ProLights PANORAMAIPSPOT User manual

USER MANUAL

MANUALE UTENTE

PANORAMAIPSPOT

HYBRID MOVING

EN - IT

reproduced in any form or by any means for any commercial use.

In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the

characteristics stated in this instruction manual at any time and without prior notice.

All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it

REV. 01-09/18

1

PANORAMAIPSPOT

Packing content

• PANORAMAIPSPOT

• Mount bracket

• Power supply cable and signal cable

• Safety rope

• User manual

TABLE OF CONTENTS

Safety

General instructions

Warnings and installation precautions

1 Introduction

1. 1 Description

1. 2 Technical specications

1. 3 Operating elements and connections

2 Installation

2. 1 Mounting

3 Functions and settings

3. 1 Operation

3. 2 Basic

3. 3 Menu structure

3. 4 Connect

DMX address

DMX Mode

Wireless

Artnet

RDM

3. 5 DMX Addressing

3. 6 Connection of the DMX line

3. 7 Construction of the DMX termination

3. 8 DMX Channel

3. 9 Gobos

3. 10 Setup

3. 11 Advanced

3. 12 Information

3. 13 Automatic Mode

4 Maintenance

4. 1 Maintenance and cleaning the unit

4. 2 Trouble shooting

2

3

6

7

8

9

11

12

13

14

22

23

24

25

26

29

30

PANORAMAIPSPOT

2

WARNING! Before carrying out any operations with the unit, carefully read this instruction

manual and keep it with cure for future reference. It contains important information about

the installation, usage and maintenance of the unit.

SAFETY

General instruction

• The products referred to in this manual conform to the European Community Directives and are there-

fore marked with .

• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.

Never make any modications on the unit not described in this instruction manual, otherwise you will

risk an electric shock.

• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-

cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units

from indirect contact and/or shorting to earth by using appropriately sized residual current devices.

• The connection to the main network of electric distribution must be carried out by a qualied electrical

installer. Check that the main frequency and voltage correspond to those for which the unit is designed

as given on the electrical data label.

• This unit is not for home use, only professional applications.

• Never use the xture under the following conditions:

- in places subject to vibrations or bumps;

- in places with an ambient temperature of over 45°C.

• Make certain that no inammable liquids, water or metal objects enter the xture.

• Do not dismantle or modify the xture.

• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for

an inspection or contact the manufacturer directly.

• If the unit is to be put out of operation denitively, take it to a local recycling

plant for a disposal which is not harmful to the environment.

Warnings and installation precautions

• If this device will be operated in any way dierent to the one described in this manual, it may suer

damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like

short circuit, burns, electric shock, etc.

• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.

• Always additionally secure the projector with the safety rope. When carrying out any work, always com-

ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country

in which the xture’s being used.

• For inside use only. Not designed for outside use.

• The minimum distance between the xture and surrounding walls must be more than 50 cm and the

air vents at the housing must not be covered in any case.

• Install the xture in a well ventilated place.

• Keep any inammable material at a safe distance from the xture.

• The maximum temperature that can be reached on the external surface of the tting, in a thermally

steady state, is high. After power o, please cool down over 15 minutes.

• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent

that their eectiveness is impaired.

• The lamp (LED) shall be changed if it has become damaged or thermally deformed.

• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may

trigger epileptic seizures in photosensitive persons or persons with epilepsy.

3

PANORAMAIPSPOT

- 1 - INTRODUCTION

1.1 TECHNICAL SPECIFICATIONS

PANORAMAIPSPOT is a powerful and exible IP rated moving LED spot designed to deliver a stunning

brightness level, all packaged in a compact housing. Equipped with a 1:10 zoom and a complete feature

set, the PANORAMAIPSPOT really stands out in any environment be it festivals, arenas or large outdoor

events.

