 53
Sizing Guide Reference Figure 2400 - 3200
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 49.9 kg
Wet Weight 70.2 kg
Filter Pad Details
Quantity 4
Thickness 110 mm
Type CELDEK 5090
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor Auto Refresh Tube
Size 538 mm Dia.. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 BWC-1 (Electronic)
BWC-2 (Manual)
Networker N-C3
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM
20
Brivis Technical Data
Type: Technical Data Base Date Updated: 15/01/2004
Category: Specification Sheet - Cooler
Subject: Profiler P 63
Sizing Guide Reference Figure 2900 - 3600
Cabinet detail
Width 1100 mm
Height front 720 mm
Height back 400 mm
Length 1100 mm
Dry Weight 50.7 kg
Wet Weight 72.3 kg
Filter Pad Details
Quantity 4
Thickness 130 mm
Type CELDEK 5090
Duct Outlet Size
Width 550 mm
Length 550 mm
Pump / Water Distribution
Motor Pump Type ASKOLL M115
Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps
Model FASCO Pump Capacity 20 L/minute
80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)
Watts 750 Overflow size 40 mm
Amps 4.9 Waste Outlet Size 40 mm
R.P.M. 1350 Tank Capacity 12 Litres
Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE
R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329
R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps
N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute
Coil Resistance 4.1 kOhm approx. @ 20oC
Inlet Valve Size 3/4" BSP (Male) Thread
Fan Impellor Auto Refresh Tube
Size 538 mm Dia. Type S.A.I.A
Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt
Blades 11 RPM 500
Blade Angle 30 deg TIP Resistor 470 Ohm
Collet BRIVIS Capacitor 100 nF
Cooler Control Module Wall Controller
N-E5 BWC-1 (Electronic)
BWC-2 (Manual)
Networker N-C3
Water Connection
Flexible Hose Connection with 1/2" BSP (Male) Thread
Drain Connection
40 mm PVC
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
