M O T O R C YC L E S TA N D
OWNER’S MANUAL
WARNING: Read carefully and understand all INSTRUCTIONS
before operating. Failure to follow the safety rules and other basic
safety precautions may result in serious personal injury.
Item #148852
Page of 6
2
Thank you very much for choosing a ULTRA-TOW™ Product! For future reference, please complete the
owner’s record below:
Model: _______________ Purchase Date: _______________
Save the receipt, warranty and these instructions. It is important that you read the entire manual to become
familiar with this product before you begin using it.
This motorcycle stand is designed for certain applications only. The distributor cannot be responsible for issues
arising from modification. We strongly recommend this stand not be modified and/or used for any application
other than that for which it was designed. If you have any questions relative to a particular application, DO NOT
use the stand until you have first contacted the distributor to determine if it can or should be performed on the
product.
For technical questions please call 1-800-222-5381.
INTENDED USE
This motorcycle stand with wheel chock and an adjustable wheel-locking system can accommodate front or rear
motorcycle wheel sizes from 15in. to 22in.
TECHNICAL SPECIFICATIONS
Item
Description
Overall Dimensions
36in.L x 35 1/4in.W x 16 1/8in.H (91 x 90 x 41cm)
Weight Capacity
1800 lbs. (816.5kg)
Wheel size
15in. to 22in. (38 to 56cm)
GENERAL SAFETY RULES
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may
result in serious injury.
WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot
cover all possible conditions or situations that could occur. It must be understood by the operator that
common sense and caution are factors which cannot be built into this product, but must be supplied by the
operator.
SAVE THESE INSTRUCTIONS
WORK AREA
• Keep the work area clean, free of clutter and well lit. Cluttered and dark work areas can cause
accidents.
• Keep children and bystanders away while using this motorcycle stand. Distractions can result in a
loss of control, so bystanders should be kept a safe distance from the work area.
Page of 6
3
• Be aware of all power lines, electrical circuits, water pipes and other mechanical hazards in your
work area, particularly those hazards below the work surface hidden from the operator’s view that may
be unintentionally contacted and may cause personal harm or property damage.
•
PERSONAL SAFETY
• Maintain a safe working environment. Make sure there is adequate surrounding workspace. Do not
use this product in a damp or wet location.
• Use the correct product for your motorcycle. Make sure the motorcycle’s wheel fits into the Wheel
Chock prior to first use.
USE AND CARE
• Use only the accessories that are recommended by the manufacturer for your model. Accessories
that may be suitable for one model may create a risk of injury when used on another model.
• Never leave a motorcycle running while unattended.
ASSEMBLY
• Measure the motorcycle wheel prior to assembly so that the Motorcycle Stand can be adjusted to fit the
wheel length. The Motorcycle Stand will fit most standard motorcycles currently on the market. However,
some models with especially wide tires or custom low-profile front fenders will not fit.
• Mount the Support Arm (4) to the front of the Base using 2 Bolts (12), Washers (5), and Nuts (6)
• Insert Pin (9) through the mounting holes and Cradle Stop (3); secure with Washer (10) and R Pin (11).
• Insert Pin (9) through the mounting holes and Wheel Adapter (2); secure with Washer (10) and R Pin
(11).
• Securely tighten all hardware before use.
• The Motorcycle Stand must be mounted securely to floor, trailer, truck bed or motorcycle lift before use.
Mounting in Concrete
• Choose a location to install the Motorcycle Stand that is flat, level, and capable of bearing the combined
weight of the Motorcycle Stand and the motorcycle being secured. The location should not obstruct
walkways and provide enough room to retrieve the motorcycle after it is mounted. The surface of the
location should be one suitable for the mounting of heavy equipment.
• Use the mounting holes in the Base (1) of the Stand as a template. Arrange the Base in the chosen
location and mark where the holes are to be drilled.
• You will need concrete anchors (not included) to secure the Base to the concrete floor. Using the correct
size concrete drill bit (not included), drill the mounting holes to secure the Base.
• Attach the concrete anchors to the floor. Secure the Base to the floor using concrete anchors
NOTE: Do not sit on the motorcycle when it is loaded in the Motorcycle Stand.
Page of 6
4
Truck Bed Mounting
• Place the Base in the desired position on the mount location. Use the holes in the Base as a pattern to
mark where to drill the holes for the hardware to mount the Stand.
WARNING: Verify that the installation surface has no hidden wires, brake lines, etc. before
drilling.
• Use a power drill (not included) and a steel cutting drill bit (not included) to drill holes in the mount
location.
• Attach the Base to the mount location utilizing the appropriate hardware (not included).
OPERATION
WARNING: Do not drive motorcycle into the Motorcycle Stand.
• Select the correct mounting hole for the motorcycle being loaded on the Stand, and adjust the location
of the Cradle Stop to fit the tire length properly.
• To load a motorcycle, lower the Wheel Adapter to the horizontal position and simply push the motorcycle
into the Stand. The Wheel Adapter will close on the motorcycle tire, securing the bike in an upright
position.
• The motorcycle should be secured with belts or straps (not included).
• To dismount the motorcycle, pull back firmly and steadily until the motorcycle rolls free of the Stand.
MAINTENANCE
• Before each use, inspect the general condition of the Motorcycle Stand. Check for loose screws, poor
alignment or binding of moving parts, cracked or broken parts, and any other condition that may affect
its safe operation. Do not use damaged equipment.
• Occasionally, wipe the Motorcycle Stand down with soft cloth and mild detergent.
Page of 6
5
DIAGRAM & PARTS LIST
Part#
Description
Qty.
Part#
Description
Qty.
1
Base
1
8
Eyelet
2
2
Wheel Adapter
1
9
Pad
2
3
Cradle Stop
1
10
Pin
2
4
Support Arm
1
11
Washer Dia.12
4
5
Washer Dia.10
2
12
R-Pin
4
6
Nut M10
2
13
Bolt M10x45
2
For replacement parts and technical questions, please call 1-800-222-5381.
Page of 6
6
WARRANTY
One-Year Limited Warranty
Distributed by
Northern Tool + Equipment Co., Inc.
Burnsville, MN 55306-6936
Made in China
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Harbor Freight Tools 97071 User manual
-
Pittsburgh Item 97841 Owner's manual
-
Pittsburgh Item 61670-UPC 193175224668 Owner's manual
-
Pittsburgh Item 60392 Owner's manual
-
Pittsburgh Motorcycle Wheel Chock Owner's manual
-
Pittsburgh WHEEL CHOCK Owner's manual
-
-
HAUL MASTER 99900 Set Up And Operating Instructions Manual
-
VEVOR TY210075 User manual
-
Power Fist 8674285 User manual