LIGHT SOURCE

• Source: 420W high-power white LED

• CT: 7.000K

• Lux: (5°) 21’362lx @5 m

• Lux: (50°) 1’173lx @5 m full

• Source life expectancy: >20.000 h

OPTICS

• Zoom: 5°-50° motorised linear zoom

• Lens diameter: 120mm

• Lens type: HD anti-reection lenses with achromatic coating

• Focus: motorised with auto-focus

COLOUR SYSTEM

• Colour mixing: linear CMY

• CTC: linear CTO correction 2700 ~ 6000 K

• Colour wheel: 8 dichroic lters + open

DYNAMIC EFFECTS

• Rotating gobos: 7 rotating gobos + open, interchangeable, indexing

• Gobo size: outer: 26 mm - image: 19 mm - max thickness: 2 mm

• Fixed gobos: 6 xed gobos + open, interchangeable

• Gobo size: outer: 26 mm - image: 19 mm - max thickness: 0.5 mm

• Circular prism: 3f with bi-directional rotation, indexing

• Frost: linear 0 - 100% frost lter

• Iris: 5-100% motorised linear iris

BODY

• Pan angle: 540 - 630°

• Tilt angle: 233°

• Pan/Tilt resolution: 8 / 16 bit

• Feedback: automatic repositioning after accidental movement

• Body: aluminium structure with hi-resistance polycarbonate cover

• Body colour: black

CONTROL

• Protocols: DMX512, RDM, Art-Net, W-DMX

• DMX channels: 19 / 21 / 28 / 29 / 36channel

• W-DMX: included, wireless solution receiver

• RDM: RDM ready for xture remote monitor and settings

• Display: LCD high resolution colour display

• Firmware upgrade: yes, via USB - DMX interface (UPBOX2) not included

PANORAMAIPSPOT

4

• Hibernation: power safe mode when lost DMX

ELECTRONICS

• Dimmer: linear 0 ~ 100% electronic dimmer

• Strobe / shutter: 1-28 Hz, electronic

• Battery backup: battery backup for user operation without connecting to the main power

• Operating temperature: -20° ~ +45°

ELECTRICAL

• Power supply: 100-240 V – 50/60 Hz

• Power consumption (at 230 V): 492W

• Power consumption (at 120 V): 501W

PHYSICAL

• Cooling: combination of heat pipe cooling system and low noise fan

• Sospension and xing: any position with quick-lock omega brackets

• Pan / tilt lock: pan / tilt locking for transportation and maintenance

• Signal connection: Amphenol XLR 5p IN/OUT connectors

• Data connection: Art-Net RJ45 IN/OUT

• Power connection: Seetronic powerCON waterproof IN/OUT connectors

• IP rating: 65 for temporary outdoor application, not for xed installation

• Dimensions (WxHxD): 441x740x316mm

• Weight: 38kg

474,4

420

312

740,2

5

PANORAMAIPSPOT

Fig.1

Technical drawing

1

2

3

5

6

4

8 7

109

11 12

A

B

PANORAMAIPSPOT

6

1.2 OPERATING ELEMENTS AND CONNECTIONS

1. MOVING HEAD

2. ROTARY ARM

3. HANDLE

4. CONTROL PANEL with LCD display

and 5 button used to access

the control panel functions and

manage them.

5. LED INDICATOR "W-DMX"

6. LED INDICATOR POWER

7. ANTENNA

8. EtherCON connector Signal IN/

OUT

9. EtherCON connector Signal IN/

OUT

10. POWER IN (PowerCON TRUE

IN): for connection to a socket

(100-240V~/50-60Hz) via the

supplied mains cable.

