Brivis Contour User manual

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

1

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

2

Index

Pages

INTRODUCTION: 2

SERVICING INSTRUCTIONS: 5 - 9

TECHNICAL INFORMATION SHEETS:

Contour L 13 10

Contour L 23 11

Contour L 33 12

Contour L 43 13

Contour L 53 14

Contour L 63 15

Profiler P 23 16

Profiler P 33 17

Profiler P 43 18

Profiler P 53 19

Profiler P 63 20

Advance F 13 21

Advance F 23 22

Advance F 33 23

Advance F 43 24

Advance F 53 25

MOTOR CIRCUIT DIAGRAMS 26 - 27

COOLER CIRCUIT DIAGRAM 28

INSTALLATION

Wiring the cooler to Networker 29 - 30

Installing Multiple coolers on a Network 31

Installing dual Networkers 32 - 34

Networker Installer Parameters 35

COOLER SERVICE PARAMETERS 36 - 39

COOLER OPERATION

General Operation 40 - 43

Wash Service 44

Flush Service 46

Aquasave Operation 47

N-E5 Electronic Control Operation 48 - 50

Fan Operation 51 - 59

Pump Operation 60 - 65

Water Inlet Solenoid Operation 66 - 70

Servo Seal & Drain Valve Operation 71 - 76

Trident Water Management 77 - 90

DEALING WITH PROBLEM INSTALLATIONS 91 - 95

SERVICE MAINTENANCE 96 - 100

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

3

Introduction

In August 2003 Brivis introduced the new 3 series Contour cooler and also a lesser featured contour

was also introduced called the Brivis Profiler.

The Brivis Profiler cooler was introduced to offer a budget model Contour to meet market demand.

The Brivis Profiler looks very similar to the Contour with its sloping base, but slight changes have

been made to the decorative panels. The Brivis Profiler cooler is also slightly smaller in height than

the Contour.

Brivis Contour Brivis Profiler

Both models, Brivis Profiler and Contour, now use the N-E5 control box instead of the older N-E4.

The main difference in the N-E5 control is the removal of the isolating switch from the top of the

control box. This isolating switch has been relocated to the underside of the cooler so that the

power can be isolated without removing the front pad. There has also been some software changes

to the N-E5.

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

4

Brivis Advance

The Brivis Advance was introduced in 2005 and is designed to take the place of the AD range of

units up to Model AD56. However, the AD76 and AD86 will remain in production.

In essence the Advance is a square shaped Contour/Profile, which sits upon the same base frame

as the Contour/Profiler. So for the purpose of servicing, all the electrical and operational

components are the same and therefore all the information contained in these manuals is relevant.

The BASE is square and sits on a vertical dropper box similar to the AD units, except that the

dropper box should come with outwards turned flange so that the locking brackets on the unit attach

to the dropper box. Like the AD unit, the cooler should be located high enough on the roof to

prevent the back from touching the roof.

The PAD FRAMES are attached in a similar fashion to the Contour and Profile unit. The front and

rear pads can be removed by first lifting the roof assembly, and then lifting the pad assembly out;

the same way the Contour and Profiler work.

The SIDE PAD FRAMES are slightly different and involve the pad frame being rolled into the centre

of the unit and then being raised out. It is important that the pad frame is not forced, as this could

damage the alloy brackets.

The ROOF ASSEMBLY also remains the same as the Profiler/Contour units.

Some standard features differ between the Brivis Profiler, Contour and Advance.

Components

Brivis

Contour

Brivis

Profiler

Brivis

Advance

Motorised winter seal (Servoseal) Yes No No

Counter balanced weather-seal N/A Optional Optional

Motorised dump valve Yes Yes Optional

Aquasave Yes No No

Speed Sensor Yes Yes Yes

Networker compatible Yes Yes Yes

Water sensor Yes Yes Yes

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

5

BRIVIS

SERVICING

INSTRUCTIONS

Retrofitting the Service N-E5 to 0, 1 & 2 Series Contours.

The service N-E5 control can be used as a replacement control for all previous model coolers,

however some parameters need to be adjusted in order for the control to operate correctly. The

table below details all of the parameter adjustments that need to be made for each model cooler

when fitting an N-E5 into an older model Contour. These parameters are located in the cooler

service parameter section, and can only be accessed by using a Networker.

N-E5 parameter adjustments.

Parameter

number

Parameter description Default

setting

0 Series

Contour

1 Series

Contour

2 Series

Contour

3 Series

Contour or

Profiler

3 Series

Advance

05

Model selection number -

Determines min & max

fan speeds.

1

Check

specification

sheet

Check

specification

sheet

Check

specification

sheet

Check

specification

sheet

Check

specification

sheet

15

Flush count -

Number of refills before

flushing occurs.

