Bonanza A-36
Specification:
Length :1632 mm(64.3")
Wing Span :2045 mm(80.5")
Wing Area :60.0 sq. dm
6.46 sq. ft
Wing Loading :106.7 g/sq. dm
34.9 oz/sq. ft
Flying Weight :6.4 kg(14.1 lbs)
Radio :6ch&9 servos
Engine :108 2-cycle
120 4-cycle
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)
This R/C airplane is not a toy!
132mm
Top view
Side View
20mm
20mm
RUDDER
3-way
pressure inlet
Air tank
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
3-way
pressure inlet
Switch
Air inlet
Strut
Strut
Strut
Quick release connector
Make sure to assemble retracts as instructed below.
Three wheel retract system
Quick release connector
Pressure reduction inlet
Ø1.7mm
Ø0.2mm
The status when the
gear up
Pull out length of 8mm
to make gear down
Air valve Air valve
3-way pressure inlet 5
1
Air tank
1
Air inlet
2
1
1
Air line (3000mm)
2
Quick release connector
Strut
( 90 )
1
Strut ( 110 )
Switch
Clevis
Rod (2X300mm)
1
1
1
Retainer
TP Screw(2.6x14mm) 2
Top view
Position for
right diagram.
ELEVATOR
Side View
30mm
30mm
Top view
25mm
25mm
35mm
AILERON
FLAP
Side View
FLAP
AILERON
Pleas notice the inner diameter for each
side of the pressure reduction inlet.
Please insure the sealing of the retract
system before flight .
Centre of Gravity.
Adjustment.
Adjustment.
Adjustment.
14
71
70
73
72
Steel wire
Copper joiner
Aluminum tube
Clevis
Add a rubber ring to the
clevis for insuring safety
Collar (5mm)
Collar (5mm)
Collar (5mm)
Two nacelle bottom covers are supplied for optional assembly of door,
which is decided by customers.Hardware package is not included.
TP Screw (2.3x12mm)
6
TP Screw (2.3x12mm)
Collar 4mm 3
4
Wooden Block
(25x15x13mm)
2
7
Collar (5mm)
Wheel (90mm)
Wooden supporter
(41.5x28x26mm)
Landing gear(5mm)
2
1
8
TP Screw (3x20mm )
Landing gear straps 2
Gear door
2
1
Landing gear (5mm)
1
Wheel (75mm)
Wooden supporter
(46x28x14mm) 1
4
TP Screw (2.6x14mm )
TP Screw (3x20mm)
Wooden Block
TP Screw (2.6x14mm)
Collar (5mm)
Wooden supporter
Collar (5mm)
6
TP Screw (2.3x12mm)
1
Ally nose arm
Epoxy the fixed laning gear to main wing.
Install the wheel to the nose gear.
Epoxy the fixed nose landing gear to the fuselage.
Trim the nacelle bottom cover and assemble it
with TP screws.
Installl the wheel and gear door to the landing gear.
65
66
67
68
69
13
65
Accessory list for the coming installation steps.
: 4-cycle .120
15"X7
Spinner nut
6
(with 9 servos),
6
6
6 channel radio for aiplane is highly recommended for this model.
Warning
Remove the covering with proper
pressure to cut through only the covering itself.Otherwise,
cutting down into the balsa structure may weaken the
model part and cause accident.
The pre-covered film on ARF kits may wrinkle due to
variations of temperature.Smooth out as explained right.
Pre-cover the covering with clean cloth!
Start at low setting. Increase the setting if
necessary.If it is too high,you may damage
the film.
Iow setting
with cover(cloth)
1.5mm
9
TP Screw (2.3x8mm)
Ply (15x15x3mm) 9
Epoxy plies inside the fuselage under the cowing and
mount the cowing with TP screw as illustration.
9
TP Screw (2.3x8mm)
Ply (15x15x3mm) 9
pvc part
1
pvc part
2
pvc part
2
pvc part
2
pvc part
2
Epxy the canopy to the fuselage.
Trim the cowling for engine and muffler.
Assemble the cowling .
Cut away the surplus parts of plastic cover
carefully along the shaded line.
The side view of the plane.
63
61
62
64
12
60
Accessory list for the coming installation steps.
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Make sure hinges are
mounted in the same line.
1mm
Aileron
Tailing
edge
Make sure they are in
the right position while
installing.