11. DMX IN (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

12. DMX OUT (5-pole XLR):

1 = ground, 2 = DMX-, 3 = DMX+,

4 N/C, 5 N/C

Fig.2

View A

View B

7

PANORAMAIPSPOT

Fig.3

CLAMP

SAFETY

CABLE

OMEGA

BRACKETS

- 2 - INSTALLATION

2.1 MOUNTING

The PANORAMAIPSPOT may be set up on a solid and even surface. By means of the xing facilities of the

baseplate, the unit can also be mounted upside down to a cross arm. The base plate is shown in g.3. For

xing, stable mounting clips are required. According to the gure, the bolts of the brackets are placed into

the openings provided in the base plate and turned clockwise until they lock (to the stop). Always ensure

that the unit is rmly xed to avoid vibration and slipping while operating. The mounting place must be of

sucient stability and be able to support a weight of 10 times of the unit’s weight. When carrying out any

installation, always comply scrupulously with all the regulations (particularly regarding safety) currently

in force in the country in which the xture’s being used. Always additionally secure the projector with the

safety rope from falling down. For this purpose, fasten the safety rope at a suitable position so that the

maximum fall of the projector will be 20 cm.

PANORAMAIPSPOT

8

- 3 - FUNCTIONS AND SETTINGS

3.1 OPERATION

Connect the supplied main cable to a socket (100-240V~/50-60Hz). The unit will run built-in program to

reset all motors to their home position. Shortly after that the PANORAMAIPSPOT is ready for operation.

To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-

mended to connect the unit to a socket which can be switched on and o via light switch.

3.2 BASIC

The PANORAMAIPSPOT has a LCD display and 5 button used to access the control panel functions and

manage them (g.4).

Fig.4 - Functions of the buttons and display icons

LEFT RIGHT UP DOWN ENTER BATTERY

Return to the top

level

Commute from

units, tens, hundred

in the menu

Increases the value

displayed or passes

to the previous item

in a menu

Decreases the value

displayed or passes

to the next item in

the menu

Conrms the

displayed value,

or activates the

displayed function,

or enters the

successive menu

Used to activate the

backup battery. It

allows to switching

display interface

without main power

SPOT

CONNECT

LIGHT

INFORMATION

SET

PROGRAM

9

PANORAMAIPSPOT

3.3 MENU STRUCTURE

MENU

1 CONNECT

ð

Address

ð

DMX

ð

Value (1-512)

W-DMX

ð

Value (1-512)

Artnet

ð

Value (1-512)

DMX Mode

ð

Mode

ð

Standard; Extended; Basic-8bit; Basic-16bit;

Extended-16bit; User;

Edit User

ð

Max Channel=XX / PAN= CH01

Wireless

ð

DMX Out

ð

OFF/ON

Reset Connect

ð

NO/YES

Ethernet

ð

DMX Out

ð

OFF/ON

IP Address

ð

xxx.xxx.xxx.xxx

IP Mask

ð

255.0.0.0

Universe

ð

xxxxxx

RDM ID

ð

Name

ð

Fixture ID Name

Mode

ð

Mode1 / Mode2 (Model)

Password

ð

050 (unlocks the following settings)

PID Code

ð

xxxxx

2 SET UP

ð

Temperature

ð

Temperature C/F

ð

Celsius/Fahrenheit

Max Temperature

ð

Value (60°~90° C)

Movement

ð

Pan Reverse

ð

YES/NO

Tilt Reverse

ð

YES/NO

Pan Degree

ð

540/630

Feedbacks

ð

YES/NO

Pan/Tilt Mode

ð

Standard/Smooth

Screen

ð

Backlight

ð

Always On / 01 ~ 99m

Flip Display

ð

YES/NO/AUTO

Key Lock

ð

ON/OFF

Language

ð

EN/FR/SP...

Fixture

ð

Fans Mode

ð

Auto Speed/High Speed

No Signal

ð

Close/Hold/Auto/Music

Hibernation

ð

Disable/Min (01-99)

Theatre Mode

ð

YES/NO

Frequency

ð

600Hz ... (1200Hz)

Adjust

ð

Pan, Pan Fine, Tilt, Tilt

Fine, Pan&Tilt Speed,

Shutter, Dimmer, [...]

ð

Value (000-255) for each function

PANORAMAIPSPOT

10

3 ADVANCED

ð

Reset

ð

All

Pan & Tilt

Others

Calibration

ð

Password

ð

050 (unlocks the following settings)

Pan

ð

Value

Others

Reload Default

ð

Basic Reload

ð

ON/OFF

Program Reload

ð

ON/OFF

Password

ð

050 (unlocks the following settings)

Private Reload

ð

ON/OFF

All Reload

ð

ON/OFF

4 INFORMATION

ð

Time I nfo.