20 20 20

20

Non Aquasave

250 Aquasave

20

Non Aquasave

250 Aquasave

20

22

Aquasave - Allows

N-E5 to power Aquasave

module.

1 = Enabled

0 = Disabled

0 0 0

0

Aquasave

powered by

pump power

supply.

1 – Contour

0 - Profiler

Advance - 0

43 Flush time -

Time

solenoid is open during flush.

200

sec

100

sec

60

sec

200

sec

200

sec

200

sec

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

6

BRIVIS

SERVICING

INSTRUCTIONS

No. 21

N-E5 Cooler Control Dump Delay Parameter.

Units affected:

All Version 3 Contours and Profiler coolers using N-E5 electronic controller.

Reason for change:

R&D have informed us of a change within the N-E5 service parameters. which has the potential to

cause a problem. This change has happened mid production and has affected the first 2020 units.

The problem has occurred to service parameter 01, which relates to the Dump Delay time. The

change is with the way the parameter is read. Usually the parameter unit was in single minutes, but

on the newer N-E5 controllers it has been changed to units of 10 minutes.

For example

- Normal setting was 60, meaning 60 minutes before the cooler would dump.

- New setting is 6, meaning 6 lots of 10 minutes which equals 60 minutes.

If service parameter 01 on the newer N-E5 is changed to 60 when we service these units, it

will then dump after 10 hours (60 x 10 minutes = 600 minutes). Vice Versa if Parameter 01 on

the first version N-E5 is set to 6, it will then dump after 6 minutes.

In both cases this will cause a fairly major upset with the units normal operation. We can trace the

individual controllers by their serial number. The first 2020 controllers have the dump delay setting

units in minutes, and the rest of the production controllers will all have the dump delay setting units

in lots of 10 minutes.

N-E5 Serial Numbers - 18764 020 0000 to 18764 020 2020 have the dump delay in single minutes.

N-E5 Serial Numbers - 18764 020 2021 and Beyond will have the dump delay setting in lots of 10

minutes.

N-E5 - Version 9, 9a & 10 will have the dump delay setting in lots of 10 minutes.

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

7

BRIVIS

SERVICING

INSTRUCTIONS

No. 23

N-E5 Cooler Control Upgrade

(This issue (2) replaces previous versions of servicing instruction #23 (issue 1))

Units affected: 3 Series Contours and Profilers.

Background: The version 7 N-E5 (original control) has proven to be unreliable, with the majority of

failures occurring with the Servo-seal action. The Version 8 N-E5 was introduced to fix this problem.

A tracking problem then started occurring on the trident water sensor. This coupled with lengthy fill

problems (software related) caused the units to operate OK for 2/3 hours before blowing hot air.

R&D have introduced the version 9 N-E5 control, which has had modifications done to the software.

This has improved the failure rate on the Servo-seal (further enhancement from the version 8), and

water level control problems, including refill times, have been rectified. Unfortunately the version 9

also suffered from Servo-seal failures, albeit few in number.

Root cause analysis has since proven that the cause of Servo-seal failures is due to power spikes

degrading PCB components. The version 9A is the latest N-E5 control, which has been upgraded to

protect components from power spikes. Field tests have already proven that the version 9A N-E5 is

very reliable.

The Version 9A controllers can be identified by the marking "9A" on the box.

Action: Technicians, when attending any 3 series cooler (Brivis Profiler or Contour), need to

complete these steps:

Identify the version of controller in the cooler and replace all N-E5 controls (version 7, 8 or 9) with

the new version "9A" controller. Version 8 controllers will be marked with an "8" on the box, and

version 9 controllers with a "9", while any version 7 and before will have no marking on the box.

Correctly label the control box with a defect sticker marked "TO BE REWORKED".

Test cooler for correct operation.

Complete your job sheet with the information below.

Documentation: These notes should be included on your POD invoice.

If the part failed before you attended the job-

Fault Part Fault Description

18764 2 Short description of the fault

If the part did not fail and was upgraded as per the Servicing instruction-

Fault Part Fault Description

18764 111 N-E5 Upgraded

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

8

BRIVIS

SERVICING

INSTRUCTIONS

No. 22

Trident Water Sensor Tracking Problems

Units affected: All Contours 1,2 & 3 Series, and Profiler 3 Series.

Background: It has been found in the field that the trident water sensor can be subject to false

sensing. This is caused by mineral build up behind the water sensor probes. The cooler may run for

a period of time before the fault occurs, but the fault will eventually result in the pump cavitating

because the unit has failed to fill. The build up on the probes forces the electronic controller to think

the water level is OK, when in actual fact it doesn't really know at what level the water is at.