6
Pin hinge(24x24mm)
8
6
2
2
2
4
2
2
2
2
Clevis
Rod (2x300mm)
Retainer
TP Screw (2.3x12mm)
Wooden Block
(20x20x8mm)
Servo tray(68.5x56.5x2mm)
Pin hinge(24x24mm)
Screw (3x45mm)
Washer(3x15mm)
2
Washer(3x15mm)
Lock Nut (3mm )
Clevis
Retainer
Rod (2x300mm)
Screw (2x10mm)
Install the servo as the illustration below.
Install the nylon control horn and connect the linkage.
Apply instant type CA glue to aileron and pin hinge.
Keep some space about 1mm width between
aileron and trailing edge.
Assemble the aileron to main wing with instant type CA glue.Be careful
to ensure the moving parts of the hinges are able to move freely.
1
2
3
4
5
1
Accessory list for the coming installation steps.
1.5mm
2mm
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Flap
TP Screw (2.3x12mm)
Make sure hinges are
mounted in the same line.
1mm
Tailing
edge
Make sure they are in
the right position while
installing.
6
Pin hinge(24x24mm)
8
6
2
2
2
4
2
2
2
2
Clevis
Rod (2x300mm)
Retainer
TP Screw (2.3x12mm)
Wooden Block
(20x20x8mm)
Servo tray(68.5x56.5x2mm)
Pin hinge(24x24mm)
Screw (3x50mm)
Washer(3x15mm)
2
Washer(3x15mm)
Lock Nut (3mm )
Rod (2x300mm)
Clevis
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x35mm)
Screw (2x10mm)
Install the servo.
Secure the servo. Install the nylon control horn
and connect the linkage.
Apply instant type CA glue to flap and pin hinges.
Keep some space about 1mm width between
trailing edge and flap.
Assemble the flap to main wing with instant type CA glue. Be careful to
ensure the moving parts of the hinges are able to move freely.
7
68
9
10
2
Accessory list for the coming installation steps.
TP Screw (2.3x8mm)
1.5mm
8
TP Screw (2.3x8mm)
Ply (15x15x3mm) 8
Clevis
Rod (2X300mm)
1
1
1
1
Retainer
Ring
10mm
1mm
Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
2
2
Clevis
Copper joiner
2
2
Screw (2x10mm)
Nut (2mm )
2
Washer(2x5mm)
Steel wire
Copper joiner
Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
Install the servo of rudder .
Elevator servo
Rudder servo
Nose gear servo
Throttle servo
Switch servo
The sketch map when the servos install completion.
Mount the receiver and the battery in the fuselage.
Install the nylon control ring for switch and
connect the linkage.
Assemble the tail gear cover with screw.
Install the servo of elevator and make sure the pushrod
can't be pulled out from the copper joiner.
Customer can drill a hole to the copper joiner and fix a pin
in it for stopping the pushrod from pulling out.
55
54
56
58
57
11
59
22mm
3mm
2
Plastic tube(3x850mm)
3mm
145mm
10mm
10mm
5mm
Metal arms
Ball joint
Pin
Fiberglass pushrod
10mm
1mm
Copper joiner
Epoxy the fiberglass pushrod to relevant
position in the fuselage.
Fiberglass pushrod(3x895mm)
1
4
Copper joiner
2
Plastic tube(3x850mm)
4
Ply(20x16x2mm)
2
4
Copper joiner
Aluminum tube(3x6mm)
2
Steel wire (0.5x1500mm)
4
2
2
2
Clevis
Retainer
Washer(3x15mm)
Lock Nut (3mm )
1
Screw (3x80mm)
2
Clevis
2
Screw (2x10mm)
2
Nut (2mm )
2
Washer(2x5mm)
Washer(3x15mm)
Screw (3x80mm)
Lock Nut (3mm )
Clevis
Aluminum tube
Steel wire
2
Steel wire (0.5x1200mm)
1
3
2
2
Clevis
Retainer
Washer(3x15mm)
Lock Nut (3mm )
1
Screw (3x80mm)
2
Copper joiner
Rod (2X300mm) 1
The sketch map after the rudder shaft assemble finished.
Assemble the plastic tubes through the holes in the frame,epoxy
them and Cut off the surplus parts as show in the illustration.
Drill a hole to appropriate position in the rudder
and assemble the rudder shaft.
