40mm
40mm
AILERON
Adjustment of the aileron and flap,be sure they can work
perfectly.
50mm
50mm
Top view
RUDDER
Side View
Adjustment of the rudder, be sure it can work perfectly.
Glue the scale exhaust to the cowling,and clue the
exhaust tube to the exhaust as illustration.
Fix the exhaust tube via Plastic plate and screws.
Top view
Position for
right diagram.
ELEVATOR
40mm
40mm
Adjustment of the elevator,be sure it can work perfectly.
130mm
130mm
Centre of the Gravity.
Screw
Nut
4
4
Screw (2x10mm)
4
4
Nut (2mm )
TP Screw (2.3x8mm)
Plastic plate
2mm
AILERON
AILERON
AILERON
AILERON
71
72
69
73
74
14
70
SE 5A
Specification:
Length :1397 mm(55")
Wing Span :1803 mm(71")
Wing Area :113sq.dm
12.2sq.ft
Wing Loading :56.6g/sq.dm
18.6oz/sq.ft
Flying Weight :6.4kg(14.1lbs)
Radio :6ch & 5servos
Engine: :26cc-36cc
SAFETY PRECAUTIONS
INSTRUCTION MANUAL
First-time builders should seek advice from people having building
experience.If misused or abused,it can cause serious bodily injury
and damage to property.
Fly only in open areas and preferably at a dedicated R/C flying site.
We suggest having a qualified instructor carefully inspect your
airplane before its first flight.Please carefully read and follow all
instructions included with this airplane,your radio control system
and any other components purchased separately.
(The people under 18 years old is forbidden from flying this model)
This R/C airplane is not a toy!
: 4-cycle .120
15"X7
6
(with 8 servos),
6
6
6 channel radio for aiplane is highly recommended for this model.
Warning
Remove the covering with proper
pressure to cut through only the covering itself.Otherwise,
cutting down into the balsa structure may weaken the
model part and cause accident.
The pre-covered film on ARF kits may wrinkle due to
variations of temperature.Smooth out as explained right.
2.5 in Spinner
Pre-cover the covering with clean cloth!
Start at low setting. Increase the setting if
necessary.If it is too high,you may damage
the film.
Iow setting
with cover(cloth)
Assemble the cowling carefully to the head of fuselage
with TP screws.
Glue the PVC parts to appropriate position on the cockpit.
Assemble the cockpit to the fuselage via screws as
illustration.
Screw (3x20mm)
TP Screw (2.3x8mm)
LockNut(5mm)
TP Screw (2.3x8mm)
Ply (3mm)
Ply (3mm)
PVC
PVC
Wheel (150mm)
Washer (3x6mm)
2mm
TP Screw (2.3x12mm)
Fix the undercarriage to the fuselage with gear plates and
TP screws.
Assemble the scale wheels to the model throught the rod shaft.
14
TP Screw (2.3x8mm)
2mm
4
4
Screw (2x10mm)
4
18
Nut (2mm )
TP Screw (2.3x8mm)
Plastic plate
Screw (3x20mm)
Washer (3x6mm)
4
4
66
13
64
67
65
68
Accessory list for the coming installation steps.
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
8
2
2
2
Rod (2.5x300mm)
TP Screw (2.3x12mm)
Servo tray(70x58x2mm)
Pin hinge(4.5X67mm) 6
Install the aileron servo to the servo mount as
illustration below.
Install the nylon control horn and connect the linkage.
1mm
Trailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Aileron
Collar (2.5mm)
2
2
2
2
Screw (3x15mm)
Nut (3mm )
Clevis
Control horn
8
Pin hinge(4.5x67mm)
Make sure hinges are
mounted in the same line.
Nut
Clevis
Washer 3x8mm
Screw 3x15mm
Collar
Apply instant type AB glue to appropriate position in the
trailing edge and assemble the ailerons to them.
Apply instant type AB glue to appropriate position of the aileron and
pivot & round hinges. Insert the pivot & round hinges to the ailerons.
Keep about 1mm width space between the aileron and
the trailing edge.
Accessory list for the coming installation steps.
1
2
3
4
5
1
Accessory list for the coming installation steps.
Mount the receiver and battery to appropriate position in
the fuselage.
Main landing gear
LockNut (5mm)
2
Collar (5mm)
2
1
TP Screw ( 2.3x8mm)
Gear plate
16
TP Screw ( 2.3x12mm) 8
4
Aluminum plate 2
2
Ply (3mm) 4
Fuel supply line
Fuel spray line
Air pressure line
Assembly of the fuel tank.
Fix the fuel tank to appropriate position in the fuselage
with cable tie.
Assemble the Aluminum platea to the undercarriage as
illustration.
Assemble the rubber bands around the landing gear,put the rod shaft
through the slots in the aluminum plate and the holes in the wood plate
as illustration.
cable tie
cable tie
cable tie 2
Rod (5x445mm)
Rod (2x100mm)
Collar (5mm)
Rubber bands
1
Rod (5x445mm)
4
Rod (2x100mm)
Rubber bands
Wheel (150 mm)
2
61
62
63
12
59
60
The standard sketch map when the kit install completion.
