Contec SH-9008AT-POE is an unmanaged Gigabit Ethernet Switch HUB with PoE function. It supports IEEE802.3/IEEE802.3u/IEEE802.3ab/IEEE802.3af/IEEE802.3at standards and offers data transfer rates of 10Mbps/100Mbps/1000Mbps. With its 8-port 10/100/1000 Base-T compatible HUB, it allows for seamless data transmission and network expansion. The device operates within a temperature range of -35 to +70°C, making it suitable for various environments.
Contec SH-9008AT-POE is an unmanaged Gigabit Ethernet Switch HUB with PoE function. It supports IEEE802.3/IEEE802.3u/IEEE802.3ab/IEEE802.3af/IEEE802.3at standards and offers data transfer rates of 10Mbps/100Mbps/1000Mbps. With its 8-port 10/100/1000 Base-T compatible HUB, it allows for seamless data transmission and network expansion. The device operates within a temperature range of -35 to +70°C, making it suitable for various environments.
Product Guide
CONTEC CO., LTD.
3
-
9
-
31, Himesato, Nishiyodogawa
-
ku, Osaka 555
-
0025, Japan
http
s
://www.contec.co
m
/
No part of this document may be copied or reproduced in any form by any means
without prior written consent of CONTEC CO., LTD.
NA07243 (LYXZ521)
[
0
4
14
2020
]
April
20
20
Edition
Industrial 8-port unmanaged Gigabit PoE Ethernet Switching HUB
SH-9008AT-POE
Thank you for purchasing this product. The product you have purchased consists of the
following items.
Check, with the following list, that your package is complete.
If you find any item either missing or damaged, please contact the sales representative you
purchased the product from.
Read the Reference Manual, Please use correctly this product.
The following manuals come with this product. Visit our website and download them by
entering the model type in "Downloads". Read them before using the product.
Before using the product, be certain to read the following guide, manual. They can be
downloaded from Contec website.
Name
Contents
How to get
Product Guide (
T
his sheet)
This lists the product configuration and
describes the precautions.
Included in the package
(Printed matter)
Reference Manual
This describes the hardware aspects such
as functions and settings.
Download
(PDF)
Download
https://www.contec.com/download/search/
1. About the Product
This product is an unmanaged Gigabit Ethernet Switch HUB with PoE function. A wide range
of power input from 12 to 57VDC can be supported and the product has 8-port
10/100/1000 Base-T compatible HUB.
The product is capable of operating in the temperature between -35 and + 70°C.
2. Product Configuration
This product consists of the items listed below.
Check, with the following list, that your package is complete. If you discover damaged or
missing items, contact your retailer.
Product...1 Product Guide...1
Warranty
Certificate...1
DIN
-
Rail Mounting
Bracket...1
(attached to the
product
)
Power Connector
...1
RJ45
Protection Cap
...
8
Screw
…
8
Wall Bracket
...2
3. Safety Precautions
Understand the following definitions and precautions to use the product safely.
The caution mark " " on the face of the product indicates that you should always check
the meanings of the symbol described in the “Reference Manual”, and this is available in
our website. Visit < https://www.contec.com/download/> to download.
Safety Information
This document provides safety information using the following symbols to prevent
accidents resulting in injury or death and the destruction of equipment and resources.
Understand the meanings of these labels to operate the equipment safely.
DANGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
CAUTION
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury or in property damage.
Handling Precautions
DANGER
Always check that the power is turned off before connecting or disconnecting power
cables.
Do not modify the product.
Do not use the product in locations exposed to a flammable or corrosive gas. It may
cause explosion, fire, electrical shock, or malfunction.
Do not allow this device to come into contact with foreign substances (metal particles,
flammable substances, liquids, etc.) This can cause fire or electrical shock.
Do not place this device in an unstable location or use incomplete mountings. This may
cause the device to fall.
Be sure to connect the product to the stipulated power supply voltage. Connecting to a
different voltage might cause a fire or electrical shock.
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
This product is not intended for use in aerospace, space, nuclear power, medical
equipment, or other applications that require a very high level of reliability. Do not use
the product in such applications.
If using this product in applications where safety is critical such as in railways, automotive,
or disaster prevention or security systems, please contact your retailer.
