Jaycar Electronics QC3602 Operation Handbook

VIDEO DOORPHONE

MODEL NO: QC3602

OPERATION HANDBOOK

……………………………… ……………………………………..

Ⅰ Important Safeguards

& Symbols explanation

Ⅱ Brief Introduction

Ⅲ Components

Ⅳ Wiring Diagram

Ⅴ Operation

Ⅵ Installation

Ⅶ Notice

Ⅷ Main Technical Features

Ⅸ Standard Accessories

Ⅰ Important Safeguards

& Symbols Explanation

Read instruction

.indoor use only Double insulation

CAUTION！

NON-PROFESSIONAL PERSON PLEASE

DO NOT OPEN IT

CAUTION!

1. THE VOLTAGE PARAMETER IS SHOWED ON

ADAPTOR.

2. WHEN THE PRODUCTS IS PLUG ON, MAKE

SURE THAT NO COVER ON THE SURFACE.

3. TO PREVENT FIRE, HIGH-HUMIDITY AND

DIRECTLY SUNSHINE.

4. THE APPARATUS SHALL NOT TO BE EXPOSED

DRIPPING OR SPLASHING.

The lightning flash

with the arrowhead

symbol, within an

equilateral triangle is

intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product’s

enclosure that may be of sufficient

magnitude to constitute a risk of

electrical shock to persons.

The exclamation point

within an equilateral

triangle is intended to

alert the user to keep

the important operating and

maintenance (servicing) instruction

accompanying the appliance.

Ⅱ Brief Introduction

Model QC3602 B/W Video Intercom Doorbell is an up-dated

designed small-sized multi-function product series by our company.

The product adopts closed circuit television monitoring principle,

CMOS camera shooting outdoor and display indoor, bi-directional

talkback, open the door lock indoor, accompanied with monitoring

outdoor situation as well as alarming. In nights cameras shooting with

infrared assisting, for all-weather using, with clear picture, attractive

appearance, practical and reliable, easy installation, convenient in using, it

can be widely used in various entrance guard burglar-proof monitoring

systems, it is the most ideal equipment for modern families, entrance

guard.

Please spend a little time to read this manual and you will know well

the operation and adjustment of this device, and enable to make good use

of it.

Welcome to use this Model QC3602 Video Intercom Doorbell, and we

believe that this device will contribute to the security of your family.

Ⅲ Components

A. Indoor Section (Refer to Fig.1)

1. Terminal of Video input

2. Terminal of GND

3. Terminal of DC12V power output

4. Terminal of Audio

5. Electrical Lock (A)

6. Electrical Lock (B)

7. Terminal of DC power input (-)

8. Terminal of DC power input (+) (Back)

9. N.C.

10. Display Screen

11. Power Indication

12. Monitor Button

13. Alarm

14. Unlocking Button

15. Handphone Switch

16. Contrast Adjustment

17. Volume Adjustment

18. Speaker

19. Handphone (Front) (Fig .1)

B. Outdoor Section (Refer to Fig.2)

1. Video output

2. GND

3. DC12V power input

4. Audio

5. Camera

6. Night Vision Illumination Source

7. Bell Button

8. Microphone

9. Speaker

Front Back

(Fig.2)

1256

789

10

11

12

13

14

15

16

17

18

19

12 3 4AB

97

8

5

6

Ⅳ Wiring Diagram

Function of Terminals:

NO Name Suggested Line Color Remark

1 VIDEO Yellow

2 GND Black (Blue)

3 12V POWER Red

4 AUDIO Green

5 LOCK（A）

6 LOCK（B）

7 DC Input(-)

8 DC Input(+)

El ectri cal Lock

A

B

AC 220V/50Hz

(DC+18V)

Back of Moni tor

Back of Camera

12

3

4 A B

+

-

(110V/60Hz)

9

Ⅴ Operation

1. When visitors press the chime button:

a. The monitor will chime and the visitors will be displayed on the screen.

b. You can pick up the handset and talk to the visitors.

c. You can view visitors without picking up the handset, or view camera images at

any time without visitors being aware they are being observed.

2. The monitor will chime and display the image, if the handset is not picked up

within 30 seconds the system will shutdown. After picking up the handset a 2 way

conversation may be conducted for two minutes, and if an optional door latch is

installed the door can be opened by pressing the door latch button.

3 Pressing the monitor button at any time will show the cameras image for 10

seconds.

4. The chime sound volume and contrast controls are situated under the handset.

5. The user can connect a electrical lock between monitor connector No.5 & No.6

as showed on the wiring diagram. The drive voltage for door-open from the monitor

is 12V, when the user select the electrical lock, please make sure the resistor of the

lock is not less than 15Ω, that means before install the lock if you use a voltage meter

to measure the resistor between point A and B (as showed in the wiring diagram),

there must be at least 15Ω resistor in the lock, otherwise, it may cause the picture

unstable trembling and damage the adaptor.

6. Due to the camera unit being equipped with infrared illumination, visitors can be

displayed on the monitor in weak lighting night, but due to CMOS camera’s own

feature, you can not see very clear picture in the very poor light condition.

Ⅵ Installation

1. Installation of the Monitor Unit

(1) Please ensure the unit is placed where it is easy to see and easy to operate, do not

expose the monitor screen directly to strong light, sunlight etc.

(2) With expansion tubes and screws, fix the mounting plate to the wall at a height

of between 1.5-1.7m from the floor. Wire up the monitor and fix to mounting

bracket. Refer to Fig.3:

1. Mounting place for indoor section

2. Iron Bracket for Hanging the unit

3. Fixing screw Holes

2. Installation of Camera Unit (Fig.4)

(1) Fix the outdoor section in the protective situation, where it is not exposed

to rain, moisture and direct sunlight.

(2) Recommended height of installation is approx 1.5-1.7m from the ground.

(confirm suitable mounting height prior to permanent installation)

(3) Use screws provided to fix the mounting frame to the wall, screw the metal

camera bracket to the mounting frame, connecting wires as per the wiring

diagram , then fix camera to the frame by screw at the bottom of the camera

(4) Ensure wiring on indoor and outdoor units match wiring diagram before

carrying out trial operation.

1. Camera mounting frame.

2. Assembly screw thread.

3. Mounting hole (4 pcs)

4. Hole for assembly screw.

5. Camera assembly screw

Fig.4

Fig.3

1

2

3

Input

24

5

1

2

3

Ⅶ Notice

1. To prevent electronic shock, the top cover should not be removed without

instructions of trained staff, please contact our company or our dealers.

2. The equipment should be placed properly and stably at ventilated location, to

prevent damp, dust and direct sunlight.

3. Chemicals are prohibited when the equipment is dirtied by dust, using soft, clean

and dry cloth is preferred.

Ⅷ Main Technical Features

1. Input Signal: Standard video signal, VS 1.0Vp-p

2. Input Impedance：75Ω

3. Luminance Appraisal Grade :> Grade 7

4. Picture Resolution: Monitor≥420TV Lines

Camera≥330 TV Lines

5. Time-dwell for Automatic Display:

a. Calling only: 30 seconds

b. Pressing Monitoring Button only: 10 seconds

c. Picking up the hand phone to talk: 2 minutes

d. Press alarm key: 10 seconds

6. Illumination Source for Night Vision: Infrared LED

7. Camera lens Angle: 65°diagonal (approx)

8. Voltage of Power: AC240V50Hz

9. Power Consumption: Stand-by: 2W；Operation:15W

10. Dimension of Indoor Section：222（W）×186（D）×55（H）（㎜）

11. Weight：2.4 ㎏ (one set)

Ⅸ Standard Accessories

Cable for Connecting Indoor and Outdoor sections:1 □

Fitting and Screws for Outdoor Section □

Fittings and Screws for Indoor Section □

User’s Manual:1 □

DC power:1 □

Jaycar Electronics QC3602 Operation Handbook

Jaycar Electronics QC3602 Operation Handbook

Other documents