Sunell SN-IPP5790DDN User manual

Panoramic Security Surveillance

Network Camera

User Manual

Issue

V1.0

Date

2019-01-28

Panoramic Security Surveillance Network Camera

User Manual

Precautions

Issue V1.0 (2019-01-28）

i

Precautions

Fully understand this document before using this device, and strictly observe rules in

this document when using this device. If you install this device in public places,

provide the tip "You have entered the area of electronic surveillance" in an eye-

catching place. Failure to correctly use electrical products may cause fire and severe

injuries. To prevent accidents, carefully read the following context:

Symbols

This document may contain the following symbols whose meanings are described

accordingly.

Symbol

Description

It alerts you to fatal dangers which, if not avoided, may

cause deaths or severe injuries.

It alerts you to moderate dangers which, if not avoided,

may cause minor or moderate injuries.

It alerts you to risks. Neglect of these risks may cause

device damage, data loss, device performance

deterioration, or unpredictable results.

It provides a tip that may help you resolve problems or

save time.

It provides additional information.

To prevent electric shocks or other dangers, keep power plugs dry and clean.

 Strictly observe installation requirements when installing the device. The

manufacturer shall not be held responsible for device damage caused by users' non-

conformance to these requirements.

Precautions

Panoramic security surveillance Network Camera

User Manual

ii

Issue V1.0 (2019-01-28)

 Strictly conform to local electrical safety standards and use power adapters that are

marked with the LPS standard when installing and using this device. Otherwise,

this device may be damaged.

 Use accessories delivered with this device. The voltage must meet input voltage

requirements for this device.

 If this device is installed in places with unsteady voltage, ground this device to

discharge high energy such as electrical surges in order to prevent the power supply

from burning out.

 When this device is in use, ensure that no water or any liquid flows into the device.

If water or liquid unexpectedly flows into the device, immediately power off the

device and disconnect all cables (such as power cables and network cables) from

this device.

 Do not place Panoramic security surveillance network camera and unpackaged

products at a radiation source with a high intensity regardless of whether the device

is in the normal power-on state, for example, the sun, laser, and electric arc welder,

and place Panoramic security surveillance network camera and unpackaged

products against objects with a high heat source, for example, the sun. Otherwise,

the accuracy of Panoramic security surveillance network camera will be affected.

In addition, the detector in Panoramic security surveillance network camera may be

permanently damaged.

 If this device is installed in places where thunder and lightning frequently occur,

ground the device nearby to discharge high energy such as thunder strikes in order

to prevent device damage.

 During the outdoor installation, prevent the morning or evening sunlight incidence

to the lens of the camera. The sun shade must be installed and adjusted according to

the angle of the sunlight illumination.

 Avoid heavy loads, intensive shakes, and soaking to prevent damages during

transportation and storage. The warranty does not cover any device damage that is

caused during secondary packaging and transportation after the original packaging

is taken apart.

 This device is a static sensitivity device. Improper static may damage the camera.

ESD protection measures and reliable grounding must be well prepared for device

installation and uninstallation.

 Protect this device from fall-down and intensive strikes, keep the device away from

magnetic field interference, and do not install the device in places with shaking

surfaces or under shocks.

 Use a soft and dry cloth to clean the device body. In case that the dirt is hard to

remove, use a dry cloth dipped in a small amount of mild detergent and gently wipe

the device, and then dry it again. Pay special attention to the front window of

camera because this is precision optics. If the front window has water spots, use a

clean and soft cloth to moisten with water and wipe it. If the front window needs

Panoramic Security Surveillance Network Camera

User Manual

Precautions

Issue V1.0 (2019-01-28）

iii

further cleaning, use a soft cloth dampened with isopropyl alcohol or detergent.

Improper cleaning can cause damage to the device.

 Do not jam the ventilation opening. Follow the installation instructions provided in

this document when installing the device.

 Keep the device away from heat sources such as radiators, electric heaters, or other

heat equipment.

 Keep the device away from moist, dusty, extremely hot or cold places, or places

with strong electric radiation.

 If the device is installed outdoors, take insect- and moisture-proof measures to

avoid circuit board corrosion that can affect monitoring.

 Remove the power plug if the device is idle for a long time.

 Before unpacking, check whether the fragile sticker is damaged. If the fragile

sticker is damaged, contact customer services or sales personnel. The manufacturer

shall not be held responsible for any artificial damage of the fragile sticker.

Special Announcement

All complete products sold by the manufacturer are delivered along with nameplates,

operation instructions, and accessories after strict inspection. The manufacturer shall

not be held responsible for counterfeit products.

This manual may contain misprints, technology information that is not accurate enough,

or product function and operation description that is slightly inconsistent with the

actual product. The manufacturer will update this manual according to product function

enhancement or changes and regularly update the software and hardware described in

this manual. Update information will be added to new versions of this manual without

prior notice.

This manual is only for reference and does not ensure that the information is totally

consistent with the actual product. For consistency, see the actual product.

Contents

Panoramic security surveillance Network Camera

User Manual

iv

Issue V1.0 (2019-01-28)

Contents

1 Product Overview .................................................................................................... 6

1.1 Description of Product.................................................................................................... 6

1.2 Device Structure ............................................................................................................. 6

1.3 Cable Connection ........................................................................................................... 7

2 Installation ................................................................................................................ 9

2.1 Preparations .................................................................................................................... 9

2.2 Installation Mode............................................................................................................ 9

2.3 Installation Procedure ..................................................................................................... 9

3 Quick Configuration ............................................................................................. 15

3.1 Login and Logout ......................................................................................................... 15

3.2 Main Page layout .......................................................................................................... 16

3.3 Change the Password.................................................................................................... 18

3.4 Browse Video ............................................................................................................... 19

3.4.1 Install Plugins ................................................................................................... 21

3.5 Setting Local Network Parameters ............................................................................... 21

4 Parameter Setting ................................................................................................... 24

4.1 Sensor Setting Interface ................................................................................................ 24

4.2 Time Segment ............................................................................................................... 25

4.3 Image Setting ............................................................................................................... 25

4.4 Scene ............................................................................................................................ 27

4.5 Exposure ....................................................................................................................... 27

4.6 White Balance .............................................................................................................. 29

4.7 DayNight ...................................................................................................................... 30

4.8 Noise Reduction ........................................................................................................... 31

4.9 Enhance Image ............................................................................................................. 32

5 Configuration ......................................................................................................... 35

5.1 Device Information ...................................................................................................... 35

5.2 Stream .......................................................................................................................... 36

5.3 Device .......................................................................................................................... 40

5.4 Intelligent Analysis ....................................................................................................... 41

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

v

5.5 Alarm ............................................................................................................................ 41

5.6 Device Record .............................................................................................................. 42

5.7 Privacy Masking ........................................................................................................... 43

5.8 Network Service ........................................................................................................... 44

5.9 Privilege Manager ........................................................................................................ 44

5.10 Protocol ...................................................................................................................... 45

5.11 Device Log ................................................................................................................. 46

5.12 Maintenance ............................................................................................................... 46

5.13 Local Config ............................................................................................................... 47

6 Technical Specifications ....................................................................................... 48

Contents

Panoramic security surveillance Network Camera

User Manual

6

Issue V1.0(2019-01-28)

1 Product Overview

1.1 Description of Product

Panoramic security surveillance network camera provides 360°* 360°panoramic

views without blind spots, making it ideal for wide and open areas, such as airport,

shopping malls, banks, hotels, stores, square and more. The camera is 8MP single pixel,

and 32MP four eyes.

1.2 Device Structure

Figure 1-1 shows the rear panel of the Panoramic Security Surveillance Network Camera. For details

about the interfaces, see Table 1-1.

Figure 1-1 Appearance and interfaces of device

90

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

7

112.2

101.8

31

39.4

31

39.4

31

39.4

31 39.4

4-M8 * 6mm

Table 1-1 Interfaces

1.3 Cable Connection

Figure 1-2 the multi-connector combination cable of the network camera. For details

about the multi-connector combination cable, see Table 1-2.

Figure 1-2 Multi-connector combination cable

Contents

Panoramic security surveillance Network Camera

User Manual

8

Issue V1.0(2019-01-28)

Table 1-2 Multi-connector combination cable

NO.

Color

Port

Description

1

N/A

Network

access port

Connects to a standard Ethernet cable.

2

Power supply

port

Connects to a 12V direct current (DC)

power supply.

3

Audio input

port

Receives analog audio signals from

devices such as a sound pickup device.

4

Audio output

port

Connects to an external audio device

such as a speaker.

5

Gray core

Alarm output

terminal A

(normal open)

Alarm output

Purple core

Alarm output

terminal B

(normal open)

yellow core

Alarm input

positive

terminal

Alarm input terminal

Orange core

Alarm input

ground

terminal

1.4 Configuration Requirements

CPU: Intel(R) Core(TM) i7-8700 cpu @3.20GHz or later

RAM:16GB or more

Graphics card：GeForce GTX 1070 Ti or above。

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

9

2 Installation

2.1 Preparations

User need the tools and accessories shown in Table 2-1 during the installation (you

need to prepare the tools by yourself, and the accessories are in the package of the

camera).

Table 2-1 Installation tools

Tools

Appearance

L-Wrench (delivered with the camera)

Hexagon socket stainless steel

screw(delivered with the camera)

2.2 Installation Mode

If the camera is installed indoor, a bracket should be selected; if the camera is installed

outdoor, the shield and upright column should be selected.

NOTE

The bracket where the support is mounted must be able to withstand at least three times of

the total weight of the support and the camera.

2.3 Installation Procedure

Step 1 Remove the installation block delivered with the camera. Fix the installation block on

the top or on the bottom of the camera, as shown in Figure 2-1.

Contents

Panoramic security surveillance Network Camera

User Manual

10

Issue V1.0(2019-01-28)

Figure 2-1 Fix the installation block

Figure 2-2 Dimension of bracket

91

41

φ47

Step 2 Fix the mounting bracket on the pole, as shown in Figure 2-3.

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

11

Figure 2-3 Fix the mounting bracket

Step 3 ( Install with Column ) Align the camera adapter with the adapter hole on the column,

and when it is in place, fix the two with screws and confirm that fixing screw is fixed

in the groove of the adapter, as shown in Figure 2-4.

Contents

Panoramic security surveillance Network Camera

User Manual

12

Issue V1.0(2019-01-28)

Figure 2-4 Install with column

Groove

Step 4 ( Install on ceiling ) Fix the mounting bracket on the pole, as shown in Figure 2-5.

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

13

Figure 2-5 Fix the mounting bracket

Step 5 ( Install on ceiling ) Align the camera adapter with the adapter hole on the column, and

when it is in place, fix the two with screws and confirm that fixing screw is fixed in the

groove of the adapter, as shown in Figure 2-4.

Contents

Panoramic security surveillance Network Camera

User Manual

14

Issue V1.0(2019-01-28)

Figure 2-6 Install in ceiling

Groove

----End

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

15

3 Quick Configuration

3.1 Login and Logout

You must use Internet Explorer 8 or a later version to access the web management

system; otherwise, some functions may be unavailable.

Login system

Step 1 Open the Internet Explorer, enter the IP address of IP camera (default value:

192.168.0.120) in the address box, and press Enter.

The login page is displayed, as shown in Figure 3-1.

Figure 3-1 Login page

Step 2 Input the User and password.

 The default name and password are both admin. Modify the password when you login

the system for first time to ensure system security. After modifying password, you need

to wait at least three minutes then power off to make sure modifying successfully . Or

login the Web again to test the new password.

 You can change the system display language on the login page.

Step 3 Click Login button. The main page is displayed.

----End

Contents

Panoramic security surveillance Network Camera

User Manual

16

Issue V1.0(2019-01-28)

logout

To logout of system, click in the upper right corner of the main page, the login

page is displayed after you log out of the system.

3.2 Main Page layout

On the main page, you can view real-time video, set parameter, Video parameter, Video

control, and logout of the system. Figure 3-2 is shown the main page layout. Table 3-1

lists the elements on the main page layout.

Figure 3-2 Main page layout

1234 5

67 8 9 10 11 12 13 14 15

Table 3-1 Elements on the main page

No.

Element

Description

1

Real-time video

area

Real-time videos are played in this area. User can also set

sensor parameters.

2

Playback

User can query the playback videos in this area.

NOTE

Panoramic Security Surveillance Network Camera

User Manual

Contents

Issue V1.0 (2019-01-28）

17

No.

Element

Description

Only when the SD card or NAS have videos that user can query

the playback videos.

3

Device

configuration

You can choose a menu to set device parameters,

including the device information, audio and video streams,

alarm setting, and privacy mask function.

4

Change

password

You can click to change the password.

5

Sign Out

You can click to return to the login page.

6

Stream

There are four streams. Choose one type from drop-down

list. Stream 4 is SVC stream.

7

Pause/Start

Close live video or play live video.

8

Live/Smooth

Switch image quality.

9

Audio

Open or close audio.

10

Interphone

Open or close interphone.

11

Sensor setting

Click the icon, it will access to sensor setting.

12

Snapshot

Click the icon, it will snapshot.

13

Local record

Click the icon, it will record video and save to local folder.

14

Mode

: Panoramic mode, fisheye

mode, crystal ball mode, prospective mode, planet mode, as shown in

figure 3-3 to figure 3-6.

15

Intelligent

analysis

Open or close intelligent analysis.

When the live video is full screen, user can use keyboard shortcuts to switch mode, F2

is for panoramic mode, F3 is for prospective mode, F4 is for crystal ball mode, F5 is

for fisheye mode, and F6for is planet mode.

The key A is for autorotation (tour)，the key S is for stopping spinning.

1. When the device generates an alarm, the alarm icon is displayed. You can click

to view the alarm information. When the device accepts an alarm signal, the alarm icon will

display within 10s in the web management system.

2. When the device encounters an exception, the fault icon is displayed. You can click

to view the fault information.

Contents

Panoramic security surveillance Network Camera

User Manual

18

Issue V1.0(2019-01-28)

Figure 3-3 Prospective mode

Figure 3-4 Crystal ball mode

Figure 3-5 Fisheye mode

Figure 3-6 Planet mode

----End

3.3 Change the Password

Description

User can click to change the password for logging to the system.

Page is loading ...

Sunell SN-IPP5790DDN User manual

Sunell SN-IPP5790DDN User manual

Other documents