Action: Service technicians are required to perform this action when attending any 3 series Contour

or Profiler. This action should only be performed on 1 or 2 series Contour coolers if they exhibit the

above symptoms. The installation of a modified water sensor should be carried according to the

installation instructions.

Plastic Housing Modified Sensor

Installation: Modifications have been made to Trident water sensor to help prevent this electrical

tracking on the water sensor. The plastic legs on the trident probe housing have been removed,

preventing any build up of minerals at the low point of the probes (see pictures).

Remove the old water sensor from the cooler trough and attach a defective label to part. This part

should be sent to warranty returns. if the unit is under warranty. If the unit is not under warranty this

part is to be charged to the customer.

Replace the water sensor with Part - 18066 - WATER SENSOR ASSY CONTOUR L1, ensuring

that the plastic housing has been modified (see picture above).

Test cooler for correct operation.

Documentation: These notes should be included on your POD invoice.

Fault Part Fault Description

18066 111 Modified water sensor.

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

9

BRIVIS

SERVICING

INSTRUCTIONS

Introduction of 5.5 litre ELBI solenoid

Background: On the 23/11/2004, the 5.5 litre ELBI solenoid was introduced into production for all 3

series Contours and Profilers. it was originally brought into production to try and prevent units from

failing to fill during a water limp error. it was found that the cause was not the limited flow (4 litre

ELBI) of the original solenoid but a water sensing issue. However the supplier of these solenoids

had already delivered 10,000 5.5 - litre solenoids, thus they were used in production.

Action: The introduction of the 5.5 litre solenoid is not expected to make any dramatic change to

the coolers operation. However there is a slight increase of water hammer occurring on the

premises. Tests conducted by our R&D department have proved that the hammer spike generated

by the 5.5 litre ELBI is no greater than our previous 12 litre soft close solenoid. Technicians can

identify the new 5.5 litre solenoid by a blue label that has been placed on the side of the solenoid

valve body.

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

10

Brivis Technical Data

Type: Technical Data Base Date Updated: 13/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 13

Sizing Guide Reference Figure 1000 - 1450

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 48.5 kg

Wet Weight 65.2 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 60 mm Rating 240 V / 50 Hz 10 Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

855BNVA-A12 Winding Resistance 206 Ohms (+/- 8% @ 20oC)

Watts 315 Overflow size 40 mm

Amps 2.4 Waste Outlet Size 40 mm

R.P.M. 1400 Tank Capacity 12 Litres

Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt

Blades 6 RPM 500

Blade Angle 23 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker NC-3

BWC-1 (Electronic)

BWC-2 (Manual)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

11

Brivis Technical Data

Type: Technical Data Base Date Updated: 13/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 23

Sizing Guide Reference Figure 1250 - 1800

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 49.5 kg

Wet Weight 67.3 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 75 mm Rating 240 V / 50 Hz 10 Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

855BNVA-A12 Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 315 Overflow size 40 mm

Amps 2.4 Waste Outlet Size 40 mm

R.P.M. 1400 Tank Capacity 12 Litres

Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt t

Blades 6 RPM 500

Blade Angle 23 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker N-C3

BWC-2 (Manual)

BWC-1 (Electronic)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

12

Brivis Technical Data

Type: Technical Data Base Date Updated: 13/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 33

Sizing Guide Reference Figure 1500 - 2250

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 51.5 kg

Wet Weight 70.4 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 90 mm Rating 240 V / 50 Hz 10 Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohms (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker N-C3

BWC-2 (Manual)

BWC-1 (Electronic)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

13

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 43

Sizing Guide Reference Figure 2000 - 2750

Cabinet detail

Width 1100 mm

Height front 800 mm

Height back 480 mm

Length 1100 mm

Dry Weight 54.5 kg

Wet Weight 75.0 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 90 mm Rating 240 V / 50 Hz 10Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker N-C3

BWC-2 (Manual)

BWC-1 (Electronic)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

14

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 53

Sizing Guide Reference Figure 2400 - 3200

Cabinet detail

Width 1100 mm

Height front 800 mm

Height back 480 mm

Length 1100 mm

Dry Weight 55.6 kg

Wet Weight 77.8 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 110 mm Rating 240 V / 50 Hz 10 Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker N-C3

BWC-2 (Manual)

BWC-1 (Electronic)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

15

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Contour L 63

Sizing Guide Reference Figure 2900 - 3600

Cabinet detail

Width 1100 mm

Height front 800 mm

Height back 480 mm

Length 1100 mm

Dry Weight 56.6 kg

Wet Weight 80.3 kg

Filter Pad Details Water Treatment Unit

Quantity 4 Type WE-1

Thickness 130 mm Rating 240 V / 50 Hz 10 Watt

Type CELDEK 5090 Amps 0.12

Air/Gas Flow Rate 1 L/minute minimum flow

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor ServoSeal Motor

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 Networker N-C3

BWC-2 (Manual)

