Airmar Technology Corporation DST810 User manual

Brand: Airmar Technology Corporation

Model: DST810

Type: User manual

This manual is also suitable for

DST810 CAST App



CAST

™

Application

Mobile App User Guide

Patent http://www.airmar.com/patent.html

for DST810 Multisensor

D-19219-rev.1 101321-rev.1 04/08/20

1



All Rights Reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied,

transmitted,disseminated,downloaded,orstoredinanystoragemedium,foranypurposewithoutpriorwritten

consentofAirmar.Airmarherebygrantspermissiontodownloadasinglecopyofthismanualandofanyrevisionof

thismanualontoaharddriveorotherelectronicstoragemediumtobeviewedandtoprintonecopyofthismanual

oranyrevisionhereto,providedthatsuchelectronicorprintedcopyofthismanualorrevisionmustcontainthe

completetextofthiscopyrightnoticeandprovidedfurtherthatanyunauthorizedcommercialdistributionofthis

manualoranyrevisionheretoisstrictlyprohibited.Informationinthismanualissubjecttochangewithoutnotice.

Airmarreservestherighttochangeorimproveitsproductsandtomakechangesinthecontentwithoutobligation

to notify any person or organization of such changes. Visit the Airmar website at www.airmar.com for current

updatesandsupplementalinformationconcerningtheuseandoperationofthisandotherAirmarproducts.



2



TABLEOFCONTENTS

WARNING……………………………………………………………………………………………………………………..............................................3

INTRODUCTION.............................................................................................................................................................4



GETTINGSTARTED.........................................................................................................................................................4

NAVIGATINGAIRMARCASTAPP...................................................................................................................................5

INITIALCONNECTIONTOYOURAIRMARSENSOR.....................................................................................................5

GENERALUSENOTES.................................................................................................................................................6

DEVICEDATAPAGE—DST810SMARTTRIDUCER......................................................................................................6

INFORMATIONPAGE.................................................................................................................................................7

Customization........................................................................................................................................................7

Units.......................................................................................................................................................................7

NMEA2000®PAGE....................................................................................................................................................8

OFFSETSPAGE.........................................................................................................................................................10

SPEEDCALIBRATION................................................................................................................................................11

BasicSpeedCorrection........................................................................................................................................12

SOGMethod....................................................................................................................................................12

DistanceMethod.............................................................................................................................................13

Heel‐CorrectedSpeedCalibration.......................................................................................................................15

SOGMethod....................................................................................................................................................15

DistanceMethod.............................................................................................................................................16

AdvancedSpeedCalibrationTable......................................................................................................................18





3





WARNING

Navigation Aid Only – The Airmar® CAST ™ app is intended only as a

navigationalaidandmustneverbeconsideredareplacementforcaution,

soundjudgementandpropernavigationalskill.Itisusedtoconfigureand

displaynavigationaldatafromindividualsensors.Theuserisresponsible

fortheaccuracyofthedatausedtocalibratetheconnectedsensor.Only

officialgovernmentchartsandNTMscontainallnecessaryinformation

forsafenavigation.Asalways,thecaptainisresponsiblefortheirprudent

useandsafetyofpassengersandcrew.

4



INTRODUCTION

TheAirmarCASTappisamobileapplicationthatallowsyoutoconnectto

yourAirmarSmartTRIDUCER.Youcanviewdata,adjusttheoutputs,

programoffsets,andcalibrateyourdevice.

CASTappcommunicatesdirectlywithyourAirmarDX900+orDST810

Multisensor;itreceivesonlythedataoutputbythesensor,notall

networktraffic.

GETTINGSTARTED

CASTappisavailableforiOSandAndroiddevicesandcanbedownloaded

fromtheAppleAppStoreorGooglePlayStore.

1. GototheAppStore(iOS)orPlayStore(Android)

2. Search“Airmar”anddownloadthefreeAirmarCASTapp.

3. EnsureBluetooth®isenabledonyourdevice.CASTappuses

BluetoothLowEnergy,whichdoesnotrequirepairing.Theapp

willautomaticallysearchfordeviceswithinrange,sothere’sno

needtoopenyourdevice’sBluetoothmenu.

4. OpentheAirmarCASTapp. 

AllcompatibleAirmardeviceswithinrangewillbedisplayedonthe

devicelist.Selectyourdevicefromthelisttoconnect.