Insert the main wing joiner to one side of the lower wing.
Assemble the lower wing to the fuselage and insert the other
side lower wing to the fuselage through the main wing joiner.
Fix the wing to fuselage with screws throught the holes
applied in the wings and fuselage.
1
Main wing joiner (16x499mm)
2
Washer (6x12mm)
2
Screw (6x20mm)
Make sure to glue securely.
If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming off during flights,
you'll lose control of your airplane which leads
to accidents!
AA ’
A=A'
B=B'
B
B ’
Main wing joiner (16x499mm)
Screw
Spring Washer
2
Washer (6x12mm)
2
Screw (6x20mm)
1
Main wing joiner (16x499mm)
Apply instant type AB glue to the control horn and the slots in
the aileron, insert the control horn to the slots as illustration.
6
7
8
9
10
2
Accessory list for the coming installation steps.
Linkage Stopper
Washer (2mm)
Washer (2mm)
Nut (2mm)
Set screw (3x4mm)
Washer (
2mm
)
Set screw (3x4mm)
1
1
1
1
The sketch map when the engine install completion.
Install the servo of the throttle.
Assenble the servo in the fuselage
Set Screw (3x4mm)
Set Screw (2mm)
Rod (2x250mm)
Set Screw (2mm)
Washer (2mm)
Linkage Stopper
1
1
1
1
1
4
4
Washer (4x8mm)
4
Rod (2x250mm)
Blind Nut (5mm)
Screw (4x25mm)
Set Screw (3x4mm)
Assemble the throttle linkage.
Install the engine mount tubes to the fuselage,lock them
from inside of the fuselage.
Assemble the engine to the fuselage via the engine
mount tubes and screws.
4
Washer(4x8mm)
4
Screw (4x45mm)
Washer(4x8mm)
Screw (4x45mm)
Screw (4x20mm)
Washer(4x8mm)
4
Washer(4x8mm)
4
Screw (4x20mm)
55
54
58
56
57
11
55
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Pin hinge(4.5X67mm) 6
1mm
Trailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Aileron
8
Pin hinge(4.5x67mm)
Make sure hinges are
mounted in the same line.
A A"
A = A"
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Main wing joiner 2
16
B
C
B ’
A
A ’
C ’
A=A'
B=B'
C=C'
2
Wing skids
2
Wing skids
2
Wing skids
2
Wing skids
2
Wing skids
2
Wing skids
The sketch map when the upper wing assemble completion.
Assemble the upper wings to the upper centre wing.
Screw (3x16mm)
4
Screw (3x16mm)
Washer(3x6mm) 20
Nut (3mm)
Steel wire(0.5x3000mm) 12
4
16
Aluminum tube
Apply instant type AB glue to appropriate position in the
trailing edge and assemble the ailerons to them.
Apply instant type AB glue to appropriate position of the aileron and
pivot & round hinges. Insert the pivot & round hinges to the ailerons.
Keep about 1mm width space between the aileron and
the trailing edge.
Accessory list for the coming installation steps.
3
11
13
14
1512
Accessory list for the coming installation steps.
1
Engine mount (60x5mm)
Linkage Stopper
12
4
Washer(4x8mm)
Screw (4x45mm)
2
4
Screw (4x20mm)
4
4
Plastic tube (2x400mm)
Fuel tank (550cc) 1
1
Cable tie 2
Rod (2x250mm)
Blind Nut (4mm)
Make sure to glue securely.
If not properly glued, a failure in flight may occur.
Temporarily fasten down the main wing and
check its correct position.
Securely glue together.If coming off during flights,
you'll lose control of your airplane which leads
to accidents!
The standard sketch map when the kit install completion.
A A ’
A = A’
B = B’
B B ’
Link the wires of the elevator to the servo,assemble the
elevator servo to appropriate position in the fuselage.
Elevator servo
Rudder servo
Drill four holes at the diameters as shown for engine
mount.
160mm
4.2mm
The front view once the engine install completion.
The side view once the engine install completion.
53
51
52
10
50
49
Screw (3x16mm)
Nut 3mm
Washer (3x6mm)
Screw (3x16mm) Screw (3x16mm)
Nut 3mm Washer (3x6mm)
Washer (3x6mm)
Please adjust to the right position before epoxy
the wing skids into the slots in the wings!
Steel wire
Steel wire
Aluminum tube
Aluminum tube
Fix the wing struts of the centre wing to the centre
wing & fuselage as illustration.
Adjust the wing strut between the upper wing and lower
wing, epoxy the wing skids to slots in the upper wings.
Epoxy the wing skids to slots in the lower wing.
Fix the wing struts to the appropriate position between the
upper wings and lower wings.
The sketch map of the steel wire using for the wings.
Fix the wing struts of the centre wing to the centre
wing & fuselage as illustration.
17
16
20
19
18 21
4
Screw2x10mm
Washer (2x6mm)
Nut (2mm)
Epoxy the rudder to the vertical fin.
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Epoxy the control horn to the slots in the rudder.