Epoxy the fiberglass pushrod to the copper joiner tightly.
Customer can drill a hole to the copper joiner and fix a pin
in it for stopping the pushrod from pulling out.
49
50
52
53
10
51
Accessory list for the coming installation steps.
1.5mm
3mm
TP Screw (2.3x12mm)
Note:rubber wheels oleo struts
and retracts are optional.
Retracts strut
Screw (3x10mm)
Gear door
Washer(3x6mm)
Main wing joiner 1
1
2
Gear door
2
Wheel (90mm)
8
TP Screw (2.6x14mm)
Washer(3x6mm)
2
2
Wood dowel (6x50mm)
2
Wood dowel (6x30mm)
2
2
Blind Nut (6mm)
Screw (6x50mm)
Screw (3x10mm) 8
8
LockNut (4mm)
LockNut (4mm)
4
Wooden Block(25x15x13mm)
Wooden Block
Clevis
Retainer
Rod (2x300mm)
Rod (2x300mm)
Clevis
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x35mm)
Screw (2x10mm)
Screw (2x10mm)
2
Bushing (8X6mm)
Bushing (8X6mm)
8
TP Screw (2.6x14mm)
TP Screw (2.6x14mm)
1.5mm
Secure the air retracts gear with typer screw.
Washer(3x6mm)
Washer(3x6mm)
8
6mm
2
Wood dowel (6x30mm)
1
Rib template (2mm ply)
Rib template (2mm ply)
Rib template (2mm ply)
According to the rib template drill holes in one wing and
epoxy wood dowel in them.
Secure the flap servo. Install the nylon control
horn and connect the linkage.
Assemble the wheel and the gear door to the retract.
Install the nylon control horn and connect the linkage.
12
13
11
15
3
Accessory list for the coming installation steps.
14
90 mm
24 mm
2
Wood dowel (6x50mm)
6mm
Main wing joiner
1
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
B'
B
C=C'
B=B'
Make sure to glue securely.
If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming off during flights,
you'll lose control of your airplane which leads
to accidents!
C'
C
6.2mm
Blind Nut
2
2
Blind Nut (6mm)
Screw(6x50mm)
90 mm 25 mm
6mm
Epoxy the main wing together.
Drill holes at appropriate position in the wing for
fetching out the servo line and air pipe.
Drill two holes to appropriate position in the
wing and epoxy the wood dowel in it.
Assemble the main wing separately and
be sure with the right way.
Mount the main wing to the fuselage.
Drill two holes to relevant position in the fuselage
for installing the main wing.
17
18
19
20
21
4
16
Fuel tank (550cc) 1
Linkage Stopper
Washer (2mm)
Washer (2mm)
Nut (2mm)
Set screw (3x4mm)
Washer (
2mm
)
Set screw (3x4mm)
1
1
1
1
Fuel supply line
Fuel spray line
Air pressure line
Set Screw (3x4mm)
Set Screw (2mm)
Rod (2x400mm)
Set Screw (2mm)
Washer (2mm)
Linkage Stopper
1
1
1
1
1
4
4
Washer (4x8mm)
4
Rod (2x400mm)
Blind Nut (4mm)
Screw (4x25mm)
Set Screw (3x4mm)
Assemble the servo and switch.
Mount the servo and switch in the fuselage.
Assembly of the fuel tank.
Mount the fuel tank into the fuselage.
Assemble the accelerator push rod to nose engine.
Assemble the accelerator push rod to nose engine.
44
45
46
47
48
9
43
Washer (4x8mm)
Screw (4x25mm)
Washer (4x8mm)
Washer (4x8mm)
Screw (4x35mm)
Spring Washer (4mm)
Nut (4mm)
4mm
In case of 2-cycle & 4-cycle engine.
Ply (15x15x2mm) 2
Ply (15x15x2mm)
4
Blind Nut (4mm)
5.2mm
Blind Nut
153mm
Fuel tank (550cc) 1
TP Screw (2.3x8mm) 5
1
Engine mount (68x105mm)
Linkage Stopper
4
4
12
4
Washer(4x8mm)
Screw (4x35mm)
Spring Washer (4mm)
Nut (4mm)
4
Screw (4x25mm)
2
Plastic tube (2x400mm)
4
Blind Nut (4mm)
2
Ply (15x15x2mm)
Two nacelle bottom covers are supplied for optional assembly of door,
which is decided by customers.Hardware package is not included.