Note:Makesureyou’reascloseaspossibletothedevicewhiletryingto

connect.TheBluetoothantennainaDST810isneartheprintedcap,but

therearemanythingsonaboatthatcanattenuateaBluetoothsignal.

Largeobjectslikefueltanksorbulkheadscanaffectthesignalstrength.

WaterwillalsoblockaBluetoothsignal,somakesurethedeviceisn’t

submerged.



5



NAVIGATINGAIRMARCASTAPP

INITIALCONNECTIONTOYOURAIRMARSENSOR

Oncepoweredon,theDST810willbroadcastanannouncementmessage

withoutanyfurtherinput.SimplyopentheAirmarCASTapponyour

phoneortablettoseealistofdeviceswithinrange.Thereisnoneedto

“pair”withthedevice.

Thedevicesearchpageintheappwillshowalistoftheavailablesensors.

Ifyouhaveneverconnectedtoaspecificsensorbefore,itwillbenoted

byitsmodel,suchasDST810,withanicontoshowsensortype.Ifyour

phoneortablethasconnectedtoanavailablesensorbefore,itwill

displayyourcustomizedfriendlynameandtheserialnumberinthetile.

Seepage7formoreinformationoncustomization.

Note:Tryingtomaketheinitialconnectiontoyourdeviceinacrowded

area,suchasamarina,canbedifficult.Makesureyou’reconnectingto

yourdeviceandnotanearbysensorthatisalsopoweredon.Ifmultiple

sensorsarepresentontheDeviceSearchpage,movetoalesscrowded

locationtoperformtheinitialconnection.

Tapyoursensoronthelisttostarttheconnection.Thefirsttimeyou

connect,theappwillaskyoutoenterthelastthreedigitsofthedevice’s

serialnumber.Theserialnumbercanbefoundonthewarrantylabel

affixedtothecablenearthesensor.Ifthelabelisnotreadilyaccessible,

theserialnumberisavailableontheNMEA2000networkthrougha

connectedMFDorinstrumentdisplay.

Youwillonlyneedtoverifytheserialnumberonthefirstconnection.If

youconnectfromanotherdeviceordeleteandreinstalltheAirmarCAST

apponyourphone,you’llneedyourserialnumberagain,sobesureto

recordandsaveitifthelabelisn’treadilyaccessible. 

6



GENERALUSENOTES

ManyvaluesintheAirmarCASTappcan

beadjustedbytheuser.Anyvaluethatis

underlinedcanbeadjusted.Tapthe

valuetoopenthekeypadandmakean

adjustmentordeletetheexistingvalue.

Whenenteringtable

values,tapthecell

valuetoopenthe

keypadandmakean

adjustment.Tapthe

headingoftherowor

columntoadjustthevaluein

thecellordeletetheroworcolumnaltogether.

Toenteranegativevalueusingthekeypad,enterthe

valueasapositivenumberfirst,thentapthe“+/‐“

buttoninthelowerleftcornertochangethesign.

DEVICEDATAPAGE—DST810SMARTTRIDUCER

Onceconnectedtoyourdevice,theCASTappwilldisplaythedata

availablefromthedevice.TheDST810willdisplayDepth(below

transducer),Speed(speedthroughwater),andTemperature(water

temperature).Asingletapanywhereonthescreenwillchangetheview

fromgraphictotext.

Bydefault,attitude(heelandtrim)outputisturnedoff.

Adatafieldthatdisplays“‐“iseitherdisabledorisnotreturningavalid

value.IfDepthdoesnotdisplayanumber,ensuretheurethanefaceof

thesensorisincontactwiththewater.Ifthewaterdepthisgreaterthan

themaximumrangeofthesensor,nodepthwillbereturnedand“‐“will

bedisplayed.

Thespeedometerviewwillshowaninitialrangeof0–15kn(thisrange

willbeadjustedbasedontheunitsselected).Asthespeedincreases,the

rangeofthespeedometerwillautomaticallyadjusttoensurethespeedis

alwayseasilyreadable.

Note:Ifapositivedepthoffsethasbeensavedtothesensor,theCAST

appwilldisplay“DepthBelowSurface.”Iftheoffsetsavedhasanegative

value,theCASTappwilldisplay“DepthBelowKeel.”SeetheOffsets

sectiononpage10formoreinformation.



7



INFORMATIONPAGE

SelecttheInformationtabtodisplayinformationontheconnected

device.

Theserialnumberisuniquetotheconnecteddevice.