CAUTION
Do not use or store the product in a location exposed to extremely high or low
temperature or susceptible to a rapid temperature changes.
Example: - Exposure to direct sun
- In the vicinity of a heat source
Do not use the product in extremely humid or dusty locations. It is extremely dangerous
to use this product with its interior penetrated by water or any other fluid or conductive
dust. If this product must be used in such an environment, install it on a dust-proof
control panel, for example.
Avoid using or storing the product in locations subject to shock or vibration that exceeds
range of specification.
When transporting the product, take suitable measures to avoid applying shock or
vibration directly to the product.
Impact resistance: 15G (11ms) below.
Use the product in the specified operating condition (temperature, humidity, vibration
and shock).
The product should always be grounded (earth).
Avoid installing in the place where ventilation of the product may compromise.
Insufficient aeration could heat up the product and lead to malfunctions or damages.
Do not use the product in the vicinity of devices that generate strong magnetic force or
noise. Such products will cause the product to malfunction (stop, reboot).
Do not use or store the product in the presence of chemicals.
When removing connectors or cables, always unplug the power cables connected to the
product first.
Do not modify the product. CONTEC will bear no responsibility for any problems, etc.,
resulting from modifying the product.
In the event of failure or abnormality (foul smells or excessive heat generation), unplug
the power cables from an electric outlet immediately and contact your retailer.
To connect with peripherals, use a grounded, shielded cable.
To clean the product, wipe it gently with a soft cloth dampened with either water or mild
detergent. Do not use chemicals or a volatile solvent, such as benzene or thinner, to
prevent the paint to be scraped or discolored.
When connecting cables, first check the shapes of connectors, and then insert them in
the correct orientation. After they are connected, do not put too much load on the
connected part. Doing so may result in poor contact or damage to the product and the
connected part.
Do not touch metal parts or terminals with your hands when the product is in operation.
Otherwise, the product may malfunction, or cause failure.
Do not touch the product or connectors with a wet hand to avoid electric shock.
The specifications of the product are subject to change without notice for enhancement
and quality improvement. Even when using the product continuously, be sure to read
the manual in the CONTEC's website and understand the contents.
When the product is used in a place that is affected by overcurrent or overvoltage
(lightning surge), select appropriate surge protection device for all of the route (Power
line, signal line, earth, etc.). Consult with the specialist regarding selecting, purchasing,
and setting the surge protection device.
When disposing of the product, follow the disposal procedures stipulated under the
relevant laws and municipal ordinances.
The ferrite core must be installed in interface connecting cable so that the product may
suit the above-mentioned standard.
Regardless of the foregoing statements, CONTEC is not liable for any damages
whatsoever (Including damages for loss of business profits) arising out of the use or
inability to use the CONTEC product or the information contained herein.
4. Names of Components
No.
N
ame
No.
N
ame
1
Power
LED
6
Bracket Screw Holes for DIN
-
rail
Installation
2
Power Failure Detection Relay
LED
7
Bracket Screw Holes for Wall Installation
(M3)
3
Link / Act LED
8
P
ower
Supply
Connector
:
PWR1, PWR2, Power Failure Detection
Relay
4
PoE LED
9
Power Failure Detection
DIP
Switch
5
LAN
P
ort
1
0
Screw Holes for Grounding Wire (M3)
Setting the Power Failure Detection DIP Switch
This product has two power inputs (PWR-1 and PWR-2).
Power output failure can be detected with the set of the DIP switch.
The relay terminal (pin-3 and pin-4) of the power connector is open in normal mode, but it
closes before the power is supplied or when the power output of the PWR-1 or PWR-2
drops.
DIP
-
1
DIP
-
2
D
escription
OFF
OFF
Relays are always
open when the product is used.
OFF
ON
The relay closes when the power failure of PWR
-
1 drops
below
7
V.
ON
OFF
The relay closes when the power failure of PWR
-
2 drops
below
7
V.
ON
ON
The relay closes when the power of PWR
-
1 or PWR
-
2 drops
below
7
V.
5. Specifications
Function Specifications
Item
Specifications
Ethernet standards
IEEE802.3/IEEE802.3u/IEEE802.3ab/IEEE802.3af/
IEEE802.3at*
–
compliant
Data transfer rate
10Mbps/100Mbps/1000Mbps (auto
-
negotiation)
Communications method
All ports: Full/Half duplex (auto
-
negotiation)
Flow control
Full Duplex : IEEE802.3x compliant flow control
Half Duplex :
Back pressure
Number of effective ports
8
Switching method
Store
and forward
Address table
4,096 entries
Jumbo
f
rame
9Kbyte
Buffer capacity
1
92K
byte
Aging time
300
秒
LED indicator
POWER
x 2
(Green),
PWR Failure(
Orange
)
,
LINK/ACT
x 8
(Green
/Orange
),
PoE
x
8
(
Green
)
D
IP
switch
Power failure detection
function switch for PWR
-
1 and PWR
-
2
Power supply voltage
12V
-
57VDC
±
5
％
FG pin
Power supply connector equipped with FG pin
Power consumption (Max.)
When PoE is not in use
:
12V 0.47A,
24V 0.24A,
57V 0.10A
When PoE is in use
:
12V
7.
5
6
A
,
24V
7
.22
A
,
57V
3
.04
A
Physical dimensions (mm)
41(W)×94.9(D)×144.3(H)
(
exclusive of protrusions
)
Weight
700g
Module installation method
Mounting on
DIN
rail or on the wall
*1 When the supplied voltage is 24VDC-57VDC: The maximum power by PoE is 120W in total for
all ports.
When the supplied voltage is less than 24VDC-57VDC: The maximum power by PoE is 60W in
total for all ports.
Installation Environment Requirements
Item
Specifications
Operating ambient temperature
-
35
-
+
70
°C
Operating
ambient humidity
5
-
9
5
%RH (No condensation)
Non
-
operating ambient temperature
-
38
-
+
70
°C
Non
-
operating ambient humidity
5
-
9
5
%RH (No condensation)
Floating dust particles
Not to be excessive
Corrosive gases
None
Line
-
Noise
resistance
Line
-
noise
AC line/2
K
V, Signal line/1
K
V (
EN
61000
-
4
-
4Level 3,
IEC
61000
-
4
-
4Level 3)
Static electricity
resistance
Contact discharge/4
K
V (
EN
61000
-
4
-
2Level 2,
IEC61000-4-2Level 2)
Atmospheric discharge/8KV (EN61000-4-2Level 3,
IEC
61000
-
4
-
2Level 3)
Vibration
resistance
Sweep resistance
10
-
57Hz/semi
-
amplitude 0.
075
mm,57
-
150Hz/9.8M/s
2
(1G),
40minutes each in X, Y, and Z directions
(JIS C60068
-
2
-
6
-
compliant, IEC60068
-
2
-
6
-
compliant)
Impact resistance
1
0
G, half
-
sine shock for 11ms in X, Y, and Z
directions
(JIS C60068-2-27-compliant, IEC60068-2-27-compli-
ant)
Grounding
Class D grounding
,
SG
-
FG/
non
-
conductive
Standard
VCCI Class A, FCC Cla
ss A,
CE Marking (EMC Directive Class A, R
oHS Directive)
6. Physical Dimensions
-
1
Contec SH-9008AT-POE Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Contec SH-9008AT-POE is an unmanaged Gigabit Ethernet Switch HUB with PoE function. It supports IEEE802.3/IEEE802.3u/IEEE802.3ab/IEEE802.3af/IEEE802.3at standards and offers data transfer rates of 10Mbps/100Mbps/1000Mbps. With its 8-port 10/100/1000 Base-T compatible HUB, it allows for seamless data transmission and network expansion. The device operates within a temperature range of -35 to +70°C, making it suitable for various environments.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Contec CPS-SSI-4P Owner's manual
-
Contec SH-9008AT-POE NEW Reference guide
-
-
-
Contec CPS-HBL-8005F Owner's manual
-
-
-
-
-
Other documents
-
ECD DIRECTCONNECT DCGP81000M User manual
-
Add-On Computer Peripherals (ACP) ADD-POEINJCT60W Datasheet
-
Cudy IG1005 Installation guide
-
Allnet ALL-SGI8205PD Quick start guide
-
Intercoax ECP-2704T Owner's manual
-
Digitus DN-651150 Quick start guide
-
Digitus DN-651132 Quick start guide
-
CTC Union IGS-800C-8PHE Quick Installation Manual
-
-
Molex 0022011032 Operating instructions
