F-14B TOMCAT
KIT 5525 85552500200
Gray
Light Gray
Gunship Gray
Olive Green
Insignia Blue
Semi Gloss White
Flat Yellow
Aluminum
Silver
Steel
Gloss Red
Gloss Green
Semi Gloss Black
Flat Black
Medium Gray
Medium Dark Gray
* REPEAT SEVERAL TIMES
* A REPETER PLUSIEURS FOIS
* CEMENT TOGETHER
* A COLLER
* ALTERNATIVE ASSEMBLY
* ENSEMBLAGE ALTERNATIVE
* REMOVE AND THROW AWAY
* A RETIRER ET JETER
* DO NOT CEMENT
* NE PAS COLLER
* OPTIONAL PARTS
* PIECES EN OPTION
* DECAL
* DECAL COMANIE
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Gris
Gris clair
Gris hélicoptére
Gris vert
Bleu embléme
Blanc satiné
Jaune mat
Aluminium
Argent
Acier
Rouge brillant
Vert brillant
Noir satiné
Blanc mat
Gris moyen
Gris foncé moyen
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
DECAL APPLICATION INSTRUCTIONS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
NOTE: Decals are compatible with
setting solutions or solvents.
READ THIS BEFORE YOU BEGIN LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente
peu concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son support
en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85552500200), part number, description, your return address and phone number.
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2008. All rights reserved.
The Grumman F-14 Tomcat was a
supersonic, twin-engine, two seat, vari-
able geometry wing aircraft. The F-14
was used as a precision strike bomber,
defence interceptor and tactical recon-
naissance platform from 1974 to 2006.
Your Revell kit has optional AIM-54
Phoenix missles, AIM-9 Sidewinders,
AIM-7 Sparrow III's, 2000 lb JDAM
bombs, 500 lb. LGB bombs and 500
lb. MK-82 bombs, seated pilot or
standing figures of pilot and radar
officer plus two long range fuel tanks.
Optional decal markings are
included for F-14B Tomcat, BUNO
163227, VF-11 Red Rippers or
F-14B Upgrade Tomcat, BUNO
161860, VF-32 Swordsman.
Kit 5525 - Page 2
COCKPIT ASSEMBLY
1
122
FRONT
INSTRUMENT
PANEL
SEMI GLOSS
BLACK
11
COCKPIT
SEMI GLOSS
BLACK
GRAY
GRAY
GRAY
GREEN
GREEN
123
REAR
INSTRUMENT PANEL
SEMI GLOSS BLACK
19
REAR
CONTROL STICK
SEMI GLOSS
BLACK
15
RIGHT
SEAT SIDE
GRAY
16LEFT
SEAT SIDE
GRAY
65
PILOT
66
PILOT ARM
14
SEAT
DARK GRAY
17
EJECTION
SEAT
HANDLE
18
FRONT
CONTROL STICK
SEMI GLOSS
BLACK
COLOR NOTE:
WHITE: HELMETS
OLIVE GREEN: SUIT, LIFE VEST,
AND PARACHUTE STRAPS
SILVER: BUCKLES ON STRAPS
DARK GRAY: MASK AND HOSE
BLACK: BOOTS
1
FUSELAGE
TOP
FUSELAGE SIDE / WING ASSEMBLY
2
Kit 5525 - Page 3
21
LEFT
FUSELAGE SIDE
HOLES FOR
FUEL TANKS
HOLES FOR
FUEL TANKS
DECAL
44L
DECAL
44R
20
RIGHT
FUSELAGE SIDE
2
FUSELAGE BOTTOM
23
COMPRESSOR BLADES
STEEL
JET INTAKE
DANGER
VIEW WITH WINGS IN PLACE
F U S E L A G E
TOGETHER
2
FUSELAGE
BOTTOM
ALUMINUM
ALUMINUM
7
RIGHT
WING TOP
8
LEFT
WING TOP
10
LEFT
WING BOTTOM
9
RIGHT
WING BOTTOM
NOTE:
IF YOU DECIDE TO USE THE
PART #26 LADDER IN STEP (18)
THEN CAREFULLY CUT OUT THE
SHADED SECTION IN THIS STEP.