Current XXXX(Hours)

Fixture Life XXXX(Hours)

Temperature Near Lamp Temp (depends on xture)

Fans Speed Near Lamp Fan (depends on xture)

Channel Value Pan......

Error Message Pan,Tilt,.......

Fixture Model xxxxxx

Software Ver. 1U01 V1.0.00.......

5 STAND ALONE

ð

Play

ð

DMX Receive

Slave Receive

ð

Part 1-2-3 Receive

Static

ð

xxx Scene

Sequence

ð

Alone/Master

Music

ð

Alone/Master

Mic Sens.

ð

Value (00-99%)

Select Chase

ð

Chase Part 1

ð

Chase 1 - Chase 8

Chase Part 2 Chase 1 - Chase 8

Chase Part 3

ð

Chase 1 - Chase 8

Edit Chase

ð

Chase 1

ð

Step 1 - 64

Chase 2 Step 1 - 64

....

Chase 8

ð

Step 1 - 64

Edit Scenes

ð

Edit Scenes 001

ð

Pan/Pan Fine/Tilt/Tilt Fine/...

Edit Scenes ...

ð

Pan/Tilt/CMY, Gobo1...

Edit Scenes 250

ð

Pan/Tilt/CMY, Gobo1...

Scenes Record

ð

Sc XX - Sc XX

11

PANORAMAIPSPOT

3.4 CONNECT

Several units may be interconnected in order to control all further slave units to the same eect of the

master unit.

1. Connect the DMX OUT of the master unit via 5-pole XLR cable to the DMX IN of the rst slave unit.

2. Connect the DMX OUT of the rst slave unit to the DMX IN of the second slave unit, etc. until all units

are connected in a chain.

DMX ADDRESSING

To enter the DMX mode, follow these steps:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select the Address and press the ENTER key.

• Press the arrow keys to select the desired value (001-512).

• Press the ENTER key to conrm the setting.

• Press the LEFT button repeatedly to exit the menu and save changes.

DMX MODE

The PANORAMAIPSPOT has 5 DMX channel congurations which can be accessed from the control panel.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select DMX Mode and press the ENTER button to

enter the next menu.

• Press the UP/DOWN button to scroll through the menu, select Mode and press ENTER to conrm your

choice.

• Use the UP/DOWN button to select the desired DMX channel conguration (Standard, Extended, Basic-8bit,

Basic-16bit,Extended2, User), then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

The tables on page 14 show the mode of operation and their values DMX.

The unit is equipped with 3/5-pole XLR connections.

WIRELESS

To enable wireless control mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu Wireless.

• Press the UP/DOWN button to scroll through the menu, select Receive on/o and press ENTER to activate

the wireless mode.

• Press the UP/DOWN button to scroll through the menu, select Reset Connect to reset the wireless con-

nection of the unit.

ARTNET

To enable Artnet mode, proceed as follows:

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Connect icon, then press the ENTER button to

enter the next menu Ethernet.

• Press the UP/DOWN button to scroll through the menu, select DMX Out, IP Address, IP Mask, Universe, and

press ENTER to activate the mode.

PANORAMAIPSPOT

12

ID and RDM

With this function you can call up various submenus via RDM.

This device is RDM ready. RDM stands for “Remote Device Management” and makes remote control of

devices connected to the DMX-bus possible. Manual settings like adjusting the DMX starting address are

no longer needed. This is especially useful when the device is installed in a remote area. RDM is integrated

in DMX without inuencing the connections. The RDM-data is transmitted via the standard XLR-poles 1

and 2 – new DMX-cables are not necessary. RDM ready and conventional DMX devices can be operated

in one DMX line. The RDM protocol sends own packages in the DMX512 data feed and does not inuence

conventional devices. If DMX splitters are used and RDM control is to be used, these splitters must sup-

port RDM. The number and type of RDM parameters depend on the RDM controller (not included) is used.

