Sunx FX-501 Series User manual

Brand
Sunx
Model
FX-501 Series
Type
User manual
INSTRUCTION MANUAL
Photoelectric Sensor 'LJLWDO)LEHUVHQVRU$PSOL¿HU
);Ƒ
ME-FX501 No.0012-64V
Thank you very much for purchasing SUNX products. Please read this
Instruction Manual carefully and thoroughly for the correct and optimum
use of this product.
Kindly keep this manual in a convenient place for quick reference.
WARNING
Never use this product as a sensing device for personnel protection.
In case of using sensing devices for personnel protection, use products
which meet laws and standards, such as OSHA, ANSI or IEC etc., for
personnel protection applicable in each region or country.
Ɣ
Ɣ
1PART DESCRIPTION
<Description of the operation part>
UP key SET key DOWN key MODE key
Select setting items
•
&RQ¿UPWKHVHWWLQJ
contents
•
Select setting items
•Select Modes
Cancel during setting
•
•
2MOUNTING
How to connect
1. Fit the rear part of the mounting section of the
DPSOL¿HURQDPPZLGWK',1UDLO
2.
Press down the rear part of the mounting section
RIWKHXQLWRQWKHPPZLGWK',1UDLODQG¿WWKH
front part of the mounting section to the DIN rail.
How to remove
1. Push the controller forward.
2.
/LIWXSWKHIURQWSDUWRIWKHDPSOL¿HUWRUHPRYHLW
Note: 7DNHFDUHWKDWLIWKHIURQWSDUWLVOLIWHGZLWKRXWSXVKLQJWKHDPSOL¿HUIRUZDUGWKHKRRN
on the rear portion of the mounting section is likely to break.
+RZWRFRQQHFWWKH¿EHUFDEOH
%HVXUHWR¿WWKHDWWDFKPHQWWRWKH¿EHUV¿UVWEHIRUHLQVHUWLQJWKH¿EHUVWRWKH
DPSOL¿HU)RUGHWDLOVUHIHUWRWKH,QVWUXFWLRQ0DQXDOHQFORVHGZLWKWKH¿EHUV
6QDSWKH¿EHUORFNOHYHUGRZQWLOOLWVWRSVFRP-
pletely.
,QVHUWWKH¿EHUFDEOHVVORZO\LQWRWKHLQOHWVXQWLO
they stops. (Note 1)
5HWXUQWKH¿EHUORFNOHYHUWRWKHRULJLQDOSRVL-
tion till it stops.
1RWHV  ,QFDVHWKH¿EHUFDEOHVDUHQRWLQVHUWHGWRDSRVLWLRQZKHUHWKH\VKRXOGVWRSWKH
VHQVLQJUDQJHLVUHGXFHG6LQFHDÀH[LEOH¿EHULVHDVLO\EHQWWDNHFDUHZKHQLQ-
VHUWLQJWKH¿EHUV
 :LWKWKHFRD[LDOUHÀHFWLYHW\SH¿EHUVXFKDVFD-G4 or FD-FM2, insert the single
FRUH¿EHUFDEOHLQWRWKHEHDPHPLWWLQJLQOHW³3´DQGWKHPXOWLFRUH¿EHUFDEOHLQWR
the beam-receiving inlet.
If they are inserted in reverse, the sensing performance will deteriorate.
3WIRING
Make sure to connect or disconnect the quick-connection cable (optional)
in the power supply OFF condition.
How to connect
1. Hold the connector of the quick-connection
cable, and align its release lever with the
groove at the top portion of the controller
connector.
2. Insert the connector till a click is felt.
2
1
PPZLGWK',1UDLO
21
Fiber lock
lever
Fiber
1
2
Sensing output
operation indicator
(Orange)
DOWN key
MODE indicator: CUST (Yellow)
'LJLWDOGLVSOD\*UHHQ5HG UP key
SET key MODE key
02'(LQGLFDWRU352<HOORZ
MODE indicator: L / D (Yellow)
Quick-connection cable
&1Ƒ&Ƒ (Optional)
Groove
5HOHDVHOHYHU
How to remove
1. Press the release lever at the top of the
quick-connection cable connector, and pull
out the connector.
Note:
Take care that if the connector is pulled out without pressing the release lever, the re-
lease lever may break. Do not use a quick-connection cable whose release lever has
broken. Furthermore, do not pull by holding the cable, as this can cause a cable-break.
7HUPLQDODUUDQJHPHQW!
Terminal
No. Terminal name
1+V
2 Sensing output
0V
4INSTALL MORE AMPLIFIER OF SERIES CON-
NECTION TYPE
Make sure that the power supply is OFF while adding or removing the
series connection type.
Make sure to check the allowable ambient temperature since it depends
on the number of the series connection types connected in cascade.
In case 2 or more the series connection types are connected in cas-
cade, make sure to mount them on a DIN rail.
In case the amplifiers move on the DIN rail because of the attaching
FRQGLWLRQRUWKHDPSOL¿HUVDUHPRXQWHGFORVHWRHDFKRWKHULQFDVFDGH
fit them between the end plates MS-DIN-E (optional) mounted at the
two ends.
,QFDVHLQVWDOOLQJDGGLWLRQDODPSOL¿HURIVHULHVFRQQHFWLRQW\SHWKHPD[-
imum 11 the series connection types using sub cables can be added to
DQDPSOL¿HUXVLQJDPDLQFRQQHFWLRQFDEOH
When connecting 2 or more the series connection types in cascade, use
the sub cable (optional) for the second series connection type onwards.
When connected the series connection type are not close to each other
in parallel, be sure to mount the end plate MS-DIN-E (optional) at both
VLGHVRIHDFKDPSOL¿HU
)RURSWLFDOFRPPXQLFDWLRQUHIHUWR³ OPTICAL COMMUNICATION´
)RULQWHUIHUHQFHSUHYHQWLRQIXQFWLRQUHIHUWR³ INTERFERENCE
PREVENTION FUNCTION´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
)RUPRXQWLQJDQGUHPRYLQJWKHDPSOL¿HUUHIHUWR³ MOUNTING´
How to cascade
0RXQWWKHDPSOL¿HUVRQHE\RQHRQ
WKHPPZLGWK',1UDLO
6OLGHWKHDPSOL¿HUVQH[WWRHDFKRWK-
er, and connect the quick-connection
cables.
0RXQWWKHHQGSODWHVMS-DIN-E (op-
tional) at both the ends to hold the
DPSOL¿HUVEHWZHHQWKHLUÀDWVLGHV
4.
7LJKWHQ WKHVFUHZV WRIL[ WKHHQG
plates.
How to remove
1. Loosen the screws of the end plates.
5HPRYHWKHHQGSODWHV
6OLGHWKH DPSOLILHUVDQG UHPRYH
them one by one.
5I/O CIRCUIT DIAGRAM
<FX-501>
<FX-501P>
Notes: 1) The quick-connection sub cable does not incorporate +V (brown) and 0V (blue).
The power is supplied from the connector of the main cable.