BWC-1 (Electronic)

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

16

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Profiler P 23

Sizing Guide Reference Figure 1250 - 1800

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 47.0 kg

Wet Weight 64.8 kg

Filter Pad Details

Quantity 4

Thickness 75 mm

Type CELDEK 5090

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

855BNVA-A12 Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 315 Overflow size 40 mm

Amps 2.4 Waste Outlet Size 40 mm

R.P.M. 1400 Tank Capacity 12 Litres

Capacitor Size 8 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor Auto Refresh Tube

Size 538 mm Dia.. Type S.A.I.A

Type BRIVIS 538-6-23 Rating 240 V 50 Hz 0.23 Watt

Blades 6 RPM 500

Blade Angle 23 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 BWC-1 (Electronic)

BWC-2 (Manual)

Networker N-C3

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

17

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Profiler P 33

Sizing Guide Reference Figure 1500 - 2250

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 48.2 kg

Wet Weight 66.0 kg

Filter Pad Details

Quantity 4

Thickness 75 mm

Type CELDEK 5090

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 2 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor Auto Refresh Tube

Size 538 mm Dia.. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 BWC-2 (Electronic)

BWC-1 (Manual)

Networker N-C3

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

18

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Profiler P 43

Sizing Guide Reference Figure 2000 - 2750

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 49.0 kg

Wet Weight 67.9 kg

Filter Pad Details

Quantity 4

Thickness 90 mm

Type CELDEK 5090

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1250 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor Auto Refresh Tube

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 BWC-1 (Electronic)

BWC-2 (Manual)

Networker N-C3

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

19

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Profiler P 53

Sizing Guide Reference Figure 2400 - 3200

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 49.9 kg

Wet Weight 70.2 kg

Filter Pad Details

Quantity 4

Thickness 110 mm

Type CELDEK 5090

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor Auto Refresh Tube

Size 538 mm Dia.. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 BWC-1 (Electronic)

BWC-2 (Manual)

Networker N-C3

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Service Manual 32 – Contour 3 Series, Profiler & Advance – Approved Issue 5 Printed 2/13/2014 11:50:17 AM

20

Brivis Technical Data

Type: Technical Data Base Date Updated: 15/01/2004

Category: Specification Sheet - Cooler

Subject: Profiler P 63

Sizing Guide Reference Figure 2900 - 3600

Cabinet detail

Width 1100 mm

Height front 720 mm

Height back 400 mm

Length 1100 mm

Dry Weight 50.7 kg

Wet Weight 72.3 kg

Filter Pad Details

Quantity 4

Thickness 130 mm

Type CELDEK 5090

Duct Outlet Size

Width 550 mm

Length 550 mm

Pump / Water Distribution

Motor Pump Type ASKOLL M115

Type 240 V - 1 ph Pump Rating 240 V / 0.2 Amps

Model FASCO Pump Capacity 20 L/minute

80855BQVA-A22V Winding Resistance 206 Ohm (+/- 8% @ 20oC)

Watts 750 Overflow size 40 mm

Amps 4.9 Waste Outlet Size 40 mm

R.P.M. 1350 Tank Capacity 12 Litres

Capacitor Size 25 uF Distribution Hose Size 20 mm CLEAR HOSE

R.P.M Min Setting 500 Inlet Valve Type ELBI E.V Type 329

R.P.M Max Setting 1350 Inlet Valve Rating 240 V - 0.03 Amps

N-E5 Model Selection Model 1 Inlet Valve Capacity 4 L or 5.5L/minute

Coil Resistance 4.1 kOhm approx. @ 20oC

Inlet Valve Size 3/4" BSP (Male) Thread

Fan Impellor Auto Refresh Tube

Size 538 mm Dia. Type S.A.I.A

Type BRIVIS 538-11-30 Rating 240 V 50 Hz 0.23 Watt

Blades 11 RPM 500

Blade Angle 30 deg TIP Resistor 470 Ohm

Collet BRIVIS Capacitor 100 nF

Cooler Control Module Wall Controller

N-E5 BWC-1 (Electronic)

BWC-2 (Manual)

Networker N-C3

Water Connection

Flexible Hose Connection with 1/2" BSP (Male) Thread

Drain Connection

40 mm PVC

Page is loading ...

Brivis Contour User manual

This manual is also suitable for

Brivis Contour User manual

Related papers

Other documents