Assemble the linkage rods for rudder
Rudder wooden pushrods
Elevator wooden pushrods
The sketch map of the pushrods for the rudder in the
fuselage.
Lock Nut (2mm )
Screw (2x10mm)
Clevis
Washer(2x6mm)
Asseble the linkage to the servo of the rudder.
lock the linkage to the control horn with screw and nut.
45 48
46
47
9
43
44
Fix the steel wires to the blind nud which applied in the
fuselage and wings with screws.
Assemble the linkage to the control horn in the lower wing's
aileron with screw and nut as illustration.
Assemble the arms in the ailerons in the bottom of the
upper wings.
The sketch map once the upper wing aileron and lower wing
aileron connected,and make sure they can move freely.
Washer(3x6mm)
4
4
Screw (3x16mm)
Steel wire
Aluminum tube
Accessory list for the coming installation steps.
Drill holes in appropriate position in the upper wing & lower
wing's ailerons as illustration.
2
2
2
4
4
Clevis
Rod (2x300mm)
Retainer
Washer(3x15mm)
4
Washer(3x15mm)
4
Plastic arms
Lock Nut (3mm )
122mm
25mm
135mm
25mm
3mm
4
Screw (3x30mm)
Rod (2x300mm)
Clevis
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x30mm)
Screw (2x10mm)
Washer(3x15mm)
Washer
Lock Nut (3mm )
Screw (3x30mm)
Rod (2x300mm)
upper wing
lower wing
22
23
24
5
25
26
Screw (3x20mm)
Nut 3mm
Washer (3x6mm)
Steel wire
Steel wire
1mm
Trailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Keep some space about 1mm width between the rudder
and tail edge.
Rudder
The sketch map of the steel wires work for stabilizer. Assemble the tail wheel to the rudder as illustration.
Fix the steel wires in the stabilizer.
Tail landing gear(2mm)
Steel wire
Aluminum tube
Screw (3x20mm) Nut 3mm
Washer (3x6mm)
Accessory list for the coming installation steps.
3
Pivot & round hinges(2.5x48mm)
1
2
2
2
Washer(2x6mm)
2
Washer(3x6mm)
Wooden pushrods (8x550mm)
Heat-shrink tude
Rod (2x300mm)
2
2
2
Clevis
Nut (2mm )
1
Nut (3mm )
Screw (2x10mm)
Control horn 1
1
Screw(3x20mm)
1
Tail wheel (30mm)
Apply instant type AB glue to appropriate position of the rudder and
pivot & round hinges. Insert the pivot & round hinges to the rudder.
Make sure hinges are
mounted in the same line.
39
40
38
41
8
42
1
U-style wire(3mm)
Accessory list for the coming installation steps.
Link the upper wing aileron and lower wing aileron via the
rods and retainers
U-style wire(3mm)
Apply instant type AB glue to appropriate position of the elevator and
pivot & round hinges. Insert the pivot & round hinges to the elevator.
Make sure hinges are
mounted in the same line.
1mm
Trailing
edge
Cut away the rubber tube when
the epoxy glue dried.
Make sure they are in
the right position while
installing.
Keep about 1mm width space between the elevators
and the stabilizers.
Elevator
6
pivot & round hinges(2.5x48mm)
6
Pivot & round hinges(2.5x48mm)
Securely glue together. If coming off during flights, you 'll
lose control of your airplane which leads to accidents!
Assemble the elevators to the stabilizers via pivot & round hinges.
AsPut the U-style wire and stabilizer through the slot in the
fuselage tail and epoxy the stabilizer steadily in it.
1
1
2
2
2
Washer(2x6mm)
18
Washer(3x6mm)
Wooden pushrods (8x550mm)
Heat-shrink tude
Rod (2x300mm)
2
2
Clevis
9
Nut (3mm )
2
Nut (2mm )
Screw (2x10mm) 9
Screw (3x20mm)
10
Steel wire (0.5x700mm)
Control horn 1
Retainer
Rod (2x300mm)
18
Aluminum tube
27
28
29
6
30
31
Screw (2x10mm)
Nut (2mm)
Washer (2x6mm)
Assemble the linkage rods for elevator
Lock Nut (2mm )
Screw (2x10mm)
Clevis
Washer(2x6mm)
Asseble the linkage to the servo of the elevator.
Elevator wooden pushrods
The sketch map of the pushrods for the elevator in the
fuselage.
Epoxy the control horn to the slot in the elevator as
illustration.
lock the linkage to the control horn with screw and nut.
Assemble the elevator servo in the fuselage and connect
the linkage.
32
7
34
33
37
36
35
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Troy Built Models FAIREY SWORDFLSH User manual
-
Troy Built Models B-25 Mitchell User manual
-
BONANZA A-36 User manual
-
E-flite Boeing Stearman PT-17 User manual
-
HobbyKing SBACH 55" User manual
-
ESM Douglas SBD-5 Dauntless User manual
-
ESM F - 4u Corsair User manual
-
Hangar 9 Spitfire Mk.IX ARF User manual
-
Troy Built Models Aichi D3A1 User manual
-
Black Horse Model Fieseler Fi156C STORCH Instruction Manual Book