 P$PD[LIRUPRUHVHULHVFRQQHFWLRQW\SHDUHFRQQHFWHGWRJHWKHU
 'RQRWXVHWKLVGHYLFHVDVDVHULHV$1'FRQQHFWLRQ
2
1
5HOHDVH
lever
Slide
Sub cable
(Optional)
Main cable
(Optional)
Communication
window
End plate
MS-DIN-E (Optional)
End plate
MS-DIN-E
(Optional) Slide
12 to 24V DC
±10%
Internal circuit Users’ circuit
Terminal No. Color code of quick-connection cable
Main circuit
(Brown) +V (Note 1)
(Black) Sensing output
(Blue) 0V (Note 1) P$PD[1RWH
Load +
-
12 to 24V DC
±10%
Internal circuit Users’ circuit
Color code of quick-connection cable
Main circuit
(Black) Sensing output
(Blue) 0V (Note 1)
P$PD[1RWH
Load
+
-
Terminal No.
(Brown) +V (Note 1)
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
6OPERATION PROCEDURE
The changed contents are not stored if turning the power OFF while set-
WLQJ7KHUHIRUHPDNHVXUHWRFRQ¿UPWKHVHWWLQJVE\SUHVVLQJWKH6(7NH\
before turning the power OFF.
:KHQWXUQLQJ21WKHSRZHU581 PRGHLV GLVSOD\HGDQG WKHGLJLWDO
display shows the threshold value (green) and the incident light intensity
(red).
When pressing MODE key, the mode changes as per the diagram below.
7TEACHING MODE
Be sure that detection may become unstable depending on the use en-
vironment in teaching if less margin is applied.
When teaching in Window comparator mode or Hysteresis mode, a set-
WLQJKDVWREHPDGHLQ352PRGHEHIRUHKDQG
In case one point teaching, make sure to set the shift amount. (initial
value is 10% or 100)
For setting, refer to <PRO 6>LQ³ PRO MODE´
1RUPDOO\³ ´RU³ ´EOLQNVDVDUHVXOWRIVWDELOLW\GHWHFWLRQ
Ɣ
Ɣ
Ɣ
7HDFKLQJFDQEHVHWLQ581PRGH
SRLQWWHDFKLQJ
/LPLWWHDFKLQJ
1RWH 7KHVKLIWYDOXHRIDSSR[LVDQLQLWLDOYDOXH7KHVKLIWYDOXHFDQEHFKDQJHWRGLV-
play in percent [Appro. 0~999% (unit 1 %)] or incident light intensity [0~9999 (Unit 1)].
For setting the shift amount, refer to 3526KLIWDPRXQWVHWWLQJ!LQ³ PRO
MODE´
)XOODXWRWHDFKLQJ
Ɣ
Ɣ
Ɣ
Displays threshold value (green) and incident light intensity (red).
7HDFKLQJ WKUHVKROGYDOXH¿QHDGMXVWPHQWDQGNH\ORFNIXQFWLRQ
can be set.
)RUVHWWLQJ PHWKRG RI HDFKIXQFWLRQUHIHUWR³ TEACHING
MODE´³ THRESHOLD VALUE FINE ADJUSTMENT FUNC-
TION´RU³ KEY LOCK FUNCTION´
•
•
•
581PRGH!
Select either Light-ON or Dark-ON.
)RUWKH VHWWLQJ UHIHU WR ³ SENSING OUTPUT OPERATION
MODE´
7KHGHIDXOWVHWWLQJLV³ ´/LJKW21
•
•
•
$QLWHPVHWLQ&86720PRGH5HVSRQVHWLPHVHWWLQJ(PLVVLRQ
power setting and Hysteresis setting) is displayed.
)RUGHWDLOVUHIHUWR³ CUSTOM MODE´
7KHGHIDXOWVHWWLQJLV³ ´UHVSRQVHWLPHVHWWLQJ
•
•
•
Advanced setting can be done.
)RUWKHVHWWLQJUHIHUWR³ PRO MODE´
•
•
&86720PRGH!
352PRGH!
6HQVLQJRXWSXWRSHUDWLRQPRGH!
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHRU+\VWHUHVLVPRGH
This is the method to set the shift amount to the desired value and to set
the threshold range by using the 1-point teaching.
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHRU+\VWHUHVLVPRGH
This is method to set the threshold range by conducting the 2-point teaching (P-1, P-2).
:KHQFRQGXFWLQJWHDFKLQJXVHVHQVLQJREMHFWV3DQG3ZKRVH
incident light intensities are different from each other.
SRLQWWHDFKLQJLQ:LQGRZFRPSDUDWRUPRGHRU+\VWHUHVLVPRGH
7KLVLVWKHPHWKRGWRFRQGXFWWKHSRLQWWHDFKLQJ333DQGWR
set the threshold range by setting the threshold value (1_SL) of the mid-
SRLQWEHWZHHQ³$´DQG³%´DQGWKHWKUHVKROGYDOXHB6/RIWKHPLGSRLQW
EHWZHHQ³%´DQG³&´
:KHQFRQGXFWLQJWHDFKLQJXVHVHQVLQJREMHFWV$%DQG&ZKRVHLQFL-
dent light intensities are different.
$IWHUWHDFKLQJ33DQG3ZLOOEHDXWRPDWLFDOO\UHORFDWHGLQDV-
FHQGLQJRUGHULHWKHORZHVWYDOXHLVSODFHGLQ³$´WKHVHFRQGORZHVWLQ
³%´DQGWKHKLJKHVWLQ³&´
6SDQDGMXVWPHQWLQ5LVLQJGLIIHUHQWLDOPRGHRU7UDLOLQJGLIIHUHQWLDOPRGH
7KHVSDQDGMXVWPHQWLQULVLQJGLIIHUHQWLDOPRGHRUWUDLOLQJGLIIHUHQWLDO
mode can be set by pressing down the UP key or DOWN key after
pressing down SET key. At this time, all Mode indicators blinks.
3UHVVWKH6(7NH\WRFRQ¿UPWKHVHWWLQJLWHP
7KHWKUHVKROGFDQEHVHWE\XVLQJWKH WKUHVKROGYDOXH ¿QHDGMXVWPHQW
IXQFWLRQ)RUWKHWKUHVKROGYDOXHILQHDGMXVWPHQWIXQFWLRQUHIHUWR
³THRESHOLD VALUE FINE ADJUSTMENT FUNCTION´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
 3UHVVWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
³´LVGLVSOD\HGLQWKHGLJLWDOGLVSOD\JUHHQDQGWKHDOO02'(LQGLFDWRUV
(yellow) brink.
 3UHVVWKH6(7NH\LQWKHVHQVLQJREMHFWDEVHQWFRQGLWLRQ
 $WKUHVKROGYDOXHLVVHWEHWZHHQWKHVWHSDQG
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
or
 ³
´
is displayed by pressing down UP key in the digital display (green) in
VWHSDQG³
´
is displayed by pressing down DOWN key in the digital
display (green) in step 2.