TP Screw (2.3x12mm)
6
TP Screw (2.3x12mm)
2
5mm
Assemble the engine.
The front view when the engine install completion.
Drill four holes at the diameters as shown for
engine mount.
The side view when the engine install completion.
Install the bottom cover.
39
40
41
42
8
38
Accessory list for the coming installation steps.
1
6
Pin hinge(24x24mm)
Stab joiner
(12x230mm)
B'
B
A=A'
B=B'
Make sure to glue securely.
If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming off during flights,
you'll lose control of your airplane which leads
to accidents!
AA'
4
Matal douel (4x30mm)
1
Rib template (3mm ply)
4mm
1
Rib template (3mm ply)
A ccording to thr rib template drill holes to the tail of
fuselage as below.
3
Pin hinge(2.5x48mm)
4mm
4
Wood dowel (4x30mm)
Drill two holes at the stabilizer root base via rib template
and epexy the wood dowel in them.
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
1
Stab joiner (12x230mm)
1
1
Screw (2x10mm)
Nut (2mm )
1
Copper ball (2mm )
U-style wire
2mm
Metal arms
Screw (2x10mm)
Nut (2mm )
Copper ball
Trim the shaded section
1
U-style wire (150x3mm)
1
U-style wire (150x3mm)
Assemble horizontal tail separately and be sure
with the right way.
Assemble the stablilizers carefully to fuselage.
Set the U-style wire through the tail of fuselage as
below.
22
23
24
25
26
5
Accessory list for the coming installation steps.
3
Pin hinge(2.5x48mm)
2.5mm
Make sure hinges are
mounted in the same line.
1mm
Rudder
Tailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Keep some space about 1mm width between
the tailing edge and the rudder.
Drill holes to appropriate position in the rudder and epoxy
the ping hinges in them
Drill slots to appropriate position in the stabilizer .
2x12mm
Make sure hinges are
mounted in the same line.
6
Pin hinge(24x24mm)
Apply instant type CA glue to pin hinges and elevator.
Elevator
1mm
Tailing
edge
Make sure they are in
the right position while
installing.
Keep some space with 1mm width between
the tailing edge and elevator.
3mm
Glue the elevator to the stabilizer by CA and epoxy.
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
3mm
34mm
103mm 103mm
28
27 30
31
29
6
32
2.5mm
Drill holes to the relevant position in the tailing edge
and epoxy the rudder to them.
Note:rubber wheels oleo struts
and retracts are optional.
Retracts strut
Nut (4mm)
1.5mm
4
TP Screw (2.6x14mm)
TP Screw (2.6x14mm)
2
Steel wire (0.5x1500mm)
2
Clevis 4
TP Screw (2.6x14mm) 6
TP Screw (2.3x12mm)
2
Plastic tube(3x50mm)
1
Nut (4 mm )
1
Wheel (75mm)
2
2
Copper joiner
Aluminum tube(3x6mm)
2
Clevis
2
2
Screw (2x10mm)
Nut (2mm )
2
2
2
Clevis
Copper joiner
Aluminum tube(3x6mm)
2
2
Screw (2x10mm)
Nut (2mm )
2
Washer(2x5mm)
Steel wire
Copper joiner
Aluminum tube Lock Nut (2mm )
Screw (2x10mm)
Ball joint
Washer(2x5mm)
2
Nut (2mm )
2
Washer(2x5mm)
1
Bushing (8X6mm)
Bushing (8X6mm)
Trim a small slot to appropriate
position in the whell shaft and
fixing the shaft by set screw.
Assemble the wheel to the nose retract.
Install the nose retract .
Assemble the servo in the fuselage.
Install the servo of nose gear.
33
37
35
36
34
7
Accessory list for the coming installation steps.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
GREAT PLANES GPMA1154 Owner's manual
-
ESM Douglas SBD-5 Dauntless User manual
-
Troy Built Models Aichi D3A1 User manual
-
Troy Built Models B-25 Mitchell User manual
-
Troy Built Models FAIREY SWORDFLSH User manual
-
Hangar 9 Spitfire Mk.IX ARF User manual
-
ESM F - 4u Corsair User manual
-
Royal Aircraft SE 5a User manual
-
VQ Models Messerschmitt BF-109 User manual
-
HobbyKing SBACH 55" User manual