• Press the ENTER button to access the main menu.

• Press the UP/DOWN button to scroll the menu, select the Set icon, then press the ENTER button to enter

the next menu.

• Press the UP/DOWN button to scroll through the menu, and then select the Fixture ID and press the

ENTER button to enter the next menu.

• Press UP/DOWN button to scroll through the menu, then select Password and press ENTER to conrm.

• Use the arrow keys to enter the password 050 and press ENTER to conrm.

• Once you have entered your password, you can set the PID Code, necessary to control the unit with the

RDM protocol. Press the UP/DOWN button to scroll through the menu, select PID Code and press EN-

TER to conrm.

• Use the arrow keys to enter the PID Code, then press the ENTER button to conrm your choice.

• Press the LEFT button repeatedly to exit the menu and save changes.

3.5 DMX ADDRESSING

For operation via light control unit with DMX512 protocol, is sucient connect the controller to PANORA-

MAIPSPOT. To able to operate the PANORAMAIPSPOT with a light controller, adjust the DMX start address

for the rst a DMX channel. If e. g. address 33 on the controller is provided for controlling the function of

the rst DMX channel, adjust the start address 33 on the PANORAMAIPSPOT. The other functions of the

light eect panel are then automatically assigned to the following addresses.

An example with the start address 33 is shown below:

Number of

DMX channels

Start address

(example)

DMX Address

occupied

Next possible start

address for unit No. 1

Next possible start

address for unit No. 2

Next possible start

address for unit No. 3

21 33 33-53 54 74 95

DMX Address: 102DMX Address: 56DMX Address: 33 DMX Address: 79

Fig.5 - Example 23 DMX channels conguration

. . . . . . . . . . . .

DMX512 Controller

13

PANORAMAIPSPOT

3.6 CONNECTION OF THE DMX LINE

DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω imped-

ance and low capacity.

The following diagram shows the connection mode:

Fig.6

DMX - OUTPUT

XLR socket

DMX - INPUT

XLR plug

Pin1 : GND - Shield

Pin2 : - Negative

Pin3 : + Positive

Pin4 : N/C

Pin5 : N/C

ATTENTION

The screened parts of the cable (sleeve) must never be connected to the system’s earth, as this would

cause faulty xture and controller operation.

Over long runs can be necessary to insert a DMX level matching amplier.

For those connections the use of balanced microphone cable is not recommended because it cannot

transmit control DMX data reliably.

• Connect the controller DMX input to the DMX output of the rst unit.

• Connect the DMX output to the DMX input of the following unit. Connect again the output to the input

of the following unit until all the units are connected in chain.

• When the signal cable has to run longer distance is recommended to insert a DMX termination on the

last unit.

3.7 CONSTRUCTION OF THE DMX TERMINATION

The termination avoids the risk of DMX 512 signals being reected back along the cable when they reach-

es the end of the line: under certain conditions and with certain cable lengths, this could cause them to

cancel the original signals.

The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the 5-pin male XLR

connector, as shown in gure.

Fig.7

Example:

5 pin XLR connector

PANORAMAIPSPOT

14

3.8 DMX CHANNELS

STD EXT BAS-8 BAS-16 EXT2

FUNCTION

DMX

Value

28 Ch 29 Ch 19 Ch 21 Ch 36 Ch

1 1 1 1 1

PAN

0~100% 000 - 255

2 2 2 2

PAN FINE

0~100% 000 - 255

3 3 2 3 3

TILT

0~100% 000 - 255

4 4 4 4

TILT FINE

0~100% 000 - 255

5 5 3 5 5

P/T SPEED

Fastest to slowest 000 - 255

6 6

P/T FUNCTION

Normal

Movement with Blackout

TBD (not used)

000 - 015

016 - 031

032 - 255

6 7 7

SHUTTER FUNCTION

Normal Shutter Functions

Pulse-eect Forward

Pulse-eect Reverse

Random strobe

TBD (not used)