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
2. Press down UP key or DOWN key
3UHVVGRZQ83NH\7KHWKUHVKROGOHYHOLVVKLIWHGWRD YDOXH DSSUR[ 
higher (low sensitivity) than that set at step 1. (Note)
3UHVVGRZQ'2:1NH\ 7KHWKUHVKROGOHYHOLVVKLIWHGWRDYDOXHDSSUR[
lower (high sensitivity) than that set at step 1. (Note)
 3UHVVWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
³´LVGLVSOD\HGRQWKHGLJLWDOGLVSOD\JUHHQDQGWKHDOO02'(LQGLFDWRUV
(yellow) brink.
or
or
1.
%\SUHVVLQJGRZQ6(7NH\³
´LVGLVSOH\HGRQWKHGVLWDOGLVSOD\JUHHQ
and all MODE indicators (yellow) brink.
 7KHWKUHVKROGYDOXHB6/WKDWLVORZHUIURPWKHLQFLGHQWOLJKWLQWHQVLW\
and the threshold value (2_SL) that is 10% higher from the incident light in-
tensity are set. (Note 1, 2)
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Notes: 1) The shift amount of 10% is an initial value. The shift amount can
EHVHWLQ352PRGH)XUWKHUPRUHWKHVKLIWYDOXHFDQEHVHWLQ
incident light amount.For setting method, refer to <PRO 6> in
³PRO MODE´
 ,IWKHYDOXHDIWHUVHWWLQJH[FHHGVWKHPD[LPXPPLQLPXPWKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
or
 3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
<Window comparator mode>
Set to de-
sired value
Set to de-
sired value
1_SL P-1 2_SL
+\VWHUHVLVPRGH!
Set to de-
sired value
1_SL P-1 2_SL
Set to de-
sired value
 ³ ´LVGLVSOD\HGRQWKHGLJLWDOGLVSOD\JUHHQDQGZKHQWKHVHQVLQJRE-
MHFWSDVVHGWKURXJKUHOHDVHWKH6(7NH\
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
or
Automatic
 5XQWKHVHQVLQJREMHFWRQWKHOLQHDQGKROGGRZQWKH6(7NH\
1.
%\SUHVVLQJGRZQ6(7NH\³
´LVGLVSOH\HGRQWKHGHVLWDOGLVSOD\JUHHQ
and all MODE indicators (yellow) brink.
+\VWHUHVLVPRGH!
1_SL (P-1) 2_SL (P-2)
<Window comparator mode>
1_SL (P-1) 2_SL (P-2)
 3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
 7KHYDOXHRIWKH¿UVWSRLQWB6/DQGWKHVHFRQGSRLQWB6/DUHVHWJUHHQ
(Note)
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Note,IWKHYDOXHDIWHUVHWWLQJH[FHHGVWKHPD[LPXPPLQLPXPWKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
 ³ ´LVGLVSOD\HGLQGLJLWDOGLVSOD\JUHHQDQGDOO02'(LQGLFDWRUV\HOORZ
brink.
 ,QVHFRQGWLPHSUHVVLQJGRZQ6(7NH\LQVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
or
<Window comparator mode> +\VWHUHVLVPRGH!
 3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQ
 7KHWKUHVKROGB6/RIWKHPLGSRLQWEHWZHHQ³$´DQG³%´DQGWKHWKUHVKROG
B6/RIWKHPLGSRLQWEHWZHHQ³%´DQG³&´DUHVHW1RWH
 ,QFDVHVWDEOHVHQVLQJLVSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
,QFDVHVWDEOHVHQVLQJLVQRWSRVVLEOH³ ´EOLQNVLQWKHUHGGLJLWDOGLVSOD\
Note,IWKHYDOXHDIWHUVHWWLQJH[FHHGVWKHPD[LPXPPLQLPXPWKH
PD[LPXPPLQLPXPVHQVLWLYLW\ZLOOEHVHW
 ³ ´LVGLVSOD\HGLQWKHGLJLWDOGLVSOD\JUHHQ
 3UHVVGRZQ WKH 6(7NH\LQWKH VHQVLQJ REMHFW SUHVHQWFRQGLWLRQIRUWKH
second point.
 ³ ´EOLQNVLQWKHGLJLWDOGLVSOD\JUHHQ
 3UHVVGRZQWKH6(7NH\LQWKHVHQVLQJREMHFWSUHVHQWFRQGLWLRQIRUWKHWKLUG
point.
or
A 2_SL1_SL B CA 2_SL1_SL B C
Short span
(Changed intensity)
Press Long span
(Changed intensity)
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
8
THRESHOLD VALUE FINE ADJUSTMENT FUNCTION
6HWWKH¿QHDGMXVWPHQWRIWKUHVKROGYDOXHLQ581PRGH
Pressing down the UP key increases the threshold value, and pressing
down the DOWN key decreases the threshold value.
When setting sensing output to the window comparator mode or hystere-
VLVPRGH³ ´DQG³ ´FDQEHFKDQJHGWRDQRWKHUE\SUHVVLQJ
down SET key for 2 sec.
,QFDVHFRQGXFWLQJWKUHVKROGYDOXH¿QHDGMXVWPHQWRI³ ´RU³ ´
SUHVVGRZQ83NH\RU'RZQNH\DQG³ ´RU³ ´DUHGLVSOD\HG
7KHQWKHWKUHVKROGYDOXH¿QHDGMXVWPHQWFDQEHFRQGXFWHG
Set by pressing down the SET key or the value is automatically memorized
unless any key operation is carried out within a certain period of time.
For setting of the sensing output, refer to <PRO 6>LQ³ PRO MODE´
1RUPDOPRGH5LVLQJGLIIHUHQWLDOPRGHRU7UDLOLQJGLIIHUHQWLDOPRGH!
:LQGRZFRPSDUDWRUPRGHRU+\VWHUHVLVPRGH!
Note: It may not respond when values of ³ ´DQG³ ´DUHFORVHEHFDXVHRIUHOD-
WLRQRIK\VWHUHVLV%HVXUHWRFRQ¿UPZLWKWKLVGHYLFH
<Forced ON output mode or Forced OFF output mode>
9KEY LOCK FUNCTION
The key lock function prevents key operations so that the conditions set
in each setting mode are not inadvertently changed.
%\NHHSLQJWRSUHVVGRZQWKH6(7NH\DQGWKH02'(NH\IRUVHFRU
more, setting and releasing of key lock can be done.
,IRSHUDWLQJNH\VZLWFKDIWHUNH\ORFNLVVHW³ ´LVLQGLFDWHGRQ
the digital display.
6HWNH\ORFN!
5HOHDVHNH\ORFN!
10
SENSING OUTPUT OPERATION MODE
When MODE indicator: L / D (yellow) lights up, sensing output operation
can be set.
By pressing UP key or DOWN key, sensing output operation can be changed.
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
11
CUSTOM MODE
:KHQ02'(LQGLFDWRU&867\HOORZOLJKWVXS5HVSRQVHWLPHVHWWLQJ
Emission power setting or Hysteresis setting can be displayed.