GEAR DOOR / POD ASSEMBLY
3
GUN PANEL / EXHAUST ASSEMBLY
4
Kit 5525 - Page 4
126
LEFT
NOSE GEAR
DOOR BLISTER
127
LEFT
NOSE GEAR
DOOR BOX
STEEL
28
LEFT
NOSE GEAR WELL
SEMI GLOSS WHITE
22
RADOME
25
GUN PANEL
71
ANGLE OF
ATTACK PROBE
27
RIGHT
NOSE GEAR WELL
SEMI GLOSS WHITE
125
RIGHT
HALF CHIN POD
LIGHT GRAY
124
LEFT
HALF CHIN POD
LIGHT GRAY
103
AFTERBURNER
STEEL
101
EXHAUST
NOZZLE
STEEL
102
EXHAUST NOZZLE
WITH SLOT
STEEL
3
ARRESTING HOOK
SEMI GLOSS WHITE
STEEL
ALUMINUM
34
NOSE GEAR
ACTUATOR
SEMI GLOSS WHITE
ALUMINUM
TCS with ALQ - 100 ANTENNA
“D”
“B”
Kit 5525 - Page 5
TAIL ASSEMBLY
5
LEFT MAIN WHEEL ASSEMBLY
6
4
RIGHT
VERTICAL TAIL
5
LEFT
VERTICAL TAIL
6
VERTICAL TAIL
FAIRING
6
VERTICAL TAIL
FAIRING
DARK GRAY
DARK GRAY
REAR VIEW OF FINS
SEMI GLOSS WHITE
120
MAIN WHEEL
FRONT
FLAT BLACK
52
LEFT
MAIN GEAR STRUT
INNER HALF
SEMI GLOSS WHITE
63
LEFT
MAIN GEAR STRUT
OUTER HALF
SEMI GLOSS WHITE
121
MAIN WHEEL
BACK
FLAT BLACK
SILVER
RIGHT MAIN WHEEL ASSEMBLY
7
LEFT WHEEL ASSEMBLY CONTINUED
6
Kit 5525 - Page 6
53
MAIN GEAR
RETRACTION
STRUT
SEMI GLOSS
WHITE
57
LEFT
MAIN GEAR
INNER DOOR
61
LEFT
MAIN GEAR
DOOR
59
LEFT
MAIN GEAR
OUTER DOOR
129
SMALL ECM
BLISTER
128
LARGE ECM
BLISTER
SEMI GLOSS WHITE
SEMI GLOSS
WHITE
SILVER
120
MAIN WHEEL
FRONT
FLAT BLACK
51
RIGHT
MAIN GEAR STRUT
INNER HALF
SEMI GLOSS WHITE
62
RIGHT
MAIN GEAR STRUT
OUTER HALF
SEMI GLOSS WHITE
121
MAIN WHEEL
BACK
FLAT BLACK
NOSE whEEl ASSEMBlY
8
RIGhT whEEl ASSEMBlY CONTINUED
7
Kit 5525 - Page 7
SEMI GLOSS WHITE
SEMI GLOSS
WHITE
60
RIGHT
MAIN GEAR
DOOR
56
RIGHT
MAIN GEAR
INNER DOOR
129
SMALL ECM
BLISTER
36
NOSE WHEELS
FLAT BLACK
69
NOSE GEAR
LIGHT
CLEAR
31
RIGHT
NOSE GEAR
LINK
SEMI GLOSS-
WHITE
32
LEFT
NOSE GEAR
LINK
SEMI GLOSS
WHITE
33
NOSE GEAR STRUT
SEMI GLOSS WHITE
(SHADED PART ALUMINUM)
128
LARGE ECM
BLISTER
58
RIGHT
MAIN GEAR
OUTER DOOR
53
MAIN GEAR
RETRACTION
STRUT
SEMI GLOSS
WHITE
30
BRAKE
CYLINDER
SEMI GLOSS
WHITE
Kit 5525 - Page 8
BOMB ASSEMBLY
9
MISSILE ASSEMBLY
10
147
LEFT
AN/ALQ-167
LANTRIN POD
148
RIGHT
AN/ALQ-167
LANTRIN POD
152
TOP
GBU-31 (V2/B) JDAM
2000 LB. BOMB
153
BOTTOM
GBU-31 (V2/B) JDAM
2000 LB. BOMB
144
TOP
MK-82
500-POUND BOMB
MED DARK GRAY
145
BOTTOM
MK-82
500-POUND
BOMB
MED DARK
GRAY
149
TOP
GBU-12 LASER GUIDED
500LB. BOMB
MED DARK GRAY
150
BOTTOM
GBU-12 LASER GUIDED
500LB. BOMB
MED DARK GRAY
151
BOMB FIN
OLIVE GREEN
151
BOMB FIN
OLIVE GREEN
48
AIM 9M
SIDEWINDER
LIGHT GRAY
49
MISSILE FIN
49
MISSILE FIN
STEEL
STEEL
STEEL
140
AIM 9M
SIDEWINDER
LIGHT GRAY
141
MISSILE FIN
141
FIN
MISSILE
STEEL
STEEL
STEEL
YELLOW
BROWN
SEMI GLOSS
WHITE
SEMI GLOSS
WHITE
73
BOTTOM
