Broadcom IBM Z and Brocade Qualification support for FOS 8.2.2c User guide

Brand: Broadcom

Model: IBM Z and Brocade Qualification support for FOS 8.2.2c

Type: User guide

Page 1 of 3

IBM Corporation

2455 South Road

Poughkeepsie, NY 12601

Broadcom Inc

1320 Ridder Park Drive

San Jose, CA 95131

August 4, 2020

IBM Z® and Brocade Qualification support for FOS 8.2.2c

International Business Machines Corporation and Brocade LLC have successfully completed qualification testing, of zHPF

(High

Performance FICON), FICON

and FCP protocols, using the switches and directors in Table 1 with FOS 8.2.2c in the configurations in

Table 2, for the following IBM Z family hardware platforms: IBM z15™ models T01 (z15 T01) and T02 (z15 T02)

, z14™ (z14) and IBM z14

Model ZR1 (z14 ZR1), IBM z13

(z13) and IBM z13s

(z13s), and for the following IBM LinuxONE™ platforms: LinuxOne III™ models LT1 and

LT2, LinuxOne Emperor II™, LinuxOne Emperor™, LinuxOne Rockhopper II™, and

LinuxOne

Rockhopper™.

Brocade Network Advisor 14.4.5 was used as the management tool during the qualification testing.

Supported Directors and Switches

Table 1 Supported directors and switches

Brocade

Name

IBM Name

IBM

Machine

Type

Max.

Logical

Switches

Max. CUP

Instances

FICON Base

Switch (XISL)

Support

Supported Blades

Supported SFP

Optics

X6-8 SAN512B-6 8961-F08

Yes

FC32-48, SX6,

FC32-64

10, 16, 32

Gbps,

16, 32

Gbps

QSFPs

ICL QSFPs

32 Gbps 2km ICL

QSFPs,

SmartOptics

16Gbps 40km

DWDM SFP+

X6-4 SAN256B-6 8961-F04

Yes

G620 SAN64B-6

8960-F64

8960-N64

N/A

10, 16, 32

Gbps,

SmartOptics

8510-8

SAN768B-2

2499-816

8 4 Yes

FC16-32,

FC16-48,

FC16-64

FC8-64

FX8-24E,

FX8-24

8, 10, 16 Gbps,

16 Gbps QSFPs

ICL QSFPs

SmartOptics

16Gbps 40km

DWDM SFP+

8510-4

SAN384B-2

2499-416

8 4 Yes

6510

SAN48B-5

2498-F48

4 2 No N/A 8, 10, 16 Gbps

7840 SAN42B-R 2498-R42

Yes

N/A

8, 10, 16, 40

Gbps

a. The Extended Long Wavelength (ELWL) optic versions for speeds up to 32 Gbps are also supported up to a distance of 25 km.

b. The FC32-64, FC16-64 and FC8-64 are supported for FCP use only, and are not supported in the same logical switch as FICON traffic.

c. 16Gbps QSFPs (both the 50m and 100m versions) are supported on both the FC16-64 blade and ICLs. 2km QSFPs are supported on ICL’s only.

d. 32 Gbps QSFPs can only connect to other 32 Gbps QSFPs.

e. The SmartOptics 16Gbps 40km DWDM SFP+ (P/N: 16G-ER-Dxxx-BR2) can be used in conjunction with the SmartOptics M-Series Intelligent Multiplexer (M-1601).

See Note 3 below.

f. Direct connections between IBM Z FICON adapters and Brocade 32 Gbps Optics were tested at speeds of 16Gbps and 8Gbps since there are currently no

32 Gbps IBM Z adapters. Links running at 32 Gbps links were only tested over ISLs and ICLs between Brocade Gen6 Directors/switches.

g. QSFPs in the G620 switch are only supported for QSFP connections to other G620 QSFPs, they cannot be used for ICL connections to Gen5 or Gen6 chassis.

Additional details on support

for

Brocade directors and switches connected

FICON

protocol-attached

IBM

released

after

z14 and z14 ZR1 can be found on the

Brocade Product End of Life

. Please contact your sales representative for additional details.

Page 2 of 3

Supported Topologies

Table 2 Supported cascaded

configurations

Switch(A) <ISL> Switch(A)

Extension(A) <IP> Extension (A)

Switch(A) <ISL> Extension (B) <IP> Extension (A)

Switch(A) <ISL> Extension (B) <IP> Extension (B) <ISL> Switch(A)

Switch(B) <ICL> Switch(B) <ISL> Extension (B) <IP> Extension (A)

Switch(B) <ICL> Switch(B) <ISL> Extension (B) <IP> Extension (B) <ISL> Switch(A)

Switch(B) <ICL> Switch(B) <ISL> Extension (B) <IP> Extension (B) <ISL> Switch(B) <ICL> Switch(B)

Switch(B) <ICL> Switch(B) <ISL> Switch(A)

Switch(B) <ICL> Switch(B) <ISL> Switch(B) <ICL> Switch(B)

Switch(C) <ICL> Switch(C) <ICL> Switch(C)

FICON Multihop Configurations for Gen5 and Gen6 Switches and Directors (see Note 4 below)

Restrictions and Switch

Descriptions:

Extension(A):

• Extension switch 7840 or 7800, or extension blade FX8-24E or FX8-24.

• Extension switch 7840 must only be connected to another 7840 or an SX6 extension blade for IP extension.

Extension(B):

• Extension switch 7840 or 7800, or extension blade FX8-24E or FX8-24.

• Extension switch 7840 must only be connected to another 7840 or an SX6 extension blade for IP extension.

• Switch & IP connections only. No device or channel connections.

Switch(A):

• May be any switch in

Table

Switch(B)

• May be X6-8 or X6-4

• May be 8510-8 or 8510-4

• May be DCX or DCX-4S

Switch(C):

• May be X6-8 or X6-4

• May be 8510-8 or 8510-4

a. This configuration is also supported as a triangle configuration. All Directors in a triangle configuration must be of the same family (all Gen5 or all Gen6).

b. ICL connections are fiber on Gen5 and Gen6 directors (X6-8, X6-4, 8510-8 and 8510-4) and therefore cannot be connected to Gen4 directors (DCX and DCX-4S)

which use copper ICLs.

FICON Release Notes

Although the distances for the protocols supported for these switches, FICON, FCP, FCIP, and ISLs, have been successfully

tested to a distance of 300km, IBM requires an Extended Distance RPQ for IBM Z and for LinuxOne to assure applications

greater than 100km adhere to the bounds of our qualification.

The new supported hardware features in this release are:

• 32 Gbps 25KM Extended Long Wavelength (ELWL) optic

The new supported features and functions in this release are:

• Fibre Channel Endpoint Security

The supported routing modes for FICON are:

• Exchanged Base Routing (EBR) with FICON Dynamic Routing (see Note 5 below)

• Device Base Routing (DBR)

• Port Based Routing (PBR)

Please refer to the Brocade Fabric OS v8.2.2c Release Notes v1.0 (or the latest available version) and see section

“Appendix: Additional Considerations for FICON Environments” for additional requirements, restrictions, and

recommendations.

Page 3 of 3

Notes and Recommendations:

1. The IBM Z and IBM LinuxOne supported FOS upgrade path to 8.2.2c for Gen5 and Gen6 is from 8.2.2a, 8.2.0a, 8.1.2a, or

8.1.0c.

2. The High Integrity Fabric feature is required for proper operation with FICON channels; therefore, it is recommended that

customers verify HIF is enabled upon upgrade to FOS 7.3.0b or higher. If HIF is not enabled, FICON channels will go into an

Invalid Attach state after a channel or port event occurs that requires the channels to log in.

3. Use of SmartOptics may require users to make changes to their MAPs policies. For details on the SmartOptics

implementation with Gen5 and Gen6 products Please refer to the FICON Appendix of the Brocade Fabric OS v8.2.0a Release

Notes v1.0 (or the latest available version).

4. For more information regarding use of FICON multihop, requirements and supported configurations, please refer to FICON

Multihop: Requirements and Configurations (WP102704) Whitepaper:

https://www-

03.ibm.com/support/techdocs/atsmastr.nsf/WebIndex/WP102704

5. For more information regarding host and control unit requirements for use of FICON Dynamic Routing, please refer to

“FICON Dynamic Routing (FIDR): Technology and Performance Implications (WP102651)” whitepaper:

http://www-

03.ibm.com/support/techdocs/atsmastr.nsf/WebIndex/WP102651

6. Brocade I/O Insight and Analytics Monitoring Platform (AMP) are supported in a Linux on z Systems environment. These

analytics capabilities are limited to FCP solutions only. Brocade AMP connectivity to an IBM Z FICON SAN Fabric is supported

for FCP solutions such as Linux for z Systems or IBM Metro Mirror.

7. For cabling and other best practices please visit IBM’s Cabling Considerations in Storage Area Networks support document:

http://www-01.ibm.com/support/docview.wss?uid=ssg1S1004299

Results achieved were in a test environment under laboratory conditions. IBM does not make any representations or

warranties regarding Brocade LLC products. Brocade retains sole responsibility for its products, the performance of such

products and all claims relating to such products, including without limitation its products’ compliance with product

specifications, industry standards and safety and other regulatory requirements.

If a device supports attachment to the IBM Z platform, then IBM anticipates it will operate properly with the qualified

products in this letter. For a list of IBM supported devices, please visit IBM System Storage Interoperation Center (SSIC):

http://www-

03.ibm.com/systems/support/storage/ssic/interoperability.wss.

For third party devices please check with the

OEM device vendor for support statements regarding attachment to IBM Z.

The terms zHPF, FICON, IBM, IBM Z, z15, z14, z Systems, z13, z13s, zEC12, zBC12, zEnterprise, LinuxOne, LinuxOne Emperor and

LinuxOne Rockhopper are trademarks or registered trademarks of International Business Machines Corporation.

Broadcom IBM Z and Brocade Qualification support for FOS 8.2.2c User guide

Broadcom IBM Z and Brocade Qualification support for FOS 8.2.2c User guide

Broadcom IBM Z and Brocade Qualification support for FOS 8.2.2c User guide

Related papers

Other documents