Setting contents of the displayed item can be changed.
For the setting procedure, refer to 352&86720VHWWLQJ!LQ³ PRO MODE´
By pressing UP key or DOWN key, the setting in each item can be changed.
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
For setting of each item, refer to the following table.
Item Digital display 5HIHUHQFHLWHP
5HVSRQVH
time setting
3525HVSRQVHWLPHVHWWLQJ! in
³PRO MODE´
Emission
power setting
352(PLVVLRQSRZHUVHWWLQJ! in
³PRO MODE´
Hysteresis
setting
352+\VWHUHVLVVHWWLQJ! in
³PRO MODE´
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
12
PRO MODE
:KHQ02'(LQGLFDWRU352\HOORZOLJKWVXS352PRGHFDQEHVHW
3UHVV6(7NH\WRFRQ¿UPWKHVHWWLQJ
Ɣ
Ɣ
&RQ¿UPHG
Press
(Light-ON) (Dark-ON)
Press
581PRGH!
6HWWLQJRINH\ORFN!
Press down for
VHFRUPRUH
Automatic
581PRGH!
5HOHDVHRINH\ORFN!
Automatic
Press down for
VHFRUPRUH
,
are displayed
6KLIWDPRXQWVHWWLQJ!
Displayed in percentage
Changeable in the range of 0 to 999%
,QFLGHQWOLJKWLQWHQVLW\1RWH
Shift amount
setting
(15%)
:&RQ¿UPHG :Selected
352PRGH! 352!
ȝVRUOHVV
5HVSRQVHWLPHVHWWLQJ!1RWH
ȝVRUOHVV
24ms or less
2ms or less
ȝVRUOHVV
4ms or less
ȝVRUOHVV
+\VWHUHVLVVHWWLQJ!
Small Large
Standard
(Standard)
Hysteresis
setting
(No timer)
7LPHURSHUDWLRQ!
No timer
OFF-delay timer
When timer
is valid
ON-delay timer
ON / OFF-delay timer
One-shot timer
ON-delay / One-shot timer
5HVSRQVH
time setting
Timer
setting
Emission
power setting
7LPHUSHULRG!1RWH
Time period depends on timer range
:KHQXVLQJWKHWLPHUUDQJH³
ms
´VHWWLQJ
³ ´DSSUR[PV³ ´WR³ ´DSSUR[WRPV
:KHQXVLQJWKHWLPHUUDQJH³
sec.
´VHWWLQJ
³ ´DSSUR[VHF³ ´WR³ ´DSSUR[WRVHF
:KHQXVLQJWKHWLPHUUDQJH³
1/10ms
´VHWWLQJ
³ ´DSSUR[PV³ ´WR³ ´DSSUR[WRPV
(5ms)
OFF-delay
timer
When timer is valid
(Following is for OFF-delay timer selected)
7LPHUUDQJHVHWWLQJ!
ms 1/10ms
sec.
(ms)
Timer range
setting
(100%)
Middle emis-
sion power
Incident light
intensity
(SET)
:KHQVHOHFWLQJVDWXUDWLRQFRUUHFWLRQ!
(Correcting)
(*1)
581PRGH!
(*1): In case saturation correction is NG, it is
not displayed.
Saturation
correction
Automatic
Automatic
(PLVVLRQSRZHUVHWWLQJ!1RWH
Saturation correction
Middle emission power
Changeable in the range of 25 to 100%
Low emission power
Changeable in the range of 25 to 100%
High emission power
Changeable in the range of 25 to 100%
6HWWLQJRIGLJLWDOGLVSOD\WXUQLQJ!
Turning OFF
Turning ON
352! (Lock OFF)
Teaching
lock setting
7HDFKLQJORFNVHWWLQJ!
Lock OFF
Lock ON
6HWWLQJLWHPVLQGLJLWDOGLVSOD\VHWWLQJ!
Incident light intensity
Displayed in percentage
Peak / bottom value
Digital display
item setting
Incident light
intensity
(Turning OFF)
Digital display
turning on setting
7LPHSHULRGKROGVHWWLQJ!1RWH
Hold OFF
Hold ON
(&2VHWWLQJ!
(ECO OFF)
(&2VHWWLQJ!
ECO OFF
Full
ECO ON
Time period
hold setting
(Hold OFF)
352
Press
&RQ¿UPHG
(Threshold value)
Automatic
or
Press
&RQ¿UPHG
(Threshold value)
Press or Press
Automatic
or
Press
or Press Press
(Threshold value)
or
&RQ¿UPHG
Automatic
Automatic
or
Press
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Notes: 1) ,Q FDVHUHVSRQVH WLPHVHWWLQJ³ ´ LV VHW WR ³ ´³ ´RU³ ´
WKHGLVSOD\IRULQFLGHQWOLJKWLQWHQVLW\FDQVKRZVWKHGLJLWRI PD[  ,Q FDVH
³ ´LVVHOHFWHG,WZLOOGLVSOD\WKHGLJLWRIPD[$QG,QFDVH³ ´RU
³ ´LVVHOHFWHGLWZLOOGLVSOD\WKHGLJLWRIPD[
2)
Set timer period after setting timer range since timer period depends on the timer range.
 
,QFDVHWKHUHVSRQVHWLPHVHWWLQJ³ ´LVVHWWR³ ´³ ´RU³ ´
WKHPD[LPXPOLJKWLQWHQVLW\FDQEHVHWWR$QGWKHUHVSRQVHWLPHLVVHWWR³
´WKHPD[LPXPOLJKWLQWHQVLW\FDQEHVHWWR$QGWKHUHVSRQVHWLPHLV
VHWWR³ ´RU³ ´WKHPD[LPXPOLJKWLQWHQVLW\FDQEHVHWWR
4)
,QFDVHWKHUHVSRQVHWLPHVHWWLQJ³ ´LVVHWWR³ ´ZKHQWKHK\VWHUHVLV
VHWWLQJ³ ´LV³ ´ WKHHPLWWLQJ SRZHU EHFRPHVORZ VHQVLELOLW\ ³ ´
ZKLFKHYHUVHOHFWLQJ³ ´³ ´RU³ ´
5) In order to clear the value, set the time period holding function to OFF once. Turn-
ing the power OFF can also clear the value.
6)
,QFDVHWKHUHVSRQVHWLPHVHWWLQJ³ ´LVVHWWR³ ´³ ´RU³ ´WDUJHW
VHWWLQJRIWKHGLVSOD\DGMXVWPHQWVHWWLQJEDQEHVHWIURPWR$QGVHWWLQJWR
³ ´WKHGLVSOD\DGMXVWPHQWVHWWLQJEDQEHVHWIURPWR$QGVHWWLQJWR³
´RU³ ´WKHGLVSOD\DGMXVWPHQWVHWWLQJFDQEHVHWIURPWR
7) In case using in differential mode, set threshold value 20 or more
when the hyster-
HVLVVHWWLQJ³ ´LV³ ´DQG
VHWWKUHVKROGYDOXHRUPRUH
when the hyster-
HVLVVHWWLQJ³ ´LV³ ´RU³ ´
.