ThepartnumberistheAirmarpartnumberforconnecteddevice.

Thecurrently‐installedfirmwareversionisdisplayednext.Takenoteofall

firmwareversionsforanytechnicalinquiries.

CUSTOMIZATION

ThefirsttimeyouconnecttoyourDST810,thedevicewillbedisplayed

simplyas“DST810”inthesearchmenu.Thisdisplaynamecanbe

adjustedusingthe“Customize”button.

Selecttheicondisplayedontheheel/trimgaugeandentera“Friendly

Name”fortheDST810.Thisname,alongwiththedevice’sserialnumber,

willbestoredonyourdevice.Thenexttimeyouconnecttothedevice,

themenuwillshowthedeviceusingtheFriendlyNameandthedevice’s

serialnumber.

Note:TheserialnumberandFriendlyNamearestoredlocallyinthe

AirmarCASTapp,notwithinthesensor.Ifyouconnecttothesensorusing

adifferentsmartphone,theFriendlyNamewillnotbedisplayeduntilyou

connectandnamethedevice.EnteringaFriendlyNamewillnotaffect

namesalreadysavedonothersmartphones.

UNITS

Onceconnectedtoadevice,youcanadjustthedisplayunitsbytapping

thegearicon atthetoprightcornerofthescreen.Unitsfor

speed,depth,temperature,anddistancecanbeselectedindividually.For

example,speedcanbedisplayedinmilesperhourwhiledistanceis

displayedinnauticalmiles,orviceversa.





8



NMEA2000®PAGE

TheNMEA2000pagedisplaysallthePGNstheconnecteddeviceis

capableofsupplyingtothenetwork.

Bydefault,eachitemwilldisplaythenameofthePGNandtheNMEA

2000PGNnumber.IfthePGNisdisabled,“Off”isdisplayed.IfthePGNis

enabled,theoutputratewillbedisplayed.



OutputratesareshownasanumberofPGNsperunittime.Forexample,

iftheWaterDepth(128267)PGNdisplays“1/sec,”thePGNisenabled

andwillbeoutputtothenetworkonetimeeachsecond.If“2/min”is

displayed,thePGNwillbeoutputtothenetworktwotimesperminute,

oronceevery30seconds.

Usethe“arrow”buttonontherightsideofeachitemtoexpanditand

enable/disableoradjusttheoutputrate.

TheswitchatleftwillenableordisablethePGNoutput.

ThedropdownmenuatrightwillallowyoutoadjustthePGNoutput

rate.

Note:ChangingthePGNoutputoroutputratewillnotchangethe

internaldatacalculationrate.



9



DisablingaPGNusingtheswitchwillpreventdatafrombeingsenttothe

network,butitwillnotpreventthesensorfromcalculatingavalue

internally.

Forexample,disablingtheDepth(128267)PGNwillpreventdepth

informationfrombeingprovidedtothenetwork,butitwillnotstopthe

sensorfrompingingfordepth.



10



OFFSETSPAGE

OffsetscanbeprogrammedforDepth,Temperature,andTrim,andHeel.

Anoffsetisanadditivevalue.Settinganoffsetwilladdto(orsubtract

fromiftheoffsetisnegative)thevaluemeasuredbythesensor.The

unadjustedvaluemeasuredbythesensorislistedas“Raw.”Tapthe

underlined“Offset”valuetoadjusttheoffset.Enteranegativevalueto

subtractfromtherawvalueorapositivenumbertoadd.

Forexample,ifthekeelextends1footdeeperthanthefaceofthe

transducer,enteravalueof‐1asadepthoffsettodisplay“DepthBelow

Keel.”1willbesubtractedfromeverydepthmeasurementtakenbythe

sensorbeforeitissenttothenetwork.Everydeviceonthenetworkwill

seetheadjusteddepthbelowkeel.

Temperatureoffsetsworksimilarlytodepthoffsets.



Heelandtrimcanbecalibratedusinganoffsetaswell.Theoffsetin

degreesisaddedtotherawvaluefromthesensor.

Ifnooffsetshavebeenprogrammed(0degreesforbothheelandtrim),

theappwillpromptyoutocalibratethesensor.Thiscanbedoneinone

oftwoways.”

Toautomaticallycalibrateheelandtrim,makesuretheboatisrelatively

stationary.Pressandholdthecirclemarked“HoldtoCalibrate.”Theapp

willbegintocalculateanaveragepitchandrollreadingover10seconds

andanorangebarwilldisplaytheprogress.Oncethebarflashesgreen,

theaveragereadingforbothheelandtrimwillautomaticallypopulate

theoffsetfieldsandthesensorshouldreadapproximately0degrees

under“Value”forbothheelandtrim.Remember,thecalculationusesan

average,soanymovementoverthemeasurementperiodwillimpactthe

finalnumber.

Alternatively,thevaluescanbemanuallyprogrammed.Forexample,if

therawheelvalueis17.8degrees,enteringanoffsetof‐17.8willresult

inareportedvalueof0degrees.



11



SPEEDCALIBRATION

Unlikeoffsets,whichareadditive,basicspeedcompensationvaluesare

enteredaspercentagesandaremultiplicative.A10%speed

compensationwillresultina10%increaseinthereportedspeedacross

allvalues.

Forexample,a10%speedcompensationwillresultinanoutputof11kn

(+1kn)whenthepaddlewheelmeasuresarawvalueof10knandan

outputof22kn(+2kn)whentherawmeasuredvalueis20kn.

Thewaterflowprofileunderthehullofyourboathasalargeaffecton

thereadingofthespeedsensor.Manyvariables,includingtheshapeof

thehull,theroughnessofthesurface,thepositionofstrakes,etc.will

changetheattachedflowprofile.Seethetransducer’sinstallationguide

forinformationonwheretoinstallthesensorinthehulltoensure

accuratespeedanddepthperformance.Evenwhenthesensoris

correctlyinstalled,it’simportanttocalibrateyourpaddlewheelatits

installationlocationandundernormalusetomakesureitdeliversthe

bestpossibleperformance.

Calibratingspeedbytravelingaknowndistanceisacommonmethodof

calibration,butthestartandendpointsaretypicallyfixedtotheground

andasinglerundoesnottakeintoaccountthemovementofthewater

current.

CalibratingdirectlytorawGPSspeedovergroundcanalsoresultinan

inaccuratecalibration.Iftheboatistravelingina3kncurrentinthe

directionofmovement,theGPSSOGwillbe3knfasterthantheactual

speedthroughwater.

TheAirmarCASTappallowsyoutoquicklycalibratespeedandcorrectfor

current.Youcanalsocorrectthespeedcalibrationforchangesintheflow

beneaththehullthatoccurwhentheboatisheeledovertoonesideor

theother.

ThereareseveralmethodsofspeedcalibrationusingtheCASTapp.



12



BASICSPEEDCORRECTION

Thesimplestwaytocalibratespeedisasinglepointpercentageoffset.

Thistypeofcalibrationappliesafixedpercentagecorrectiontoevery

readingfromthepaddlewheel.

NavigatetotheSpeedCalibrationtab.Bydefault,thespeedcalibrationis

setto“OFF.”

Enablethe“BASIC”speedcalibration.

Ifthedesiredpercentageadjustmentisknown,youcansimplyenterit

intotheCompensationfield.

Ifyouwouldliketheapptocalculatethecorrectpercentageadjustment

foryou,tapthewizardicon.



CASTappcancalculatethepercentageusingoneoftwomethods.

 SOG:SpeedthroughwateriscalculatedusingaGPSreference

speedoverground.

 Distance:Speedthroughwateriscalculatedusingtraveltime

overaknowndistancesuchasameasuredmile.



SOGMETHOD

TheSOGmethodallowstheapptocalculateyouraveragespeedover

groundusingtheinternalGPSinyoursmartdevice.Youcanalso

manuallyenteranaveragevaluefromanexternalsource.

Bringtheboatuptocalibrationspeed.Thisisthespeedwhereyouwant

thegreatestaccuracyinyourspeedreadingandwillbedifferentforeach

boat.

Oncetravelingatarelativelyconstantspeedanddirection,tapthe

“Primary”button.Theappwillcountdownasitcalculatesanaverage

indicatedspeedfromthepaddlewheelandanaverageGPSSOG.



13



Oncecomplete,theaverageforeachvaluewillbeshownandthe

“Primary”buttonwillchangeto“Reverse.”

Turntheboat180degreesandbringitbacktoapproximatelythesame

speedusedintheprimarydirection.Youdon’tneedtoholdexactlythe

samespeedfromtheprimaryrun,butthecloser,thebetter.Maintaina

consistentspeedanddirection.