AIM-54C
PHOENIX MISSILE
LIGHT GRAY
43
TOP
AIM-54C
PHOENIX MISSILE
LIGHT GRAY
YELLOW
YELLOW
BROWN
OLIVE
GREEN
OLIVE
GREEN
Kit 5525 - Page 9
version 1 armament
12
146
AIM-7M
SPARROW MISSILES
PYLon / FUeL tanK assembLY
11
131
BOTTOM
FUEL TANK
130
TOP
FUEL TANK
136
RIGHT
WEAPONS
PYLON
138
RIGHT
WEAPONS
PYLON
135
LEFT
WEAPONS
PYLON
137
LEFT
WEAPONS
PYLON
158
LEFT
PHOENIX
PYLON
159
RIGHT
PHOENIX
PYLON
Kit 5525 - Page 10
142
BRU-32 WITH
ADU-703 BOMB
PYLONS
142
BRU-32 WITH
ADU-703 BOMB
PYLONS
version 2 armament
13
45
LEFT
WEAPONS RAIL
44
RIGHT
WEAPONS RAIL
PHOENIX
PYLON
AIM-54C
PHOENIX MISSILE
132
LEFT
FUEL TANK
RACK
133
RIGHT
FUEL TANK
RACK
LASER GUIDED
BOMBS
LASER GUIDED
BOMBS
LEFT
WEAPONS
PYLON
RIGHT
WEAPONS
PYLON
LANTIRN POD
WITH ADAPTER
FUEL TANK
FUEL TANK
Kit 5525 - Page 11
142
BRU-32 WITH
ADU-703 BOMB
PYLON
142
BRU-32 WITH
ADU-703 BOMB
PYLON
version 3 armament
14
FUEL TANK
132
FUEL TANK
RACK
133
FUEL
TANK RACK
FUEL TANK
44
RIGHT
WEAPONS RAIL
45
LEFT
WEAPONS RAIL
GBU-31 (V2/B) JDAM
2000 LB. BOMB
GBU-31 (V2/B) JDAM
2000 LB. BOMB
LEFT
WEAPONS
PYLON
LANTIRN POD
WITH ADAPTER
RIGHT
WEAPONS
PYLON
PHOENIX
PYLON
AIM-54C
PHOENIX MISSILE
Kit 5525 - Page 12
version 4 armament
15
50
SIDEWINDER
LAUNCH RAIL
50
SIDEWINDER
LAUNCH RAIL
134
SIDEWINDER LAUNCH
RAIL WITH CHAFF
DISPENSER
134
SIDEWINDER LAUNCH
RAIL WITH CHAFF
DISPENSER
139
RAIL ADAPTER
139
RAIL
ADAPTER
140
AIM 9M
SIDEWINDER
MISSILE
48
AIM 9M
SIDEWINDER
MISSILE
140
AIM 9M
SIDEWINDER
MISSILE
48
AIM 9M
SIDEWINDER
MISSILE
FUEL TANK
FUEL TANK
132
FUEL
TANK
RACK
133
FUEL
TANK
RACK
44
RIGHT
WEAPONS RAIL
45
LEFT
WEAPONS RAIL
142
BRU-32 WITH
ADU-703 BOMB
PYLONS
MK-82
500-POUND
BOMBS
MK-82
500-POUND
BOMBS
142
BRU-32 WITH
ADU-703 BOMB
PYLONS
LEFT
WEAPONS
PYLON
RIGHT
WEAPONS
PYLON
Kit 5525 - Page 13
CANOPY ASSEMBLY
16
0PEN
CLOSED
PAINT NOTE:
FRAME ON CANOPY AND
WINDSHIELD
MATCH TO AIRCRAFT
COLORS
24
CANOPY DECK
DARK GRAY
165
(HUD)
HEADS UP DISPLAY
CLEAR
68
CANOPY
67
WINDSCREEN
DARK GRAY
Kit 5525 - Page 14
FRONT assembly
17
laDDeR assembly
18
FIGURes assembly
19
26
LADDER
DARK GRAY
162
FIGURE
161
ARM
163
BACK
164
BACK
160
FIGURE
37
ANGLE OF
ATTACK PROBE
(AIC)
37
ANGLE OF
ATTACK PROBE
(AIC)
40
TOTAL
TEMPERATURE
PROBE
38
PITOT STATIC
PRESSURE PROBE
38
PITOT STATIC
PRESSURE PROBE
39
ANGLE OF ATTACK
SIDE PROBE
STARBOARD SIDE
PORT SIDE
FIGURE A
COMPLETED
FIGURE
COMPLETED
FIGURE
FIGURE B
COLOR NOTE:
WHITE: HELMETS
OLIVE GREEN: SUIT, LIFE VEST,
AND PARACHUTE STRAPS
SILVER: BUCKLES ON STRAPS
DARK GRAY: MASK AND HOSE
BLACK: BOOTS
Kit 5525 - Page 15
decal placement
20
decal placement
21
Kit 5525 - Page 16
/