Item Default
setting Description
5HVSRQVHWLPHVHWWLQJ
Set response time.
Timer setting Set operation and period of the timer.
Hysteresis
setting
Hysteresis can be set when the normal mode or the
window comparator mode is selected.
:KHQVHWWLQJWR³ ´LWEHFRPHVORZVHQVLELOLW\
Shift amount
setting Set shift amount of threshold value in limit teaching.
Emission power
setting
Set emission power.
³ ´6DWXUDWLRQFRUUHFWLRQ
³ ´+LJKHPLVVLRQSRZHUWR
³ ´0LGGOHHPLVVLRQSRZHUWR
³ ´/RZHPLVVLRQSRZHUWR
Timer range setting
Change unit time of timer.
Teaching lock
setting
Be able to prevent from wrong operation of teaching.
³ ´ Teaching mode is valid
³ ´ Teaching mode is invalid
Digital display
item setting
Incident light intensity can be displayed in percentage or the
peak / bottom value can be displayed on the digital display (red).
Digital display
turning on setting
Sets the viewing orientation of the digital display.
ECO setting
Power consumption can be lowered.
³ ´(&22))
³ ´
If any key operation is not carried out for 20 sec.
LQ581PRGHWKHGLJLWDOGLVSOD\WXUQV2))
³ ´
If key operation is not done in 20 sec. or setting the key
lock function, digital display turns OFF. Furthermore, if
key lock function is set to ON, all indicator turns OFF.
352!
6HWWLQJRIWKUHVKROGYDOXHWUDFNLQJ!
Threshold tracking is OFF
Select threshold tracking cycle in the
range of 1 to 9,999 sec.
Tracks threshold when the sensing out-
put is OFF
Tracks threshold when the sensing
output is ON
1RWVWRUHGLQ((3520
Select the cycle of storage in EE-
3520LQWKHUDQJHRIWRWLPHV
Limit teaching
Auto teaching
352!
6HQVLQJRXWSXWVHWWLQJ!
Normal mode
Window comparator mode
5LVLQJGLIIHUHQWLDOPRGH1RWH
Trailing differential mode (Note 7)
Hysteresis mode
Forced ON output mode
Forced OFF output mode
Sensing
output setting
Window comparator mode or Hysteresis mode (The following dia-
gram is used when selecting Window comparator mode.)
6KLIWDPRXQWVHWWLQJ!
Shift amount setting
(Displayed in percentage)
Sensing
output setting
Storage
cycle setting
(OFF)
(OFF)
Algorithm
setting
Limit
teaching
352
Logical
operation
setting
Threshold
tracking setting
Threshold track-
ing cycle setting
(OFF)
/RJLFDORSHUDWLRQVHWWLQJ!
Invalid or
and [RU
(Invalid)
Between
DGMDFHQW
DPSOL¿HUV
Back up
ON
%DFNXSVHWWLQJ!
Back up ON
Back up OFF
Back up
setting
Data bank
saving setting
&RS\ORFNVHWWLQJ!
Copy lock OFF
Copy lock ON
Copy lock
setting
352! (YES)
(2 turns)(Blink)
(good)
Copy
setting
&RS\DFWLRQVHWWLQJ!
'LVSOD\DGMXVWPHQW
Display copy
'LVSOD\DGMXVWPHQW2))
'DWDEDQNVDYLQJVHWWLQJ!
1 ch 4 ch 7 ch
2 ch 5 ch FK
FK 6 ch
(1 ch)
%OLQNVWLPHV
(good)(YES)
(Blink)
Automatic
Automatic
352!
'DWDEDQNORDGLQJVHWWLQJ!
1 ch 4 ch 7 ch
2 ch 5 ch FK
FK 6 ch
(1 ch)
%OLQNVWLPHV
(good)(YES)
(Blink)
Data bank
loading setting
Automatic
Automatic
Copy action
setting
Display
DGMXVWPHQW
OFF
Copy lock
OFF
&RPPXQLFDWLRQSURWRFROVHWWLQJ!
Communication mode
Communication emission
halt
Communica-
tion protocol
setting
Communica-
tion mode
352!
(Default)
Interference
prevention
setting
,QWHUIHUHQFHSUHYHQWLRQ VHWWLQJ!
Default
Different frequency setting
'LIIHUHQWIUHTXHQF\VHWWLQJ!
Emission frequency 1
Emission frequency 2
(PLVVLRQIUHTXHQF\
:KHQVHOHFWLQJGLIIHUHQWIUHTXHQF\VHWWLQJ!
Different fre-
quency setting
Emission
frequency 1
CUSTOM
setting
&86720VHWWLQJ!
5HVSRQVHWLPHVHWWLQJ
Emission power setting
Hysteresis setting
5HVSRQVH
time setting
%OLQNVWLPHV
(Blink)
581PRGH!
5HVHW
setting
Automatic
352!
5HIHUWR³&RGHVHWWLQJWDEOH´
&RQGXFW&RQ¿UPHG
: Select code
Code
setting
(OFF) 'LVSOD\DGMXVWPHQWVHWWLQJ!
OFF
&RQ¿UP
Target setting (Note 6)
'LVSOD\DGMXVW-
ment setting
:KHQVHOHFWLQJWDUJHWVHWWLQJ!
(0)
&RQ¿UPHG
Target
setting
'LVSOD\DGMXVW-
ment setting
352!
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
Item Default
setting Description
Logical
operation
setting
Set a logical operation method between sensing output (in
FDVHRXWSXWVVHQVLQJRXWSXWRIWKLVGHYLFHDQGDQDGMD-
FHQWDQGXSSHUDPSOL¿HUIURPDQGRU[RU
Sensing output of
DQDGMDFHQWDQG
XSSHUDPSOL¿HU
Sensing
output of this
device
Setting of logical operations
and or [RU
ON ON ON ON OFF
ON OFF OFF ON ON
OFF ON OFF ON ON
OFF OFF OFF OFF OFF
Setting of
threshold value
tracking
This mode can change the threshold value in each
cycle (1 to 9,999 sec.) that is set with the variations of
the incident light intensity. The tracking shift amount is
the one which was set at the shift setting.
Sensing
output setting
Selects either a tracking threshold when the sensing
output is OFF or a tracking threshold when the sens-
ing output is ON.
Storage cycle
setting
6HOHFWVDWKUHVKROGVWRUDJHF\FOHLQ((3520IURP
to 250 times.
Algorithm
setting
1RWH
When setting to limit teaching, threshold value be fol-
lowed up on the bases of shift amount. Furthermore,
when setting to auto teaching, threshold value be fol-
lowed up on the bases of each cycle
1RWHV  :KHQVHWWLQJ³ ´FRQGXFWVWKHOLPLW WHDFKLQJ WRZDUG WKH FKDQJHG LQFLGHQW
light intensity.
Shift direction of the threshold differs depending on the combination of the sensing
output status and the sensing output operation.