000 - 015

016 - 031

032 - 047

048 - 063

064 - 255

7 8 8

SHUTTER

Normal Shutter Functions

Close

Strobe Rate (slow to fast)

Open

Pulse-eect Forward

Close

Strobe Rate (slow to fast)

Open

Pulse-eect Reverse

Close

Strobe Rate (slow to fast)

Open

Random Strobe

Close

Strobe Rate (slow to fast)

Open

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

000 - 031

032 - 223

224 - 255

4 6

SHUTTER

Shutter closed

No function (shutter open)

Strobe eect slow to fast

000 - 031

032 - 063

064 - 095

15

PANORAMAIPSPOT

STD EXT BAS-8 BAS-16 EXT2

FUNCTION

DMX

Value

28 Ch 29 Ch 19 Ch 21 Ch 36 Ch

4 6

No function (shutter open)

Pulse-eect in sequences

No function (shutter open)

Random strobe eect slow to fast

No function (shutter open)

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

8 9 5 7 9

DIMMER

Dimmer (0% to 100%) 000 - 255

10

DIMMER FINE

White (0% to 100%) 000 - 255

9 10 11

COLOR FUNCTION

Indexed

Indexed with Blackout

Forward Spin

Reverse Spin

Continuous

Color Bounce (from slow to fast)

TBD (not used)

