Crestron TSW-750 Quick start guide
- Category
- Touch screen monitors
- Type
- Quick start guide
quickstart guide
TSW-750
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TSW-750
7” Touch Screen
The Crestron® TSW-750 touch screen installs into a standard 2-gang or 3-gang U.S electrical box or a
2-gang European electrical box. It can also be attached directly to drywall and other surfaces over the
front of a 2 3/8” (60 mm) high by 3 3/8” (86 mm) wide cutout. When installed, it protrudes just 1/2”
(13 mm) from the mounting surface and magnetically adheres to its included mounting bracket.
It is supplied with screws for installation.
1 Install the Touch Screen
QUICKSTART DOC. 7325F (2033254, Sheet 1 of 2) 05.13
1
To mount the TSW-750 into an electrical box, use the following procedure:
1. Use four of the eight included screws (four #06-32 x 3/4” or four 3 x 16 mm) to attach the mounting
bracket (2031833) to the electrical box, as shown in the following illustrations.
For U.S.-style installations, use the #06-32 x 3/4” screws (2033247).
For European-style installations, use the 3 x 16 mm screws (2013788).
Mount the TSW-750 into a U.S. Electrical Box
2. When making connections to the TSW-750, use Crestron power supplies for Crestron equipment.
Apply power after all connections have been made.
3. Carefully position the touch screen over the mounting bracket and gently place it in position.
The magnets on the rear of the touch screen hold it in place on the mounting bracket.
Hardware Connections for the TSW-750
Mount the TSW-750 into a European Electrical Box
NOTE: The included cable mount ferrite bead, FBTH-2
(2033216) should be placed on the LAN cable in the
electrical box.
For Regulatory Compliance information, refer to the latest
version of Doc. 7326.
Reset Button
LAN PoE :
10 BASE - T / 100 BASE - TX
Ethernet to LAN
NOTE: For U.S.-style installations, use a #2 Phillips screwdriver. For European-style installations,
use a #1 Phillips screwdriver or equivalent.
TSW-750
U.S. Electrical Box
Mounting Bracket
(2031833)
Screws (4) #06-32 x 3/4”
(2033247)
Screws ( 4 ) 3 x 16 mm
( 2013788 )
TSW - 750
European Electrical Box
Mounting Bracket
( 2031833 )
NOTE: For proper positioning of the touch screen unit, the electrical box or cutout must be positioned
approximately 1/4 inch (6 mm) to the right of center and 1/10 inch (3 mm) above center.
quickstart guide
TSW-750
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TSW-750
7” Touch Screen
QUICKSTART DOC. 7325F (2033254, Sheet 1 of 2) 05.13
2
2 Establish Communication
Use Crestron Toolbox™ for communicating with the TSW-750; refer to the Crestron Toolbox help
file for details.
There is a single method of communication: TCP/IP communication.
Ethernet Communication
NOTE: During regular operation of the touch screen,
there are two ways to activate the setup functions:
1. Place a button on the project main page and assign
the reserved join number (17242) that activates setup.
2. Touch “hard keys” 1, 2, 3 and 4, to the right of the
touch screen display, in sequence twice (touch
1, 2, 3, 4, 1, 2, 3, 4) within a five second period.
When power is applied for the first time, the screen
shown in the illustration to the right appears.
3 Configure the Touch Screen
NOTE: The only connection required to configure the touch screen is power.
Refer to step 2 in section
➊
“Install the Touch Screen” for details.
Touch the Setup button to display the TSW-750 main
“Setup” menu, as shown in the illustration to the right.
The setup screens enable basic configuration procedures
prior to regular operation of the TSW-750.
NOTE: For details on configuring the TSW-750, refer to
the latest version of the TSW-750 Configuration Guide
(Doc. 7366). It is available from the Crestron Web site
(www.crestron.com/manuals).
For Regulatory Compliance information, refer to the latest
version of Doc. 7326.
NOTE: The TSW-750 can take up to 45 seconds to boot to a display after initial power up.
4
3
2
1
PC Running
Crestron Toolbox
LAN
Power
Injector
CRESTRON
CEN-SW-POE-5 Power over Ethernet Switch
Uplink
PoE
1234
48VDC
Power
120 Volts
POE
TSW-750
The TSW-750 connects to PC via Ethernet:
1. Use the Device Discovery Tool (click the icon) in Crestron Toolbox to detect all Ethernet
devices on the network and their IP configuration. The tool is available in Toolbox version
1.15.143 or later.