Tap“Reverse”andwaitfortheapptocountdownwhiletheaverage

speedsarecalculated.Thesecondrunintheoppositedirectionallows

theapptocalculatethespeedofthecurrentinthewaterandremoveit

fromthecalibration.

Oncecomplete,theappwilldisplaythecalculatedpercentage

adjustment.Tap“Apply”tosavethevalue.

Thespeedcorrectionvaluehasnowbeencalculatedandsavedto

memoryintheDST810.Itwillbeappliedtoallspeedvaluessenttothe

networkandtransmittedwirelesslytotheapp.Alldevicesconnectedto

theNMEA2000networkwilldisplaytheadjustedvalue.

ThevaluecanbemanuallyadjustedbytappingthevalueontheSpeed

Calibrationscreen.



DISTANCEMETHOD

ThedistancemethodofspeedcalibrationwillnotmakeuseofGPS.

Instead,you’lltravelaknowndistanceatarelativelyconstantspeed.The

appwillcalculatetheaveragespeedtraveledusingthetimerequiredto

covertheknowndistance.Itwillalsocalculatetheaverageindicated

speedfromthepaddlewheelandcomparethetwo.

Note:Calibrationusingaknowndistancerequiresbothanaccurate

measurementbetweentworeferencepointsandanaccuratetimeto

travelbetweenthem.Theshorterthedistancebetweenpoints,themore

potentialthereisforerrorinthemeasurement.Aminimumdistanceof

onestatutemileisrecommendedforadistance‐basedspeedcalibration.

Selectthe“Distance”button.

Entertheknowndistancebetweentwopointsintheunitsindicated.

Bringtheboatuptocalibrationspeed.Thisisthespeedwhereyouwant

thegreatestaccuracyinyourspeedreadingandwillbedifferentforeach

boat.



14



Whenyoupassthestartpoint,tap“Start.”Theappwillbegincountingin

seconds.

Whenyoupasstheendpoint,tap“Stop.”Thenumberofrunswill

increasebyoneandthecalculatedspeedswillbeshown.

Thenumberofrunsalreadycompletedwillbeshownas“Completed

Runs.”“TotalTime”isacountofthetotalnumberofsecondsforallruns.

“RunSpeed”showstheaveragerecordedpaddlewheelspeedonthelast

run,while“Speed”showstheoverallaverage.“RunCorrection”isthe

correctionfactorcalculatedonthepreviousrun,and“Correction”isthe

overallaveragecorrectionfactorcalculated.

Followthesameprocessforadditionalruns.Ifyouwouldliketothrowa

runout,tap“DiscardRun”oncecompleteandtryagain.

Note:Ifyou’reperformingthecalibrationinalocationwhereasignificant

currentmaybepresent,makesuretoperformanevennumberofruns

withhalfinonedirectionandhalfreturningintheoppositedirection,as

closeto180degreesaspossible.Thiswillensurethecalculatedaverage

accuratelyaccountsforthecurrent.

Oncecomplete,tap“Apply”tosavethevalue.

Thespeedcorrectionvaluehasnowbeencalculatedandsavedto

memoryintheDST810.Itwillbeappliedtoallspeedvaluessenttothe

networkandtransmittedwirelesslytotheapp.Alldevicesconnectedto

theNMEA2000networkwilldisplaytheadjustedvalue.

ThevaluecanbemanuallyadjustedbytappingthevalueontheSpeed

Calibrationscreen. 

15



HEEL‐CORRECTEDSPEEDCALIBRATION

Note:MakesuretheattitudePGNisenabledontheNMEA2000page.

Onceenabled,makesurethesensorhasbeencalibratedwiththeboat

stationary.RefertotheOffsetsPagesectionformoreinformationabout

calibrationoftheattitudesensor.Heel‐correctedSpeedCalibrationand

theAdvancedCalibrationTablecannotbeusedwithoutattitudeenabled.

Changesinheelangleoftheboatwhileunderwaycanaffectthespeed

calculatedbythepaddlewheel.TheDST810canstorecalibrationsatup

totwodifferentanglesoneachsideinadditiontothestandard

calibration.Inordertoapplyaspeedcalibrationatmorethanoneangle,

theadvancedtablemustbeused.

Astheheelangleoftheboatchanges,thesensorwillshiftfromone

curvetothenext,interpolatingbetweenthem.