Sensing output status Sensing output operation Shift direction
Sensing output ON Light-ON
-
Sensing output ON Dark-ON +
Sensing output OFF Light-ON +
Sensing output OFF Dark-ON
-
&RGHVHWWLQJWDEOH
*UHHQGLJLWDOGLVSOD\ULJKWVLGHLVWKH¿UVWGLJLW
Code
Forth digit
Code
Third digit
Code
Second digit
Code
First digit
Sensing output
operation mode Timer operation Timer period CUSTOM setting
Light-ON No timer 0.5ms 5HVSRQVHWLPH
setting
Dark-ON OFD 1ms Emission power
setting
OND PV
Hysteresis setting
ONOF 5ms
OSD 10ms
ONOS PV
 
50ms
 
100ms
 
PV
 
500ms
 
1 sec.
 
2 sec.
 
VHF
 
4 sec.
 
5 sec.
OFD: OFF-delay timer, OND: ON-delay timer
ONOF: ON / OFF-delay timer, OSD: One-shot timer
ONOS: ON-delay / One-shot timer
5HGGLJLWDOGLVSOD\ULJKWVLGHLVWKH¿UVWGLJLW
Code
Forth digit
Code
Third digit
Code
Second
digit
Code
First digit
Copy lock
setting
Hysteresis
setting
Setting items
in digital dis-
play setting
Back up
setting
5HVSRQVH
time setting
Sensing out-
put setting
Copy lock
OFF H-02 Incident light
intensity
Back up ON
H-SP
Normal mode
Copy lock
ON H-02 Incident light
intensity
Back up OFF
FAST WC mode
Copy lock
OFF + Displayed in
percentage
Back up ON
STD
5LVLQJGLIIHU-
ential mode
Copy lock
ON + Displayed in
percentage
Back up OFF
LONG
Trailing differ-
ential mode
Copy lock
OFF H-01 Peak / bot-
tom value
Back up ON
U-LG HYS mode
Copy lock
ON H-01 Peak / bot-
tom value
Back up OFF
+<3(5
(WC mode: Window comparator mode, HYS mode: Hysteresis mode)
Ɣ
Ɣ
Item Default
setting Description
Time period
hold setting
³ ´3HDN  ERWWRP YDOXHLQ WKHGLJLWDOGLVSOD\
refreshing condition can be displayed.
³ ´3HDN ERWWRPYDOXHLQWKHKROG FRQGLWLRQ
can be displayed.
Data bank loading
setting
/RDGDVHWWLQJIURPVSHFL¿HGGDWDEDQN
Data bank saving
setting
6DYHDVHWWLQJWRVSHFL¿HGGDWDEDQN
Back up
setting
Select to save or not to save the threshold value by
WHDFKLQJLQ((3520
Copy setting
-
Using optical communications, be able to copy setting
FRQWHQWVLQPDLQDPSOL¿HUWR DOORIWKHVXEDPSOL¿HUV
FRQQHFWHGIURPWKHPDLQDPSOL¿HU
This product can send and receive threshold value.
)RUWKHRSWLFDOFRPPXQLFDWLRQVUHIHU WR³ OPTI-
CAL COMMUNICATIONS´
Copy action
setting
&RS\RILWHPVLQ GLVSOD\DGMXVWPHQWVHWWLQJDQGLQFL-
dent light intensity are conducted or canceled by us-
ing optical communication.
In case the incident light intensity does not have
enough margin, automatically set optimum value.
)RUWKHRSWLFDOFRPPXQLFDWLRQV UHIHUWR³ OPTICAL
COMMUNICATIONS´
³ ´ 'LVSOD\ DGMXVWPHQWRIPDLQDPSOLILHUDQG
VXEDPSOL¿HUVFDQEHFRQGXFWHG
 6HWWRWKHWDUJHW YDOXHRIGLVSOD\DGMXVW-
PHQWLQHDFKDPSOL¿HU
³ ´ ,QFLGHQWOLJKWLQWHQVLW\RIPDLQDPSOL¿UHFDQ
EHFRSLHGWRVXEDPSOL¿HU+RZHYHUZKHQ
WKHGLIIHUHQFHEHWZHHQPDLQDPSOL¿HUDQG
VXEDPSOL¿HULVELJLWZLOOQRWEHFRSLHG
³ ´ 'LVSOD\DGMXVWPHQWRIVXE DPSOLILHUFDQ
EHVHWWR2))'LVSOD\DGMXVWPHQWRIPDLQ
DPSOL¿HULVQRWVHWWR2))
Do not press down the SET key many
WLPHVLQGLVSOD\RI³ ´:KHQ³
´LVGLVSOD\HGLQ FRQ¿UPDWLRQDOVRGRQRW
press down SET key many times.
Copy lock
setting
When setting data loading / saving bank setting by
optical communication, this function can set that the
VXEDPSOL¿HUZKLFKLVVHWFRS\ORFN21³
´DQGWKHORZHUVXE DPSOLILHUGRQRWUHFHLYHWKH
VHWWLQJFRQWHQWV+RZHYHUHYHQLIFRS\ ORFN21³
´LVVHWWKHFRS\DFWLRQVHWWLQJLVFRPPX-
nicated.
Communication
protocol setting
When conducting the copy setting or setting of data
bank loading / saving from the main amplifier via
optical communications, the optical communications
WKURXJKDVXEDPSOL¿HUZKLFKLVVHWWRFRPPXQLFDWLRQ
KDOW³ ´DQG WKH IROORZLQJVXEDPSOLILHUV
can be halted.
Code setting
&RQVLVWHQWVHWWLQJFDQEH GRQHE\LQSXWWLQJGLJLW
code instead of independent setting.
,QDGGLWLRQSUHVHQWVHWWLQJFDQEHFRQ¿UPHG
'LVSOD\DGMXVW-
ment setting
The incident light intensity can be set to target value.
,IWKHGLVSOD\DGMXVWPHQW VHWWLQJLVFRQGXFWHGZKHQ
LQFLGHQWOLJKWLQWHQVLW\GRHVQRWKDYHHQRXJKPDUJLQ³
´EULQNV
³ ´ 'LVSOD\DGMXVWPHQW2))
³ ´ 6OLGHWRVPDOOHUVLGH LQFLGHQWOLJKWLQWHQ-
sity from the set of target setting.
³ ´
Set incident light intensity to value you want.
,QFDVHVHWWLQJWRDGMXVWPHQWVHWWR
5HVHWVHWWLQJ
-
,IVHWWLQJWR³ ´UHWXUQWRGHIDXOWVHWWLQJVIDFWRU\
settings)
.
CUSTOM setting
Select an item in CUSTOM mode to display.
Interference pre-
vention setting
Number of adherence mounting of sensor head de-
pends on response time of interference prevention
function.
)RUGHWDLOUHIHU³ INTERFERENCE PREVENTION
FUNCTION.´
³ ´㧦Set when using the interference prevention
IXQFWLRQE\RSWLFDOFRPPXQLFDWLRQ 0D[L-
mum adherence mounting of sensor head
is 12 units
³ ´㧦Set when using interference prevention
function by changing emitting frequency.
7KHPD[LPXPDGKHUHQFHPRXQWLQJby
VHWWLQJW\SHVRI HPLVVLRQ IUHTXHQF\LV
units.
Sensing output
setting
Set sensing output.
³ ´1RUPDOPRGH
Sets a threshold value for ON / OFF operation.
³ ´:LQGRZFRPSDUDWRUPRGH
6HWVWZRWKUHVKROGYDOXHV DQGMXGJHVHLWKHUZLWKLQ
the required range or not. This can be selected in 1
SRLQWWHDFKLQJ
³ ´5LVLQJGLIIHUHQWLDOPRGH
Only when drastic rises in incident light intensity are
detected.
³ ´7UDLOLQJGLIIHUHQWLDOPRGH
Only when drastic drops in incident light intensity are
detected.
³ ´+\VWHUHVLVPRGH
Changes hysteresis to ignore small change of inci-
dent light intensity.
7KLVFDQEHVHOHFWHGLQSRLQWWHDFKLQJ
Sets a threshold value for ON / OFF operation.
³ ´)RUFHG21RXWSXWPRGH
Sets forcibly the output to ON.
³ ´)RUFHG2))RXWSXWPRGH
•
•
•
•
•
•
•
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
13
ERROR INDICATION
In case of errors, attempt the following measures.
Error
indication
Description 5HPHG\
((3520LVEURNHQRU UHDFKHG
the end of its working life. 3OHDVHFRQWDFWRXURI¿FH
((3520ZULWLQJHUURU
Load of the sensing output is
short-circuited causing an over-
FXUUHQWWRÀRZ
Turn OFF the power and check the
load.
Communication error when the
amplifiers are mounted in cas-
cade.
Verify that there is no loose or clear-
DQFHEHWZHHQDPSOL¿HUV
Communication error between the
upper communication unit and
DPSOL¿HUV
Verify that there is no loose or clear-
ance between the upper communication
XQLWDQGDPSOL¿HUV
14
OPTICAL COMMUNICATION
When the setting of data bank loading / saving, copy setting or copy ac-
tion setting is conducted via optical communications, add the sub ampli-
¿HUVWRULJKWVLGHRIWKHPDLQDPSOL¿HUDVIROORZV
,IDQDPSOL¿HULVXQGHUDQ\RIWKHIROORZLQJFRQGLWLRQVWKHVHWWLQJRIGDWD
bank loading / saving or copy setting cannot be carried out .
&RS\ORFNVHWWLQJLVVHWWRFRS\ORFN21³ ´
Digital display is blinking
When communication protocol of a sub amplifier is set to communication
emission
KDOW³ ´WKHVHWWLQJRIGDWDEDQNORDGLQJVDYLQJ
or
copy setting
FDQQRWEHFDUULHGRXWWRVXEDPSOL¿HUVVXEVHTXHQWWRWKHPHQ-
WLRQHGDPSOL¿HU
Make sure to mount closely like follows since interference prevention
function is conducted by optical communication.
:KHQWKLVGHYLFHDQGRWKHUGHYLFHHJ¿EHUVHQVRUDPSOL¿HUVSUHVVXUH
sensor controller, etc.) are connected together in cascade, install those
products so that they are in order of Group A, B, C and D as shown be-
low. This device is included in Group D.
$VIRUWKHSURGXFWVWKDWDUHORFDWHGEHWZHHQGLIIHUHQWJURXSVDI¿[WKH
DPSOL¿HUSURWHFWLRQVHDOFX-MB1 (optional) on the communication win-
dow of each corresponding product.
Set same model of devices in same group.
,QFDVHSXWWLQJLQWKLVGHYLFHDQGRWKHUW\SHRIGHYLFHVHJ¿EHUVHQVRU
DPSOL¿HUVSUHVVXUHVHQVRUFRQWUROOHUHWFDVPL[HGLQVWDOODWLRQLWHPV
that can copy are limited.
7KHLWHPVWKDWFDQFRS\LQPL[HGLQVWDOODWLRQDUHGLJLWDOGLVSOD\VHWWLQJLQ
581PRGH(&2VHWWLQJSHULRGKROGVHWWLQJDQG&86720VHWWLQJ
In case conducting copy setting of this device and other FX-500 series
together, functions which are incorporated in this device will be copied
but functions which are not incorporated in this device will not be copied.
Ɣ
Ɣ
Ɣ
•
•
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
6XEDPSOL¿HUV
0DLQDPSOL¿HU
Communication direction
15
INTERFERENCE PREVENTION FUNCTION
This device incorporates an interference prevention function by setting
different emitting frequencies different from an interference prevention
function by optical communication.
For the setting, refer to < PRO5: Interference prevention function>LQ³
PRO MODE´
Possible number of amplifiers for interference prevention function is
different as shown in table below.
5HVSRQVHWLPH
Interference
prevention function setting
H-SP FAST STD LONG U-LG +<35
02412
In case putting in more amplifiers than limit of interference prevention
IXQFWLRQSXWWKHDPSOL¿HUSURWHFWLRQVHDOWRDPSOL¿HUZKLFKLVDGMDFHQW
RIHQGRIDQDPSOL¿HUWKDWWKHLQWHUIHUHQFHIXQFWLRQLVYDOLGRUVHW2))LQ
FRPPXQLFDWLRQSURWRFROVHWWLQJRIWKHHQGRIDPSOL¿HUWKDWWKHLQWHUIHU-
ence prevention function is valid.
For comunicaton protocol setting procedure, refer < PRO4: communication
SURWRFROVHWWLQJ!LQ³ PRO MODE.´
([DPSOHSXWWLQJLQRIWKLVGHYLFHDQGVHW67'RIUHVSRQFHWLPHVHWWLQJ
Possble number of interference prevantion is 4. Put the amplifier
SURWHFWLRQVHDOVEHWZHHQWKDQGWKDPSOL¿HUVDQGEHWZHHQWKDQG
9th amplifiers or change the communication protocol setting of 4th
DQGWKWR2))VLQFHLQWHUIHUHQFHSUHYHQWLRQZRUNVIURPVWWRWK
IURPWKWRWKDQGWKWRWK
,QFDVHPRXQWLQJPRUHDPSOL¿HUVZKRVHUHVSRQVHWLPHVHWWLQJDUHGLIIHU-
HQWSXWSURWHFWLRQVHDOEHWZHHQDPSOL¿HUVWKDWKDYHGLIIHUHQWUHVSRQVH
WLPHVHWWLQJRUVHWFRPPXQLFDWLRQSURWRFROVHWWLQJRIWKHXSSHUDPSOL¿HU
to OFF.
For communication protocol setting procedure, refer to < PRO4: communication
SURWRFROVHWWLQJ!LQ³ PRO MODE´
16
CAUTIONS
This product has been developed / produced for industrial use only.
Make sure that the power supply is OFF while adding or removing the
DPSOL¿HUV
7DNHFDUHWKDWLIDYROWDJHH[FHHGLQJWKHUDWHGUDQJHLVDSSOLHGRULIDQ$&
power supply is directly connected, the product may get burnt or damaged.
Take care that short circuit of the load or wrong wiring may burn or dam-
age the product.
Do not run the wires together with high-voltage lines or power lines, or
put them in the same raceway.
This can cause malfunction due to induction.
7KHVSHFL¿FDWLRQPD\QRWEHVDWLV¿HGLQDVWURQJPDJQHWLF¿HOG
Verify that the supply voltage variation is within the rating.
If power is supplied from a commercial switching regulator, ensure that
the frame ground (F.G.) terminal of the power supply is connected to an
actual ground.
In case noise generating equipment (switching regulator, inverter motor,
etc.) is used in the vicinity of this product, connect the frame ground (F.G.)
terminal of the equipment to an actual ground.
7KHXOWUDORQJGLVWDQFH8/*+<35PRGHLVPRUHOLNHO\WREHDIIHFWHG
E\H[WUDQHRXVQRLVHVLQFHWKHVHQVLWLYLW\RIWKDWLVKLJKHUWKDQWKHRWKHU
modes. Make sure to check the environment before use.
Do not use during the initial transient time (H-SP, FAST, STD: 0.5 sec.,
/21*8/*+<35VHFDIWHUWKHSRZHUVXSSO\LVVZLWFKHG21
Make sure to use the quick-connection cable (optional) for the connec-
tion of the controller.
([WHQVLRQXSWRWRWDOPLVSRVVLEOHZLWKPP2 or more cable.
However, in order to reduce noise, make the wiring as short as possible.
Make sure that stress by forcible bend or pulling is not applied to the
VHQVRUFDEOHMRLQWDQG¿EHUFDEOH
This product is suitable for indoor use only.
Avoid dust, dirt, and steam.
Take care that the product does not come in contact with oil, grease, or-
ganic solvents such as thinner, etc., strong acid or alkaline.
7KLVSURGXFWFDQQRWEHXVHGLQDQHQYLURQPHQWFRQWDLQLQJLQÀDPPDEOH
RUH[SORVLYHJDVVHV
Never disassemble or modify the product.
7KLVSURGXFWDGRSWV((35206HWWLQJVFDQQRWEHGRQHPLOOLRQWLPHV
RUPRUHEHFDXVHRIWKH((3520¶VOLIHWLPH
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
•
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Ɣ
Group
A
Group
B
Group
D
Group
C
Communication direction
Group Model No.
AFX-301Ƒ
(Conventional version unit)
FX-301BƑGƑHƑLS-401Ƒ
BFX-301Ƒ0RGL¿HGYHUVLRQXQLW
FX-305ƑFX-301Ƒ-C1
CLS-403ƑDPS series
DFX-500 series
Communication direction
Interference
prevention
possible
range
Put a protection seals between
WKDQGWKDPSOL¿HU
Or set communication protocol
setting in 4th to OFF.
Put a protection seals between
WKDQGWKDPSOL¿HU
Or set communication protocol
VHWWLQJLQWKWR2))
Interference prevention
possible range
Interference prevention
possible range
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
17
SPECIFICATIONS
Type Series connection type
NPN output PNP output
Item
Model No.
FX-501 FX-501P
Supply voltage WR9'&5LSSOH33RUOHVV
Power consumption
Normal operation: 960mW or less (current consumption
40mA or less at 24V supply voltage)
(FRPRGHP:RUOHVVFXUUHQW FRQVXPSWLRQP$ RU
less at 24V supply voltage)
Sensing output
NPN open-collector transistor
0D[LPXPVLQNFXUUHQW
100mA (Note 1)
$SSOLHGYROWDJH9'&RUOHVV
(between sensing output and 0V)
5HVLGXDOYROWDJH
2V or less (Note 2)
[At 100mA (Note 1) sink current]
•
•
•
PNP open-collector transistor
0D[LPXPVRXUFHFXUUHQW
100mA (Note 1)
$SSOLHGYROWDJH9'&RUOHVV
(between sensing output and +V)
5HVLGXDOYROWDJH
2V or less (Note 2)
[At 100mA (Note 1) source current]
•
•
•
Output operation Switchable either Light-ON or Dark-ON
Short-circuit
protection
Incorporated
5HVSRQVHWLPH
+63ȝVRUOHVV)$67ȝVRUOHVV67'ȝVRUOHVV
/21*PVRUOHVV8/*PVRUOHVV+<35PVRUOHVV
Selectable
Timer function
Changeable in OFF-delay timer, ON-delay timer, One-shot
timer, ON / OFF-delay timer or ON-delay / One-shot timer
Switchable either effective or ineffective
7LPHUSHULRG!
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
$SSUR[PV$SSUR[WRPV
:KHQXVLQJWKHWLPHUUDQJH³VHF´VHWWLQJ
$SSUR[VHF$SSUR[WRVHF
:KHQXVLQJWKHWLPHUUDQJH³PV´VHWWLQJ
$SSUR[PV$SSUR[WRPV
Interference prevention
function
,QFRUSRUDWH1RWH
Ambient temperature
-10 to +55°C (If 4 to 7 units are mounted in cascade: -10 to
&RULIWRXQLWVDUHPRXQWHGLQFDVFDGHWR&
(No dew condensation or icing allowed)
Storage:
-
20 to +70°C
Ambient humidity WR5+6WRUDJHWR5+
Material
Enclosure: Heat-resistant ABS, Switch: TPEE
Operation key cover: Polycarbonate
Weight (Main body only)
$SSUR[J
Accessory
FX-MB1$PSOL¿HUSURWHFWLYHVHDOVHW
1RWHV  P$PD[LIRUPRUHVHULHVFRQQHFWLRQW\SHVDUHFRQQHFWHGWRJHWKHU
2) In case of using the quick-connection cable (cable length 5m) (optional).
 1XPEHURIVHQVRUKHDGVZKLFKLVSRVVLEOHWRPRXQWFORVHO\LQLQWHUIHUHQFHSUHYHQ-
tion function depends on response time like follows
 7KHFDEOHIRUDPSOL¿HUFRQQHFWLRQLVQRWVXSSOLHGDVDQDFFHVVRU\%HVXUHWRXVH
the optional cables given below.
6HULHVFRQQHFWLRQW\SH!
Cable
Cable length 1m Cable length 2m Cable length 5m
Main cable Sub cable Main cable Sub cable Main cable Sub cable
FX-501ƑCN-73-C1 CN-71-C1 CN-73-C2 CN-71-C2 CN-73-C5 CN-71-C5
18
INTENDED PRODUCTS FOR CE MARKING
7KHPRGHOOLVWHGXQGHU³ SPECIFICATIONS´FRPHVZLWK&(
Marking.
$VIRUDOORWKHUPRGHOVSOHDVHFRQWDFWRXURI¿FH
Ɣ
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Sunx FX-501 Series User manual

Brand
Sunx
Model
FX-501 Series
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents