OmniSistem Spark 7 Zoom User manual

Brand: OmniSistem

Model: Spark 7 Zoom

Category: Stroboscopes & disco lights

Type: User manual





Tel: 253-395-9500 Fax: 253-395-9494

6403 South 208th Street, Kent, WA 98032



KEEPTHISMANUALFORFUTURENEEDS 



1 of 25

Everypersoninvolvedwiththeinstallation,operationandmaintenanceofthisdeviceneedsto



● bequalified

● followtheinstructionsofthismanual

● considerthismanualtobepartofthetotalproduct

● keepthismanualfortheentireservicelifeoftheproduct



Passthismanualontoeveryfurtherowneroruseroftheproduct.

DownloadthelatestversionoftheusermanualfromtheOmniSistemwebsite.



Foryourownsafety,pleasereadthisusermanualcarefullybeforeyouinitiallystarttheproduct.



INTRODUCTION

Thank you for choosing an OmniSistem product. OmniSistem is a wholesaler of a large variety of lighting, sound,                 

truss, and effects. Since 1986, we have been providing quality and affordable lighting products to North America.                

Weareconfidentthatourexcellentproductswillmeetyourexpectations.



Includedinthisboxyouwillfind:



1. Spark7Zoom

2. UserManual

3. OmegaHolderwithQuickLockFastener

4. PowerSupplyCable

5. SafetyCable



SAFETYINSTRUCTIONS



This device left our facility after a thorough QC check. In order to maintain excellent condition and to ensure a safe                    

operation, it is absolutely necessary for the user to follow the safety instructions and warnings detailed in this user                  

manual.



Important:

Damagescausedbythedisregardofthisusermanualarenotsubjecttowarranty.Thedealer

willnotacceptliabilityforanyresultingdefectsorproblems.



2 of 25

(SafetyInstructionsContinued)

● If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch               

it on immediately. The arising condensation water might damage your device. Leave the device switched              

offuntilithasreachedroomtemperature.



● Please make sure that there are no obvious transport damages. Should you notice any damages on the                

A/C connection cable or on the casing, do not take the device into operation and immediately consult                

yourlocaldealer.



● This device falls under Protection Class I. The power plug must only be plugged into a Protection Class I                  

outlet. The voltage and frequency must exactly be the same as stated on the device. Wrong voltages or                 

poweroutletscanleadtothedestructionofthedeviceandmortalelectricalshock.



● Always plug in the power plug last. The power plug must always be inserted without excessive force.                

Makesurethattheplugistightlyconnectedwiththeoutlet.



● Never let the power cord come into contact with other cables! Handle the power cord and all connections                 

with the mains with caution! Never touch them with wet hands, as this could lead to mortal electrical                 

shock.



● Never modify, bend, strain mechanically, put pressure on, pull or heat up the power cord. Never operate                

next to sources of heat or cold. Disregarding this can lead to power cord damages, fire or mortal electrical                  

shock.



● The cable insert or the female part in the device must never be strained. There must always be sufficient                  

cabletothedevice.Otherwise,thecablemaybedamagedwhichmayleadtomortaldamage.



● Make sure that the power cord is never crimped or damaged by sharp edges. Check the device and the                  

powercordfromtimetotime.



● If extension cords are used, make sure that the core diameter is sufficient for the required power                

consumption of the device. All warnings concerning the power cords are also valid for possible extension               

cords.



● Always disconnect from the power source, when the device is not in use or before cleaning it. Only handle                  

the power cord by the plug. Never pull out the plug by tugging the power cord. Otherwise, the cable or                   

plug can be damaged leading to mortal electrical shock. If the power plug or the power switch is not                  

accessible,thedevicemustbedisconnectedviathemains.



● If the power plug or the device is dusty, the device must be taken out of operation, disconnected and then                   

be cleaned with a dry cloth. Dust can reduce the insulation which may lead to electrical shock. More                 

severedirtinandatthedeviceshouldonlyberemovedbyaspecialist.



● There must never enter any liquid into power outlets, extension cords or any holes in the housing of the                  

device. If you believe even a minimal amount of liquid may have entered the device, it must immediately be                  

disconnected. This is also valid, if the device was exposed to high humidity. Also if the device is still                  

running, the device must be checked by a specialist if the liquid has reduced any insulation. Reduced                

insulationcancausemortalelectricalshock.



● There must never be any objects entering into the device. This is especially valid for metal parts. If any                  

metal parts like staples or coarse metal chips enter into the device, the device must be taken out of                  

operation and disconnected immediately. Malfunction or shortcircuits caused by metal parts may cause            

mortalinjuries.

Keep away children and amateurs! Never leave this device running unattended.

3 of 25

OPERATINGPROCEDURES

Thisdeviceisamovingheadlightforcreatingdecorativeeffects.Thisproductisonlyallowedtobeoperatedwith

analternatingvoltageof100240V,50/60Hzandwasdesignedforindooruseonly.



Thisdeviceisdesignedforprofessionaluse,e.g.onstages,inclubs,bars,theatres,etc.



Lightingeffectsarenotdesignedforpermanentoperation.Consistentoperationbreakswillensurethatthedevice

willserveyouforalongtimewithoutdefects.



Donotshakethedevice.Avoidbruteforcewheninstallingoroperatingthedevice.



Neverliftthefixturebyholdingitattheprojectorhead,asthemechanicsmaybedamaged.Alwaysholdthe

fixtureatthetransporthandles.



Whenchoosingtheinstallationspot,pleasemakesurethatthedeviceisnotexposedtoextremeheat,moisture

ordust.Thereshouldnotbeanycableslyingaround.Pleasemakesurethattheunitcannotbetouchedor

bumped.



Thisdevicemustneverbeoperatedorstockpiledinsurroundingswherewatersplash,rain,moistureorfogmay

harmthedevice.Moistureorveryhighhumiditycanreducetheinsulationandleadtomortalelectricalshocks.

Whenusingsmokemachines,makesurethatthedeviceisneverexposedtothedirectsmokejetandisinstalled

inadistanceof0.5metersbetweensmokemachineanddevice.Theroommustonlybesaturatedwithanamount

ofsmokethatthevisibilitywillalwaysbemorethan10meters.



Theambienttemperaturemustalwaysbebetween15°Cand+45°C.Keepawayfromdirectheat(particularlyin

cars)andheaters.



Therelativehumiditymustnotexceed50%withanambienttemperatureof45°C.This

devicemustonlybeoperatedinanaltitudebetween20and2000moversealevel.



Neverusethedeviceduringthunderstorms.Overvoltagecoulddestroythedevice.Alwaysdisconnectthedevice

duringthunderstorms.



Thissymboldeterminestheminimumdistancefromlightedobjects.Theminimumdistance

betweenlightoutputandtheilluminatedsurfacemustbemorethanthisvalue.



Thedevicemustonlybeinstalledonanonflammablesurface.Inordertosafeguardsufficientventilation,leave

50cmoffreespacearoundthedevice.



Thehousingmustnevertouchsurroundingsurfacesorobjects.



Makesurethattheareabelowtheinstallationplaceisclearwhenrigging,deriggingorservicingthefixture.



Foroverheaduse(mountingheight>100cm),alwaysfixthefixturewithanappropriatesafetycable.Fixthesafety

cableatthecorrectfixationpointsonly.Thesafetycablemustneverbefixedatthetransporthandles!



Onlyoperatethefixtureafterhavingcheckedthatthehousingisfirmlyclosedandallscrewsaretightlyfastened.



ThemaximumambienttemperatureTa=45°Cmustneverbeexceeded.



Operatethedeviceonlyafterhavingbecomefamiliarizedwithitsfunctions.Donotpermitoperationbypersonsnot

qualifiedforoperatingthedevice.Mostdamagesaretheresultofunprofessionaloperation!



Pleaseusetheoriginalpackagingifthedeviceistobetransported.

Pleaseconsiderthatunauthorizedmodificationsonthedeviceareforbiddenduetosafetyreasonsand

willvoidyourwarranty.



Neverremovetheserialbarcodefromthedeviceasthiswouldvoidthewarranty.

Ifthisdevicewillbeoperatedinanywaydifferenttotheonedescribedinthismanual,theproductmaysuffer

damagesandtheguaranteebecomesvoid.Furthermore,anyotheroperationmayleadtodangerslikeshort

circuit,burns,electricshock,crashing,etc.

4 of 25

PRODUCTFEATURES&SPECIFICATIONS



Light

● Lightsource:7xOSRAM15W4in1RGBWLEDs

● Lamplife:60,000hours

● LuminousFlux:3200lumen,6000lux@2.5m

● Control:Remoteon/offviaDMX

● Ballast:switchingmodepowersupply

● Beamangle:10°to60°



X/Y

● Pan:630°(2.5sec)or540°(2sec),Tilt:265°(1.8sec)

● 16bitresolution

● Autorepositioning

● 3phasemotorforfastandquietmovement



Features

● DMXchannels:15/24/14/16

● Fast,smooth,andsilentmovement

● RGBWColorMixing

● Zoom10°to60°

● Fullrange0100%dimmer

● Variousstrobe

● RDMfunctiontochangeDMXaddress,displayflip,X/YReverseandmore

● SoftwareupgradeviaDMX

● HibernationwhenlostDMXforpresettime

● Indicatetemperatureinfoofbase,armandlamp

● Fanspeedautochangeaccordingtotemperature

● Heatpipeforcooling



Display

● 2.4”LCDdisplaywithEnglish/Chinese/French/Spanishmenu

● Autolock

● Flip

● BackupcommunicatingIC



Power

● Maxpowerconsumption:115W

● Powersupply:Electronicautoranging

● Inputvoltagerange:100–240V,5060Hz



DimensionandWeight

● FixtureDimensions:244x179x322mm(9.6”x7”x12.7”)

● NetWeight:6kg(13.2lbs.)



5 of 25

OVERVIEW



(1) Head

(2) LED

(3) Arm

(4) Base

(5)Wirelessindicator

(6) Display

(7) Microphone

(8) Leftbutton

(9) Downbutton

(10) Enterbutton

(11) Upbutton

(12) Rightbutton



(13) Fuseholder

(14) Powerinput

(15) Powerswitch

(16) Poweroutput

(17) 3PINDMXinputsocket

(18) 3PINDMXoutputsocket

 

6 of 25

INSTALLATION



Rigging



The installation of the projector has to be built and constructed in a way that it can hold 10 times the weight for 1                       

hourwithoutanyharmingdeformation.



The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This                

secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main                    

attachmentfails.



When rigging, derigging or servicing the fixture staying in the area below the installation place, on bridges, under                 

highworkingplacesandotherendangeredareasisforbidden.



The operator needs to make sure that safetyrelated and machine technical installations are approved by an expert                

beforetakingintooperationforthefirsttimeandafterchangesbeforetakingintooperationanothertime.



The operator needs to make sure that safetyrelated and machine technical installations are approved by an expert                

aftereveryfouryearsinthecourseofanacceptancetest.



The operator needs to make sure that safetyrelated and machine technical installations are approved by a skilled                

persononceayear.



Procedure:

Theprojectorshouldbeinstalledoutsideareaswherepersonsmaywalkbyorbeseated.



IMPORTANT! OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, including (but not limited to)          

calculating working load limits, installation material being used, and periodic safety inspection of all installation              

material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use                 

aprofessionalstructuralrigger.Improperinstallationcanresultinbodilyinjuryand/ordamagetoproperty.



Theprojectorneedstobeinstalledoutofreachofpeople.



If the projector shall be lowered from the ceiling or high joists, professional trussing systems need to be used. The                   

projectormustneverbefixedswingingfreelyintheroom.



Caution: Projectors may cause severe injuries when crashing down! If you have doubts concerning the safety of a                

possibleinstallation,doNOTinstalltheprojector!



Before rigging make sure that the installation area can hold a minimum point load of 10 times the projector's                  

weight.

7 of 25



Theunitcanbeplaceddirectlyonthestagefloororriggedinanyorientationonatrusswithoutalteringits

operationcharacteristics(seethedrawing).



Thefixturebaseenablesmountingintwo

ways.



Foroverheaduse(mountingheight

>100cm),alwaysinstallanappropriate

safetybond.



Pleasenote:foroverheadriggingin

publicorindustrialareas,aseriesof

safetyinstructionsinthismanualneed

tobefollowed.Theoperatormustinform

themselvesonthecurrentsafety

instructionsandconsiderthem.



Themanufacturercannotbemadeliablefordamagescausedbyincorrectinstallationsorinsufficientsafety

precautions!



Installthesafetybondbyinsertingthequicklinkintheholeonthebottomofthebase.Pullthesafetybondover

thetrussingsystem.Inserttheendinthequicklinkandtightenthefixationscrew.



Themaximumdropdistancemustneverexceed20cm.



Asafetybondwhichalreadyholdsthestrainofafallorwhichisdefectivemustnotbeusedagain.



8 of 25



1. OmegaHolder

2. Clamp

3. SafetyCable

4. QuickLockFastener



ScrewtheclampviaaM12

screwandnutontotheOmega

holder.



Insertthequicklockfasteners

oftheOmegaholderintothe

respectiveholesonthebottom

ofthedevice.Tightenthe

quicklockfastenersfully

clockwise.



 

9 of 25



DMX512connection/connectionbetweenfixtures



Pleasenote,thestartingaddressdependsuponwhichcontrollerisbeingused.



OnlyuseaDMXcableand3pinXLRplugsandconnectorsinordertoconnectthecontrollerwiththefixtureor

onefixturewithanother.



OccupationoftheXLRconnection:



If you are using controllers during your show, you can connect the DMX output of the controller directly with the                   

DMX input of the first fixture in the DMX chain. If you wish to connect DMX controllers with other XLR outputs,                    

youneedtouseadaptercables.



BuildingaserialDMXchain:

Connect the DMX output of the first fixture in the DMX chain with the DMX input of the next fixture. Always                    

connectoneoutputwiththeinputofthenextfixtureuntilallfixturesareconnected.



Caution: At the last fixture, the DMX cable needs to be terminated. Plug the terminator with a 120Ωresistor                

betweenSignal(–)andSignal(+)intheDMXoutputofthelastfixture.



10 of 25

ConnectionwiththeMains

Connectthedevicetothepowersourcewiththeenclosedpowersupplycable.



Theconfigurationoftheconnectioncablesisasfollows:



Cable

Pin

International

Brown

Live

L

Blue

Neutral

N

Yellow/Green

Ground



Groundneedstobeconnected!



Ifthedevicewillbedirectlyconnectedwiththelocalpowersupplynetwork,adisconnectionswitchwitha

minimumopeningof3mmateverypolehastobeincludedinthepermanentelectricalinstallation.



The device must only be connected with an electric installation carried out in compliance with the IEC standards.                 

The electric installation must be equipped with a Residual Current Device (RCD) with a maximum fault current of                 

30mA.



Devicemustnotbeconnectedtodimmingpacks.



The device is equipped with a lockable power input connector. Plug in the power cord and turn it to the right until it                      

locks.Plugthepowercordintoagroundedelectricaloutletthatmatchestheratedvoltageofthemachine.



OPERATION

Withthepowerswitch,youcanswitchthedeviceonandoff.

Afterbeingconnectedtothepowersupply,thefixturestartsrunning.Duringthereset,themotorsaretrimmedand

thedeviceisreadyforuse.



StandAloneoperation

IntheStandAlonemode,thedevicecanbeusedwithoutcontroller.



Disconnectthefixturefromthecontrollerandcalltheinternalprogram.

PleaserefertotheinstructionsunderControlBoard.



DMXControlledoperation

YoucancontroltheprojectorsindividuallyviayourDMXcontroller.EveryDMXchannelhasadifferentoccupation

withdifferentfeatures.TheindividualchannelsandtheirfeaturesarelistedunderDMXprotocol.



Addressing

TheControlBoardallowsyoutoassigntheDMXstartingaddress,whichisdefinedasthefirstchannelfromwhich

thefixturewillrespondtothecontroller.



If you set, for example, the address to channel 20, a fixture in 18 channel mode would use channels 20 to 38                     

forcontrol.



Pleasebesurethatyoudon’thaveanyoverlappingchannelsinordertocontroleachfixturecorrectlyand

independentlyfromanyotherfixtureontheDMXchain.Ifseveralfixturesareaddressedsimilarly,theywillworkin

sync.



PresstheUp/Downbuttonsforsettingthedesiredstartingaddress.Nowyoucanstartoperatingthefixturevia

yourlightingcontroller.

 

11 of 25



Note:

Afterswitchingon,thedevicewillautomaticallydetectwhetherDMX512dataisreceivedornot.Ifthere

isnodatareceivedattheDMXinput,thedisplaywillflash.



Thissituationcanoccurif:

● theXLRplug(cablewithDMXsignalfromcontroller)isnotconnectedwiththeinputofthedevice.

● thecontrollerisswitchedoffordefective,ifthecableorconnectorisdefectiveorthesignalwires

areswappedintheinputconnector.



Note:

It’snecessarytoinserttheXLRterminationplug(with120Ohm)inthelastlightinginthelinkinorderto

ensurepropertransmissionontheDMXdatalink.



DMXProtocol

8bit

16bit

Name

Function

DMX

Pan

Pan Coarse

0-255

Pan Fine

0-255

Tilt

Tilt Coarse

0-255

Tilt Fine

0-255

Movement Speed

Fast to Slow

0-255

Movement

Function

Normal

Movement w/ Blackout

No Function

0-15

16-31

32-255

Shutter Function

Normal Shutter Functions

Pulse Effect Forward

Pulse Effect Reverse

Random Strobe

No Function

0-15

16-31

32-47

48-63

64-255

Shutter

Normal Shutter Functions:

Strobe Rate (Slow to Fast)

Open

Pulse Effect Forward:

Strobe Rate (Slow to Fast)

Open

Pulse Effect Reverse:

Strobe Rate (Slow to Fast)

Open

Random Strobe:

Strobe Rate (Slow to Fast)

Open

0-31

32-223

224-25

0-31

32-223

224-25

0-31

32-223

224-25

0-31

12 of 25

32-223

224-25

Shutter

Shutter Closed

No Function (Shutter Open)

Strobe Effect (Slow to Fast)

No Function (Shutter Open)

Pulse Effect in Sequences

No Function (Shutter Open)

Random Strobe Effect (Slow to Fast)

No Function (Shutter Open)

0-31

32-63

64-95

96-127

128-15

160-19

192-22

224-25

Dimmer

Dimmer (0-100%)

0-255

Dimmer Fine

Dimmer Fine Control

0-255

Virtual Color

Function

On Function

CTC Function

Forward Spin

Reverse Spin

Continuous

Color Bounce

No Function

0-15

16-31

32-47

48-63

64-79

80-111

112-25

Virtual Color 1

Color Temperature Correction 2000K-2700K

White 3200K

White 4200K

White 5600K

White 8000K

Forward Spin Rainbow Effect (Slow to Fast)

Reverse Spin Rainbow Effect (Slow to FasT)

Continuous & Color Bounce:

Blackout

Red

Green

Blue

White

Red=0, Green=Up, Blue=Full, White=0

Red=0, Green=Full, Blue=Down, White=0

Red=Up, Green=Full, Blue=0, White=0

Red=Full, Green=Down, Blue=0, White=0

Red=Full, Green=0, Blue=Up, White=0

Red=Down, Green=0, Blue=Full, White=0

Indexed Color:

Color 1 (Open)

Color 2 - Color 9

0-223

224-23

232-23

240-24

248-25

0-255

0-0

1-1

2-2

3-3

4-4

5-46

47-88

89-130

131-17

173-21

13 of 25

215-25

0-27

28-255

Virtual Color 2

(Only on Color

Bounce)

Color Bounce:

Blackout

Red

Green

Blue

White

Red=0, Green=Up, Blue=Full, White=0

Red=0, Green=Full, Blue=Down, White=0

Red=Up, Green=Full, Blue=0, White=0

Red=Full, Green=Down, Blue=0, White=0

Red=Full, Green=0, Blue=Up, White=0

Red=Down, Green=0, Blue=Full, White=0

0-0

1-1

2-2

3-3

4-4

5-46

47-88

89-130

131-17

173-21

215-25

Red

Red 0-100%

0-255

Red Fine

Red Fine Control

0-255

Green

Green 0-100%

0-255

Green Fine

Green Fine Control

0-255

Blue

Blue 0-100%

0-255

Blue Fine

Blue Fine Control

0-255

White

White 0-100%

0-255

White Fine

White Fine Control

0-255

Zoom

Zoom 10° to 60°

0-255

Zoom Fine

Zoom Fine Control

0-255

Control

Normal

Reset All

Reset Pan & Tilt

No Function

Reset Others

Display Off

Display On

No Function

Hibernate

No Function

0-7

8-15

16-23

24-47

48-55

56-63

64-71

72-87

88-95

96-255

ControlBoard

The Control Board offers several features. You can simply set the starting address, run the preprogrammed               

14 of 25

program,orperformareset.



MainMenu



The main menu is accessed by pressing Enter until the display is lit. Browse through the menu by pressing the                   

arrow buttons (up, down, left, right). Press Enter in order to select the desired menu. You can change the                  

selection by pressing the arrow buttons. Press Enter in order to confirm selection, then exit back to the main                  

menutosavechanges.Thefunctionsprovidedaredescribedinthefollowingsections.



①=BasicReload②=ProgramReload③=PrivateReloadDefaultsettingsarelistedinbold.



MENU

SUBMENU

SELECTION

FUNCTION

Connect

DMXAddress①

XXX

DMXAddressSetting

Light

MaxTemperature①

80~139°C,120°C

176~282°F,248°F

Setinternal

temperaturetoshutthe

unitoff.(Activatesafter

5minutes.)



LampAdjust①

Pan…...

AdjustValue

Information

TimeInfo

CurrentXXXX(Hours)

FixtureLifeXXXX(Hours)

BootTime

TotalRunTime



Temperature

NearLampTemp

TemperatureSensors



FansSpeed

NearLampFan

FanSpeedSensors



ChannelValue

Pan…...

DisplayChannelValue



ErrorMessage

Pan,Tilt…...

ChannelErrors



FixtureModel

[Model&Brand]

DisplayModel&Brand



SoftwareVersion

1U01V.1.0.00

VersionofEachIC

Set

Reset

All

Pan&Tilt

Others

ResetAll

ResetPan&Tilt

ResetOthers



Movement

PanReverse①On/Off

PanReverse

15 of 25

TiltReverse①On/Off

PanDegree①630/540

Encoders①On/Off

Pan/TiltMode①Stand/Smooth

TiltReverse

ChoosePanDegree

EncoderWheelOn/Off

ChoosePan/TiltMode



UISet

MicSens.③0~99%,60%

NoSignal①Close/Hold/Auto/Music

TemperatureC/F①Fahrenheit/Celsius

FansMode①Auto/High

Hibernation①OFF,01M~99M,15M

Backlight①01~60M,02M

FlipDisplay①On/Off

DisplayBright③00~31,10

BrandShow①On/Off

KeyLock①On/Off

Language①En/简/繁/Fr/Sp

SensitivityofMic

ModeWhenNoSignal

TemperatureF°orC°

FanAutoorHigh

SleepTime

BacklightTime

ReverseDisplay180°

BrightnessSetting

ShowBranding

KeyLockOn/Off

LanguageSelect



Users(DMXChannel

Mode)

UserMode①

Standard

Extended

8bit

16bit

User



EditUser③

MaxChannel=XX

Pan=CH01



StandardDMXMode

ExtendedDMXMode

8bitMode

16bitMode

Usermode



EditUserMode



Calibration③

Password=XXX

Color=XXX

Password(050)

EditChannelValue



FixtureID③

Name

Password

PIDCode

Name

Password(050)

SetPIDofRDM



ReloadDefault

BasicReload(①)On/Off

ProgramReload(②)On/Off

PasswordXXX

PrivateReload(③)On/Off

AllReloadOn/Off

BasicReload

ProgramReload

Password(050)

PrivateReload

AllReload

Program

Play①

DMXReceive

SlaveReceiveSlaveReceive1,2,3

SequenceMaster/Standalone

MusicMusic/Standalone

DMXReceive

ChooseSlavePosition

RunSequence

MusicMode



SelectChase②

ChasePart1

Chase1~8Chase1

ChasePart2

Chase1~8Chase2

ChasePart3

Chase1~8Chase3

SelectandRunAuto

Program



EditChase②

Chase1ChaseTest

…Step01=SCXXX

Chase8Step64=SCXXX

Test

BeginningScene

EndingScene



EditScenes②

EditScene001Pan,Tilt…=XXX

~EditSceneFadeTime=XXX

250Scene=XXX

Time

DMXInput

InputManualScene

FadingTime

SceneTime

InputScenefrom

Controller

16 of 25



ScenesRecord

ScXX=>ScXX

AutoInputScenes



Connect



DMXAddressSetting

WiththisfunctionyoucanadjustthedesiredDMXaddressviatheControlBoard.

Select“DMXAddress“bypressingUporDown.

PresstheEnterbuttonthenadjusttheDMXaddressbypressingUporDown.

PresstheEnterbuttontoconfirm.



Light



MaxTemperature

With this function you can set the inside temperature at which the projector will automatically switch the lamp                 

off. Press Up or Down to select the maximum internal temperature between 80°C and 139°C. Internal               

temperatures below 90°C are not critical. 90°C and more should lead to the lamp being switched off after five                  

minutes.Pleasenotethattheoutsidetemperatureshouldnotexceed45°C.



Information



CurrentTimeInformation

With this function you can display the temporary running time of the device from the last power on. The display                   

shows“XXXX”,“X“standsforthenumberofhours.Thecounterisresetafterturningthedeviceoff.



FixtureLife

With this function you can display the running time of the device. The display shows “XXXX”, “X“ stands for the                   

numberofhours.



TemperatureNearLampTemp

WiththisfunctionyoucandisplaythetemperatureintheprojectorheadindegreesCelsius/Fahrenheit.



Fanspeed

Withthisfunctionyoucandisplaythecurrentfanspeed.Thedisplayshows“XXXX”,“X“standsforHz.



Initialstatus

Withthisfunctionyoucandisplaywhichvaluetherespectivechannelswillstart.



Errorchannels

Withthisfunctionyoucandisplaythechannelerrors.



FixtureModel

Withthisfunctionyoucandisplaythemodelnumberandbrandofthefixture.



Softwareversion

WiththisfunctionyoucandisplaythesoftwareversionofeachIC.

1. Select“Softwarever.”bypressingUporDown.

2. PresstheEnterbutton.Thedisplayshowse.g.“1U01VX.X.XX”,“X.X.XX“standsfortheversionnumber.



Set

Reset

WiththisfunctionyoucanresetthedeviceviatheControlBoard.YoucanselectthedifferentResetfunctions

bypressingUporDown.



Movement



PANReverse

Withthisfunctionyoucanreversethepanmovement.

17 of 25



TILTReverse

Withthisfunctionyoucanreversethetiltmovement.



PANDegree

Withthisfunctionyoucanselectthepandegree.

1. Select“PANdegree”bypressingUporDown.

2. PresstheEnterbutton,thedisplayshows“540”.

3. PressUporDowntoselectthedesireddegreebetween“540”and“630”.

4. PresstheEnterbuttontoconfirm.



AutomaticPAN/TILTcalibration

Withthefunction"Encoders"youcancalibratethepan/tiltmovementtothecorrectstartingposition.



AdjustPAN/TILTspeed

Withthisfunctionyoucandefinethepan/tiltspeed.Youcanselectoneoftwodifferentmodes.



UISet



MicSensitivity

Withthisfunction,youcanselectthedesiredmicrophonesensitivitybetween0%and99%.

1. Select“MicSens”bypressingUporDown.

2. PresstheEnterbutton.

3. PressUporDowntoselectthedesiredsensitivity.

4. PresstheEnterbuttontoconfirm.



NoDMXStatus

Withthefunction"NoSignal",youcansetdifferentmodesifthereisnoDMXsignal.

1. Select"Close,Hold,AutoorMusic"bypressingUporDown.

2. PressUporDowntoselectbetween"Close","Hold","Auto"or"Music".

3. PresstheEnterbuttontoconfirm.



SelectTemperatureDesignation

Withthisfunctionyoucanselectthetemperaturedesignation.

1. Select“TemperatureC/F”bypressingUporDown.

2. PressUporDowntoselectthedesireddegreebetween“Celsius”and“Fahrenheit”.

3. PresstheEnterbuttontoconfirm.



HibernationPowerStandbyMode

With this function you can put the device in the power standby mode. This function will be automatically activated                  

after a predefined period of time of no DMX activity. In standby mode the lamp/LEDs and all motors will power                   

down if no DMX signal is sent to the fixture for a period of e. g. 15 minutes (can be user defined). The fixture will                        

automaticallyresetandreturntonormaloperationonceaDMXsignalissent.



Backlight

Withthisfunctionyoucanshutoffthedisplayafter2to60minutes.



FlipDisplay

Withthisfunctionyoucanflipthedisplayby180°forabetterviewwhenthefixtureisinstalledupsidedown.

Shortcut:Press“up”and“down”forthreesecondstoflipthedisplaydirectly.



BrandShow

With this function you can show or hide the brand name on the display during menu               

operation,butstillshowitafterreset.



KeyLock

WiththisfunctionyoucanlockthekeysoftheControlBoardtoe.g.preventmenutampering.Ifthisfunctionis

18 of 25

activated,thekeyswillbeautomaticallylockedassoonasyouexitthemenu.Inordertodeactivateor

temporarilydeactivatethekeylockfunction,pressUPDOWNLEFTRIGHTENTERtoregainaccesstothe

menucommands.



Users



Usermode

Withthisfunctionyoucancreateuserdefinedchannelorders.



EditUser

Withthisfunctionyoucanadjustthepresetuserdefinedchannelorder.



Calibration

Withthisfunction,youcancalibrateandadjusttheeffectwheelstotheircorrectpositions.Thepasswordfor

thisfunctionis“050“.



FixtureID



RDM

WiththisfunctionyoucancallupvarioussubmenusviaRDM.



ThisdeviceisRDMready.RDMstandsfor"RemoteDeviceManagement"andmakesremotecontrolofdevices

connectedtotheDMXbuspossible.ANSIE1.202006byESTAspecifiestheRDMstandardasanextensionof

theDMX512protocol.



ManualsettingslikeadjustingtheDMXstartingaddressarenolongerneeded.Thisisespeciallyusefulwhenthe

deviceisinstalledinaremotearea.



RDMisintegratedinDMXwithoutinfluencingtheconnections.TheRDMdataistransmittedviathestandardXLR

poles1and2—newDMXcablesarenotnecessary.RDMreadyandconventionalDMXdevicescanbeoperated

inoneDMXline.TheRDMprotocolsendsitsownpackagesintheDMX512datafeedanddoesnotinfluence

conventionaldevices.



IfDMXsplittersareusedandRDMcontrolistobeused,thesesplittersmustsupportRDM.



ThenumberandtypeofRDMparametersdependonthe(optional)RDMcontrollerbeingused.



RDMParameterID's(Slot2122)

Value

Category_NetworkManagement



DISC_UNIQUE_BRANCH

0x0001

DISC_MUTE

0x0002

DISC_UN_MUTE

0x0003

CategoryRDMInformation



SUPPORTED_PARAMETERS

0x0050

PARAMETER_DESCRIPTION

0x0051

Category_ProductInformation



DEVICE_INFO

0x0060

19 of 25

DEVICE_MODEL_DESCRIPTION

0x0080

MANUFACTURER_LABEL

0x0081

DEVICE_LABEL

0x0082

FACTORY_DEFAULTS

0x0090

SOFTWARE_VERSION_LABEL

0x00C0

CategoryDMX512Setup



DMX_PERSONALITY

0x00E0

DMX_PERSONALITY_DESCRIPTION

0x00E1

DMX_START_ADDRESS

0x00F0

SLOT_INFO

0x0120

SLOT_DESCRIPTION

0x0121

Category_Sensors



SENSOR_DEFINITION

0x0200

SENSOR_VALUE

0x0201

Category_Power/LampSettings

0x04xx

DEVICE_HOURS

0x0400

CategoryDisplaySettings



DISPLAY_INVERT

0x0500

Category_Configuration



PAN_INVERT

0x0600

TILT_INVERT

0x0601

Category_Control



IDENTIFY_DEVICE

0x1000

RESET_DEVICE

0x1001



ReloadDefault

Withthisfunctionyoucanrestorethefactorysettingsofthedevice.Thedifferentsettings(markedinthetable)

willbesetbacktothedefaultvalues(shaded).



Program



PlaySlaveDevice

Withthisfunction,youcandefinethedeviceasaslave.YoucanchooseoneofthreedifferentSlaveprograms.

Forfurtherinformationsee“EditChase”.



Sequence

With this function, you can run the internal program. You can select the desired program under “Select Chase”.                 

You can set the number of steps under “Edit Chase”. You can edit the individual scenes under “Edit Scenes”.                  

With this function you can run the individual scenes either automatically, i.e. with the adjusted step time. The                 

20 of 25

Page is loading ...

OmniSistem Spark 7 Zoom User manual

Brand: OmniSistem

Model: Spark 7 Zoom

Category: Stroboscopes & disco lights

Type: User manual

Download PDF

report

OmniSistem Spark 7 Zoom User manual

OmniSistem Spark 7 Zoom User manual

Other documents