2. Click on the TSW-750 to display information about the device.
quickstart guide
TSW-750
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TSW-750
7” Touch Screen
QUICKSTART DOC. 7325F (2033254, Sheet 2 of 2) 05.13
3
4 Dimensions
TSW-750 Overall Dimensions (Top View)
TSW-750 (Bottom View)
5 Pinout Reference
The only connector on the TSW-750 is the LAN PoE port.
LAN PoE
PIN DESCRIPTION
1
2
3
4
5
6
7
8
TX +
TX -
RX +
DC -
DC -
RX -
DC +
DC +
Pin 8 Pin 1
For Regulatory Compliance information, refer to the latest
version of Doc. 7326.
6Recommended Cleaning
Keep the surface of the touch screen free of dirt, dust or other materials that could degrade optical
properties. Long-term contact with abrasive materials can scratch the surface, which may detrimentally
affect image quality.
For best cleaning results, use a clean, damp, non-abrasive cloth with any commercially available
non-ammonia glass cleaner. Bezels may not provide a complete watertight seal. Therefore, apply
cleaning solution to the cloth rather than the surface of the touch screen. Wipe touch screen clean and
avoid getting moisture beneath the bezels.
7 . 59 in
( 193 mm )
5 . 98 in
( 152 mm )
4 . 74 in
( 121 mm )
3 . 58 in
( 91 mm ) 2 . 24 in
( 57 mm )
0 . 47 in
( 12 mm )
2 . 03 in
( 52 mm )
Microphone
TSW-750 Overall Dimensions (Front and Side Views)
3 . 36 in
( 86 mm )
Speakers
quickstart guide
TSW-750
www.crestron.com
888.273.7876 201.767.3400
Specifications subject to
change without notice.
TSW-750
7” Touch Screen
Connectors
LAN PoE: (1) 8-wire RJ-45 with 2 LED indicators
10Base-T/100Base-TX Ethernet port, Power over Ethernet compliant
Green and yellow LEDs indicate Ethernet port status
Power Requirements
Power over Ethernet: IEEE 802.3af (802.3at Type 1) Class 3 PoE Powered Device
Environmental
Temperature: 32° to 112°F (0° to 45°C)
Humidity: 10% to 90% RH (non-condensing)
Heat Dissipation: 44 Btu/h
Enclosure
Construction: Plastic, smooth black or white finish
Mounting: Surface mount over a 2 or 3-gang electrical box, 2-Gang European (DIN 49073) electrical box,
or 2-3/8” H x 3-3/8” W (60mm H x 86mm W) cutout2; optional tabletop kit sold separately
Dimensions
Height: 4.74 in (121 mm)
Width: 7.59 in (193 mm)
Depth: 2.03 in (52 mm)
Weight
15 oz (400 g)
NOTES
1. Supports Smart Graphics only. Not compatible with “traditional” UI projects.
2. For proper positioning of the touch screen unit, the electrical box or cutout must be positioned approximately
1/4 inch (6 mm) to the right of center and 1/10 inch (3 mm) above center.
7 Specifications
QUICKSTART DOC. 7325F (2033254, Sheet 2 of 2) 05.13
4
The specific patents that cover Crestron products are listed at patents.crestron.com.
Crestron, the Crestron logo, Crestron Toolbox, Rava and Smart Graphics are either trademarks or registered trademarks of
Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks and trade names
may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims
proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2013 Crestron Electronics, Inc.
For Regulatory Compliance information, refer to the latest
version of Doc. 7326.
Touch Screen Display
Display Type: TFT active matrix color LCD
Size: 7 inch (178 mm) diagonal
Aspect Ratio: 15:9 WVGA
Resolution: 800 x 480 pixels
Brightness: 300 nits (cd/m2)
Contrast: 350:1
Color Depth: 18-bit, 262k colors
Illumination: Edgelit LED
Viewing Angle: ±70° horizontal, ±65° vertical
Touch Screen: Projected capacitive
Buttons
Hard Keys: (5) Projected capacitive push buttons, programmable, pre-labeled with icons for “Power”, “Home”,
“Lights”, “Up”, and “Down”
Reset: (1) Miniature push button on rear panel for hardware reset
Memory
LPDDR2 RAM: 1 GB
Flash: 4 GB
Maximum Project Size: 512 MB
Graphics Engine
Supports Smart Graphics™ 1
Communications
Ethernet: 10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3af and
802.3at Type 1 compliant
Video
Streaming Formats: H.264 (MPEG-4 part 10 AVC), MJPEG
Audio
Features: Built-in microphone and speakers, Rava™ SIP Intercom
Audio Feedback Formats: MP3
-
1
-
2
-
3
-
4
Crestron TSW-750 Quick start guide
- Category
- Touch screen monitors
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI