Sunx FX-D1 User manual

Brand: Sunx

Model: FX-D1

Type: User manual

INSTRUCTION MANUAL

FX-D1 Series

Digital Setting Fiber Sensor

CAUTIONS

Make sure to carry out the wiring in the power supply off condition.

Verify that the supply voltage variation is within the rating.

In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity

of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.

If power is supplied from a commercial switching regulator, ensure that the frame

ground (F.G.) terminal of the power supply is connected to an actual ground.

Do not use during the initial transient time (0.5 sec.) after the power supply is switched on.

Do not run the wires together with high-voltage lines or power lines or put them in

the same raceway. This can cause malfunction due to induction.

Extension up to total 100m is possible with 0.3mm2, or more, cable. However, in

order to reduce noise, make the wiring as short as possible.

This sensor is suitable for indoor use only.

Avoid dust, dirt, and steam.

Take care that the product does not come in direct contact with organic solvents,

such as, thinner, etc.

This sensor cannot be used in an environment containing inflammable or explosive gases.

Never disassemble or modify the sensor.

PART DESCRIPTION

Output 1 operation indicator (Orange)

Output 2 operation indicator (Orange)

Jog switch

Mode selection switch

4 digit LCD (with back light)

JOG SWITCH FUNCTION

Press

3 sec. or

Tu r n

Jog switch FunctionOperation

࡮

In 2-level teaching, it sets the threshold value.

In limit teaching, it stores the incident light intensity in the object absent condition.

It changes the display of the current incident light intensity from absolute value

to percentage value or from percentage value to absolute value.

Each item is selected and the item and the contents of each item to be set is decided.

࡮

In limit teaching, it determines the direction of shift of the threshold value.

It does fine adjustment of the set threshold value.

Selection is made between Output 1 and Output 2.

The contents of each item are selected.

࡮

In full auto-teaching, it sets the threshold value.

It confirms the output operation and the timer setting conditions.

OUTPUT

Output

Description

Threshold value, output operation

and timer can be set for Output 1.

Threshold value, output operation

and timer can be set for Output 2.

LCD display

Please refer to ' SETTING OF THRESHOLD

VALUE' for the method of setting the threshold

value, ' SETTING OF EACH MODE' for the

output selection and the method of setting the

output operation and the timer.

Since the FX-D1 series incorporate two independent outputs, threshold value,

output operation and timer can be set for each of the two outputs.

SETTING OF THRESHOLD VALUE

When the mode selection switch is changed from 'SET' to 'RUN' or from

'MODE' to 'RUN', the set threshold value or the contents of each mode

setting are stored in an EEPROM. Since the EEPROM has a life time,

the threshold value setting cannot be done for more than 100,000 times.

Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable.

This is the method of setting the threshold value by teaching two levels, corresponding to

the object present and object absent conditions. Normally, setting is done as given below.

In case of 2-level teaching

If the jog switch is pressed continuously for 3 sec., or more, full auto-teaching is done.

If the mode selection switch is changed to 'RUN' when '˴˴' is being displayed on the

LCD display, the incident light intensity taught at Step Ԝ is not recorded.

Notes: 1)

࡮

Set the mode selection switch to 'RUN'.

The threshold value does not change even if the jog switch is operated.

࡮

If teaching is accepted, the read incident light intensity is displayed for 0.5 sec. approx., and the threshold

value is set to the middle value of the incident light intensity levels in the object present and object absent

conditions. After that, the judgement on the stability of sensing is displayed for 2.5 sec. approx.

After this, the threshold value is displayed.

࡮

In case stable sensing is possible: ' ' is displayed.

In case stable sensing is not possible: ' ' is displayed.

࡮If teaching is accepted, the read incident light intensity is displayed for 0.5 sec.

approx. Subsequently, ' ' is displayed on the LCD display. (Note 2)

࡮The jog switch is pressed in the object absent condition and released.

࡮

Press the jog switch in the object present condition and release it within 3 sec. (Note 1)

࡮

Set the mode selection switch to 'SET'.

The present threshold value is displayed.

࡮Set to either Output 1 or Output 2 by turning the jog switch to the '+' or the '

side.

Output 1

Output 2

LCD display

Description

Step

࡮Set the fiber within the sensing range.

࡮Set the mode selection switch to either 'RUN' or 'MODE'.

Thank you very much for using SUNX products. Please read this Instruction Manual

carefully and thoroughly for the correct and optimum use of this product. Kindly keep

this manual in a convenient place for quick reference.

Never use this product as a sensing device for personnel protection.

In case of using sensing devices for personnel protection, use

products which meet standards, such as OSHA, ANSI or IEC etc.,

for personnel protection applicable in each region or country.

WARNING

MOUNTING

Fit the rear part of the mounting section of the amplifier on the attached

amplifier mounting bracket (MS-DIN-2) or a 35mm width DIN rail.

Press down the rear part of the mounting section of the unit on the

attached amplifier mounting bracket (MS-DIN-2) or a 35mm width

DIN rail and fit the front part of the mounting section to the attached

amplifier mounting bracket (MS-DIN-2) or a 35mm width DIN rail.

Attached amplifier mounting

bracket or 35mm width DIN rail

How to mount the amplifier

Snap the fiber lock lever down.

Insert the fiber cables slowly into the inlets until they stop. (Note 1)

Return the fiber lock lever to the original position, till it stops.

Fiber lock

lever

Fiber

Beam-emitting part

Beam-receiving part

Notes: 1)

In case the fiber cables are not inserted to a position where they stop, the sensing range reduces.

However, in case of a flexible fiber, take care that it may bend inside the amplifier, during insertion.

With the coaxial reflective type fiber, such as, FD-G4 or FD-FM2, insert the single-core

fiber cable into the beam-emitting inlet and the multi-core fiber cable into the beam-receiv-

ing inlet. If they are inserted in reverse, the sensing accuracy will deteriorate.

How to connect the fiber cables

Push the amplifier forward.

Lift up the front part of the amplifier to remove it.

Take care that if the front part is lifted without pushing the amplifier forward,

the hook on the rear portion of the mounting section is likely to break.

Note:

How to remove the amplifier

I/O CIRCUIT DIAGRAMS

٨NPN output type

100mA max.

(Brown) +V

(Black) Output 1

(White) Output 2 (Note 2)

12 to 24V DC

r10%

(Blue) 0V

Users' circuitInternal circuit

Color code

Sensor circuit

Load

٨PNP output type

Symbols... D1, D2

ZD1, ZD2, ZD3, ZD4: Surge absorption zener diode

Tr 1, Tr2

Tr 3, Tr4

: Reverse supply polarity protection diode

: NPN output transistor

: PNP output transistor

(Brown) +V

(Black) Output 1

(White) Output 2

(Note 2)

(Blue) 0V

Users' circuitInternal circuit

Color code

100mA max.

12 to 24V DC

r10%

Sensor circuit

Load

Notes: 1)

Use the optional cable with a connector for the plug-in connector type.

Model No.: CN-54-C2 (cable length 2m), CN-54-C5 (cable length 5m)

In case the optional connector attached cable CN-54-Cغ is connected to

the plug-in connector type sensor, the color or the Output 2 wire is orange.

Connector pin

position

Output 1

Output 2

SPECIFICATIONS

Notes: 1)

If the LCD dispaly indicates ' ', please contact our office.

For the plug-in connector type, add suffix 'J' at the end of the model No. Model No.: FX-D1J, FX-D1PJ

For the cable length 5m type, add suffix '-C5' at the end of the model No. (only NPN

output type) Model No.: FX-D1-C5

0.2mm2 4-core cabtyre cable, 2m long

Cable

Emission frequency 1

0.65ms or less

Emission frequency 2

0.75ms or less

Emission frequency 3

0.5ms or less

Response

time

Light-ON or Dark-ON, selectable with jog switchOutput operation

Incorporated

Short-circuit protection

Output

(Output 1, Output 2)

PNP output

Current consumption 45mA or less

NPN open-collector transistor

࡮Maximum sink current: 100mA

࡮

Applied voltage: 30V DC or less (between output and 0V)

࡮

Residual voltage: 1V or less (at 100mA sink current)

0.4V or less (at 16mA sink current)

PNP

open-collector transistor

࡮

Maximum source current: 100mA

࡮

Applied voltage: 30V DC or less (between output and +V)

࡮

Residual voltage: 1V or less (at 100mA source current)

0.4V or less (at 16mA source current)

12 to 24V DCr10%˴Ripple P-P 10% or less

Supply voltage

FX-D1P

Model No. FX-D1

Item

Type NPN output

Enclosure: Heat-resistant ABS, Enclosure cover: Polycarbonate

Material

70g approx.

Weight

35 to 85% RH, Storage: 35 to 85% RH

Ambient humidity

Red LED (modulated)

Emitting element

Ambient temperature 0 to +50͠ (No dew condensation), Storage: -20 to +70͠

2-level teaching / Limit teaching / Full auto-teaching

Sensitivity setting

Incorporated

Timer function

4 digit LCD display (with back light)

Display

Incorporated (up to three sets of fibers can be mounted adjacently)

Interference prevention function

MS-DIN-2 (Amplifier mounting bracket): 1 No.

Accessory

٨Full auto-teaching is used when it is desired to set the threshold value without

stopping the assembly line, with the object in the moving condition.

In case of full auto-teaching

࡮

Set the mode selection switch to 'RUN'.

The threshold value does not change even if the jog switch is operated.

࡮

If teaching is accepted, the read incident light intensity is displayed for 0.5 sec. approx., and the threshold

value is set to the middle value of the incident light intensity levels in the object present and object absent

conditions. After that, the judgement on the stability of sensing is displayed for 2.5 sec. approx.

After this, the threshold value is displayed.

࡮

In case stable sensing is possible: ' ' is displayed.

In case stable sensing is not possible: ' ' is displayed.

࡮

Set the mode selection switch to 'SET'.

The present threshold value is displayed.

࡮Set to either Output 1 or Output 2 by turning the jog switch to the '+' or the '

side.

Output 1

Output 2

LCD display

Description

Step

࡮Set the fiber within the sensing range.

࡮Set the mode selection switch to either 'RUN' or 'MODE'.

࡮Press the jog switch continuously for 3 sec. or more with the object moving on

the assembly line.

࡮

' ' is displayed on the LCD display. Release the jog switch when the object has

passed.

Set the mode selection switch to either 'RUN' or 'MODE'.

Set to either Output 1 or Output 2 by turning the jog switch to the '+' or the '

' side.

Set the mode selection switch to 'SET'.

Press the jog switch in the condition when there is no object or background body.

If teaching is accepted, ' ' is displayed on the LCD display.

Once again, press the jog switch in the condition when there is no object or background body.

Set the mode selection switch to 'RUN'.

Note:

Please take care that, if the sensor is set to max. sensitivity, it becomes weak against extraneous light,

noise and optical interference.

In case of fine adjustment

࡮

Set the mode selection switch to 'RUN'.

The threshold value does not change even if the jog switch is operated.

࡮

Set the mode selection switch to 'SET'.

The present threshold value is displayed.

Output 1

Output 2

࡮Set to either Output 1 or Output 2 by turning the jog switch to the '+' or the '

side.

࡮Set the mode selection switch to either 'RUN' or 'MODE'.

LCD display

Description

Step

࡮

In case the threshold value is to be increased (sensitivity to be reduced), turn the

jog switch a little to the '+' side to increase the threshold value slowly. If the jog

switch is turned fully to the '+' side, the threshold value increases rapidly.

In case the threshold value is to be decreased (sensitivity to be increased), turn

the jog switch a little to the '

' side to decrease the threshold value slowly. If the

jog switch is turned fully to the '

' side, the threshold value decreases rapidly.

SETTING OF EACH MODE

In case only a part of the settings are to be changed, set the mode selection switch

to 'RUN', at the appropriate time, in the middle of the above procedure to make only

the required changes.

࡮Press the jog switch at the output operation desired to be set.

࡮Turn the jog switch to either the '+' or the '

' side. The bar display

alternates between Output 1 and Output 2.

(The bar display on the extreme left blinks.)

࡮Press the jog switch at the output desired to be set.

LCD display

Description

Step

Output

setting

Output operation

setting

Timer operation setting

Emission frequency

setting

࡮Set the mode selection switch to 'MODE'.

: Light-ON

: Dark-ON

(' ' or ' ' blinks.)

࡮Turn the jog switch to either the '+' or the '

' side. ' ' and ' ' are

displayed alternately.

࡮Press the jog switch at the timer operation desired to be set.

࡮Turn the jog switch to either the '+' or the '

' side. The display of timer

operation changes as given below.

(3 digits from the right side blink.)

ON-delay timer

OFF-delay timer

500ms 200ms 100ms 40ms

(Without timer)

500ms 200ms 100ms 40ms

The output operation set

at the 'output operation

setting' is displayed.

࡮Press the jog switch at the emission frequency desired to be set.

࡮After the modification of settings, the display returns to the initial display.

࡮Set the mode selection switch to 'RUN' after finishing the settings.

࡮Turn the jog switch to either the '+' or the '

' side. The display of emission

frequency changes as given below.

(The display changes and all digits blink.)

(Emission frequency 1) (Emission frequency 2)

(Emission frequency 3)

٨FX-D1 series incorporate an ON-delay timer, which is useful when sensing only

objects with a long passage time, and an OFF-delay timer, which is useful when

the sensor is connected to devices having a slow response time. The timer period

can be selected from four values: 40ms, 100ms, 200ms and 500ms.

Please refer to ' SETTING OF EACH MODE' for the setting method.

TIMER FUNCTION

Timer period: T=40ms, 100ms, 200ms, 500ms (selectable at the time of 'MODE' setting)

Timer operation

Normal

Light-ON

Dark-ON

Light-ON

Output

operation

Sensing

condition

ON-delay timer

OFF-delay timer

TTT

OFF

Light

Dark

٨Since the FX-D1 series incorporate an interference prevention function, up to 3

sets of fibers can be mounted close to each other by setting different emission

frequencies. Further, close mounting is also possible along with fibers which are

fitted to the fiber sensor amplifiers, FX-A1 series and FX-M1 series.

Please refer to ' SETTING OF EACH MODE' for the setting method.

However, note that the response time varies with the emission frequency as given below.

INTERFERENCE PREVENTION FUNCTION

Emission frequency

0.5ms or less

0.65ms or less

0.75ms or less

Response time

Note: Do not set the threshold value when interfering light is incident.

Correct incident light intensity cannot be taught in this condition.

Description

٨This is the method of setting the threshold value by teaching only the object absent

condition (incident light stable condition). This is used for detection in presence of a

background body or for detection of small objects.

If the jog switch is pressed continuously for 3 sec., or more, full auto-teaching is done.

If the mode selection switch is changed to 'RUN' when '˴˴' is being displayed on the

LCD display, the incident light intensity taught at Step Ԝ is not recorded.

Notes: 1)

In case of limit teaching

࡮

Set the mode selection switch to 'SET'.

The present threshold value is displayed.

Output 1

Output 2

࡮Set the mode selection switch to either 'RUN' or 'MODE'.

࡮

Set the mode selection switch to 'RUN'.

The threshold value does not change even if the jog switch is operated.

࡮If teaching is accepted, the read incident light intensity is displayed for 0.5 sec.

approx. Subsequently, ' ' is displayed on the LCD display. (Note 2)

࡮

Press the jog switch in the object present condition and release it within 3 sec. (Note 1)

࡮Set to either Output 1 or Output 2 by turning the jog switch to the '+' or the '

side.

࡮Set the fiber within the sensing range.

࡮

' ' is displayed on the LCD display.

After that, the threshold value is shown.

LCD display

Step

࡮

'+' side:

' side:

The threshold value is shifted to a

value approx. 15% lower (higher

sensitivity) than that set at Ԝ. Used

in case of thru-beam type fiber.

The threshold value is shifted to a

value approx. 15% higher (lower

sensitivity) than that set at Ԝ. Used

in case of reflective type fiber.

࡮Turn the jog switch to either the '+' or the '

' side.

15%

100%

OFF

Turn to '+' side

Turn to '

' side

Threshold

value

Threshold

value

Incident light

intensity with

object absent

OFF

High

Threshold

value

Low

PERCENTAGE DISPLAY

After setting the threshold value, the current incident

light intensity can be expressed as a percentage of the

threshold value so that the degree of margin can be

confirmed at a glance. If the jog switch is pressed when

the mode selection switch is set on 'RUN', the display

changes from absolute value to percentage value, and

0 to 999% is displayed. However, % (percent) is

expressed by ' ' and fractions are rounded off.

If the jog switch is pressed once again, the

display returns to absolute value.

Further, in case percentage display is desired

when the power supply is switched off, and then,

on again, change the mode selection switch once

to 'SET' or 'MODE', and then, set it back to 'RUN'.

Threshold

value

100%

Large

Light-ON

Dark-ON

Small

Incident light intensity

(percentage display)

࡮

The larger the difference between the

numerical values in the Light state and the

Dark state, more stable is the sensing.

Percentage display=

Current incident light intensity

¸Threshold value100(%)

Current incident

light intensity

PRINTED IN JAPAN

Head Office

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Phone: +81-(0)568-33-7211 FAX: +81-(0)568-33-2631

Overseas Sales Dept.

Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591

http://www.sunx.co.jp/

SUNX Limited

Sunx FX-D1 User manual

Brand: Sunx

Model: FX-D1

Type: User manual

Download PDF

report

Sunx FX-D1 User manual

Sunx FX-D1 User manual

Related papers

Other documents