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 111

112 - 255

10 11 12

COLOR

Indexed - Indexed w. Blackout - Bounce

1 - Open

2 - Open / Dark Red

3 - Dark Red

4 - Dark Red / Pink

5 - Pink

6 - Pink / Amber

7 - Amber

8 - Amber / Light Green

9 - Light Green

10 - Light Green / Dark Blue

11 - Dark Blue

12 - Dark Blue / Aquamarine

13 - Aquamarine

14 - Aquamarine / Congo Blue

15 - Congo Blue

16 - Congo Blue / CTC 3200 K

17 - CTC 3200 K

18 - CTC 3200 K / Open

Forward Spin

Stop to fastest

Reverse Spin

Stop to fastest

Continuous

Positioning from 0 -360 degrees

000 - 013

014 - 027

028 - 041

042 - 055

056 - 069

070 - 083

084 - 097

098 - 111

112 - 125

126 - 139

140 - 153

154 - 167

168 - 181

182 - 195

196 - 209

210 - 223

224 - 237

238 - 255

000 - 255

PANORAMAIPSPOT

16

STD EXT BAS-8 BAS-16

EXT2

FUNCTION

DMX

Value

28 Ch 29 Ch 19 Ch 21 Ch

36 Ch

6 8

COLOR

Indexed

1 - Open

2 - Open / Dark Red

3 - Dark Red

4 - Dark Red / Pink

5 - Pink

6 - Pink / Amber

7 - Amber

8 - Amber / Light Green

9 - Light Green

10 - Light Green / Dark Blue

11 - Dark Blue

12 - Dark Blue / Aquamarine

13 - Aquamarine

14 - Aquamarine / Congo Blue

15 - Congo Blue

16 - Congo Blue / CTC 3200 K

17 - CTC 3200 K

18 - CTC 3200 K / Open

Indexed with Blackout

1 - Open

2 - Open / Dark Red

3 - Dark Red

4 - Dark Red / Pink

5 - Pink

6 - Pink / Amber

7 - Amber

8 - Amber / Light Green

9 - Light Green

10 - Light Green / Dark Blue

11 - Dark Blue

12 - Dark Blue / Aquamarine

13 - Aquamarine

14 - Aquamarine / Congo Blue

15 - Congo Blue

16 - Congo Blue / CTC 3200 K

17 - CTC 3200 K

18 - CTC 3200 K / Open

Indexed with Bounce

1 - Open

2 - Dark Red

3 - Pink

4 - Amber

5 - Light Green

6 - Dark Blue

6 - Aquamarine

7 - Congo Blue

8 - CTC 3200 K

Forward Wheel Spin

Stop to fastest

Reverse Wheel Spin

Stop to fastest

000 - 002

003 - 005

006 - 008

009 - 011

012 - 014

015 - 017

018 - 020

021 - 023

024 - 026

027 - 029

030 - 032

033 - 035

036 - 038

039 - 041

042 - 044

045 - 047

048 - 050

051 - 053

054 - 056

057 - 059

060 - 062

063 - 065

066 - 068

069 - 071

072 - 074

075 - 077

078 - 080

081 - 083

084 - 086

087 - 089

090 - 092

093 - 095

096 - 098

099 - 101

102 - 104

105 - 106

107 - 119

120 - 132

133 - 145

146 - 158

159 - 171

172 - 184

185 - 197

198 - 210

211 - 223

224 - 239

240 - 255

17

PANORAMAIPSPOT

STD EXT BAS-8 BAS-16 EXT2

FUNCTION

DMX

Value

28 Ch 29 Ch 19 Ch 21 Ch 36 Ch

11 12 7 9 13

CYAN

0~100%

000 - 255

14

CYAN FINE

0~100% 000 - 255

12 13 8 10 15

MAGENTA

0~100% 000 - 255

16

MAGENTA FINE

0~100% 000 - 255

13 14 9 11 17

YELLOW

0~100% 000 - 255

18

YELLOW FINE

0~100% 000 - 255

14 15 10 12 19

CTO

0~100% 000 - 255

20

CTO FINE

0~100% 000 - 255

15 16 21

ROTATING GOBO FUNCTION

Indexed

Indexed with Blackout

Forward Spin

Reverse Spin

Continuous

Shake

TBD (not used)

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 095

096 - 255

16 17 22

ROTATING GOBO

Indexed - Indexed w. Blackout

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Forward - Reverse Wheel Spin

Stop to fastest

Continuous

Positioning from 0-360 degrees

Shake

(from slow to fast for each gobo)

Continuous

Positioning from 0-360 degrees

000 - 031

032 - 063

064 - 095

096 - 127

128 - 159

160 - 191

192 - 223

224 - 255

000 - 255

PANORAMAIPSPOT

18

STD EXT BAS-8 BAS-16 EXT2

FUNCTION

DMX

Value

28 Ch 29 Ch 19 Ch 21 Ch 36 Ch

11 13

ROTATING GOBO

Indexed

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Indexed with Blackout

Open

Gobo 1

Gobo 2

Gobo 3

Gobo 4

Gobo 5

Gobo 6

Gobo 7

Indexed with Shake

Gobo 1 (from slow to fast)

Gobo 2 (from slow to fast)

Gobo 3 (from slow to fast)

Gobo 4 (from slow to fast)

Gobo 5 (from slow to fast)

Gobo 6 (from slow to fast)

Forward Wheel Spin

Stop to fastest

Reverse Wheel Spin

Stop to fastest

000 - 005

006- 011

012- 017

018 - 023

024 - 029

030 - 035

036 - 041

042 - 047

048 - 053

054 - 059

060 - 065

066 - 071

072 - 077

078 - 083

084 - 089

090 - 097

098 - 115

116 - 133

134- 151

152 - 169

170 - 187

188 - 205

224 - 239

240 - 255

17 18 23

GOBO ROTATION FUNCTION

Continuous

Forward Spin

Reverse Spin

Forward Animate Rotate

Forward Animate Rotate with Blackout

Reverse Animate Rotate

Reverse Animate Rotate with Blackout

TBD (not used)

000 - 015

016 - 031

032 - 047

048 - 063

064 - 079

080 - 095

096 - 111

112 - 255

18 19 24

GOBO ROTATION FUNCTION

Continuous

Positioning from 0-360 degrees

Forward & Reverse Spin

Stop to fastest

Forward & Reverse Animate Rotate

Stop to fastest

000 - 255

000- 255

000 - 255

Page is loading ...

ProLights PANORAMAIPSPOT User manual

ProLights PANORAMAIPSPOT User manual

in other languages

Related papers

Other documents