Forexample,ifa15%compensationisappliedat10degreesofheeland

a5%compensationisappliedat0degrees,thesensorwillapplya10%

compensationat5degreesofheel.

Heel‐correctedSpeedCalibrationsareappliedusingasimilarprocessas

theStandardCalibration.However,thenatureoftheprocessprevents

makingrunsinoppositedirections.Forthisreason,it’simportantto

performthecalibrationinslackwater.

BeginthecalibrationbyselectingthewizardiconontheHeel‐corrected

SpeedCalibrationwindow.LiketheStandardCalibration,theHeel‐

correctedSpeedCalibrationcanbeperformedusingtwomethods.

 SOG:SpeedthroughwateriscalculatedusingaGPSreference

speedoverground.

 Distance:Speedthroughwateriscalculatedusingtraveltime

overaknowndistancesuchasameasuredmile.



SOGMETHOD

TheSOGmethodallowstheAirmarCASTapptocalculateyouraverage

speedovergroundusingtheinternalGPSinyoursmartdeviceor

manuallyenteranaveragevaluefromanexternalsource.

Bringtheboatuptocalibrationspeed.Thisisthespeedwhereyouwant

thegreatestaccuracyinyourspeedreadingandwillbedifferentforeach

boat.



16



Choosetheangleatwhichyouwouldliketoperformthecalibration.

Makesureyoucanmaintaintheangleofheelenteredinbothdirections;

thesameangleisusedforbothportandstarboard.Theappwill

automaticallyrecognizeaportorstarboardtack;there’snoneedto

specifytherun,onlytomaintainasclosetotheselectedangleas

possible.

Oncetravelingatarelativelyconstantspeed,direction,andheelangle,

tapthe“Primary”button.Theappwillcountdownasitcalculatesan

averageindicatedspeedfromthepaddlewheelandanaverageGPSSOG.

Theappwillnotpromptforasecondrunasthisisoftennotpossible.It’s

importantthiscalibrationberuninslackwater.

Oncecomplete,theappwilldisplaythecalculatedpercentage

adjustmentforthesidetowhichtheboatwasheeled.Performthesame

processagaintoaddacalibrationfortheoppositeside,andkeepinmind

thetwowillfrequentlybedifferent.Tap“Apply”tosavethevalue.

Thespeedcorrectionvaluehasnowbeencalculatedandsavedto

memoryintheDST810.Itwillbeappliedtoallspeedvaluessenttothe

networkandtransmittedwirelesslytotheapp.Alldevicesconnectedto

theNMEA2000networkwilldisplaytheadjustedvalue.

ThevaluecanbemanuallyadjustedbytappingthevalueontheSpeed

Calibrationscreen.

DISTANCEMETHOD

ThedistancemethodofspeedcalibrationwillnotmakeuseofGPS.

Instead,you’lltravelaknowndistanceatarelativelyconstantspeed.The

appwillcalculatetheaveragespeedtraveledusingthetimetocoverthe

knowndistance.Itwillalsocalculatetheaverageindicatedspeedfrom

thepaddlewheelandcomparethetwo.

Note:Calibrationusingaknowndistancerequiresbothanaccurate

measurementbetweentworeferencepointsandanaccuratetimeto

travelbetweenthem.Theshorterthedistancebetweenpoints,themore

potentialthereisforerrorinthemeasurement.Aminimumdistanceof

onestatutemileisrecommendedforadistance‐basedspeedcalibration.

Selectthe“Distance”button.

Entertheangleatwhichyouwouldliketocalibrateandtheknown

distancebetweentwopointsintheunitsindicated.



17



Bringtheboatuptocalibrationspeedandtheselectedheelangle.Thisis

thespeedwhereyouwantthegreatestaccuracyinyourspeedreading

andwillbedifferentforeachboat.

Whenyoupassthestartpoint,tap“Start.”Theappwillbegincountingin

seconds.

Thenumberofrunsalreadycompletedwillbeshownas“Completed

Runs.”“TotalTime”isacountofthetotalnumberofsecondsforallruns.

“RunSpeed”showstheaveragerecordedpaddlewheelspeedonthelast

run,while“Speed”showstheoverallaverage.“RunCorrection”isthe

correctionfactorcalculatedonthepreviousrun,and“Correction”isthe

overallaveragecorrectionfactorcalculated.

Followthesameprocessforadditionalruns.Ifyouwouldliketothrowa

runout,tap“DiscardRun”oncecompleteandtryagain.

Note:Ifyou’reperformingthecalibrationinalocationwhereasignificant

currentmaybepresent,makesuretoperformanevennumberofruns

withhalfinonedirectionandhalfreturningintheoppositedirection,as

closeto180degreesaspossible.Thiswillensurethecalculatedaverage

accuratelyaccountsforthecurrent.

Oncecomplete,tap“Apply”tosavethevalue.Theappautomatically

detectsthedirectionofheelandpopulatesthecorrectfield.

Thespeedcorrectionvaluehasnowbeencalculatedandsavedto

memoryintheDST810.Itwillbeappliedtoallspeedvaluessenttothe

networkandtransmittedwirelesslytotheapp.Alldevicesconnectedto

theNMEA2000networkwilldisplaytheadjustedvalue.

ThevaluecanbemanuallyadjustedbytappingthevalueontheSpeed

Calibrationscreen.



18



ADVANCEDSPEEDCALIBRATIONTABLE

Note:Theadvancedspeedcalibrationtablewilloverrideanyother

programmedspeedcorrections.Itwillnotbeaddedontopoftheexisting

speedcalibration.Beforeswitchingtotheadvancedcalibrationtable,

makesuretocarefullyquantifytheperformanceofthesensorwithout

anycorrectionsinplace.

TheAdvancedSpeedCalibrationTableallowsfineadjustmentofspeed

correctionovermultiplespeedsandangles.

Uptotwoanglespersidecanbeselected.

Upto10non‐zerospeedscanbeaddedtothetable.

Note:Whenusingtheadvancedcalibrationtable,makesurethehighest

speedinthetableisthefastestspeedthevesselwilltypicallyachieve.If

thespeedexceedsthelargestvalueinthetable,thesensorwillapplya

linearcorrectionofthesameslope.Thiscanloseaccuracyquicklyifthe

lastspeedisverylow.It’simportantthetableincludetheentirerangeof

achievablespeedsregardlessofthenumberofindividualpoints.

Tousetheadvancedspeedcalibrationtable,first

switchspeedcalibrationto“Off.”

Eithermanuallyorusing3

partysoftware,collect

thedifferencebetweenindicatedspeedandactual

speedthroughwaterateachcalibrationpoint.

Thetableisorganizedwithspeedsshownas

columnsandheelanglesshownasrows.Eachcellis

thespeedcorrection(inunitsofspeed,suchas

knots,mph,etc.)appliedtothatspecificheelangle

andspeedcombination.

EnabletheAdvancedSpeedCalibrationTableonthe

SpeedCalibrationTab.Expandthetabletothedesirednumberofrows

andcolumns.Inputthedifferencesmeasuredpreviously.Forexample,if

at0degreesofheeland8knindicatedspeedtheactualspeedthrough

waterwasmeasuredat8.5kn,enter0.5inthatcell.Iftheactualspeed

throughwaterwasmeasuredat7.5kn,enter‐0.5inthatcell.

Makesuretofilloutthetablecompletely.Removeanyunusedrowsand

columnsbyselectingtheheadingandtappingtheX.Theadvancedtable

doesnotadjustthebasicspeedcalibrations;itisastandalonemethodof

speedcalibrationthatoverridestheothers.InaccurateindicatedSTWwill

resultifthetableisnotcompletelyfilledin.



19



Makesuretosavearecordofthetableasentered.Becausethe

advancedspeedsettingsoverrideallothers,thetablewillbedeletedif

youreturntotheBasicCalibrationsettings.Thetablewillneedtobe

reenteredifyoureturntotheAdvancedCalibrationTable.

Thespeedcalibrationtabswillnotappearwhenthedeviceisin

landscapemode—turnbacktoportraitaspecttodisplaythetabsandexit

theadvancedcalibration.

Note:Makesuretokeeparecordofthedataintheadvancedtable.As

longasthetableisactive,thedataaresavedtomemoryintheDST810.If

theAdvancedSpeedtableisdisabledbyswitchingbacktoBasicorOff,

thedatainthetablewillbepermanentlydeleted.



Page is loading ...

Airmar Technology Corporation DST810 User manual

Brand: Airmar Technology Corporation

Model: DST810

Type: User manual

This manual is also suitable for

DST810 CAST App

Download PDF

report

Airmar Technology Corporation DST810 User manual

This manual is also suitable for

Airmar Technology Corporation DST810 User manual

Related papers

Other documents