Monogram ZV750SY Installation guide

Brand: Monogram

Model: ZV750SY

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

ZV750

GE Monogram ®

Installation

Instructions

36" Vent Hood

Model

ZV750

gefi_re you begin--Read these instructions completely and carefldly.

IMPORTANT: Save these instructions for local inspector's use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these instructions with the (;onsmner.

NOTE TO CONSUMER: Keep these instructions with yore _ Use and (_are Book t()i"

fllture reference.

_!lW'.l;tL'lh'[ell This appliance must be properly grounded. See "Electrical Supply", page 4. i

If wm have questions concerning the installa-

tion of this product, call the GE Answer

Center °' Consmner Intormation Service at

800.626.9000, 94 horn's a day, 7 days a week.

If wm received a damaged vent hood, you

should contact yore" dealer.

CAUTION!

Due to the weight and size of these vent hoods

and to reduce the risk of personal ii_jury or

damage to the product, T_VO PEOPLE ARE

REQUIRED FOR PROPER INSTALLATION.

WARNING!

To reduce the risk of fire or electric shock, do

not use this range hood with any external

solid-state speed control device. Any such

alteration fl'om original thctory wiring could

result in damage to the trait ai'ld/or create an

electrical safety hazard.

To reduce the risk of fire and to properly

exhaust aiI; be sm'e to duct air outdoors. Do

not vent exhaust air into spaces within walls or

ceilings or into attics, crawl spaces or garages.

_\:ARNING: TO REDUCE THE RISK OF FIRE,

USE ONINMETAL DUCT_VORK.

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY TO PERSONS,

OBSERVE THE FOI_LOWING:

A. Use this trait only in the rammer intended

bv the mamlthcturer. If you have arJy q ues-

tions, contact the mamffacturer.

B. Beti)re servicing or cleaning trait, switch

power oil at service panel and lock service

panel to prevent power fl'om being switched

on accidentally. If the service panel cam_ot be

locked, thsten a tag or prominent warning

label to the panel.

For general ventilating use only. Do not use

to exhaust hazardous or explosive materials

and vapors.

Installation work and electrical wiring must be

done by qualified person (s). In accordance

with all applicable codes and standards

including fire-rated construction.

Sufficient air is needed for proper combustion

and exhausting of gases through the flue

(chimney) of tirol burning equipment to

prevent back drafting. Follow the heating

eq uipm ent manuthcturer's guideline and

satiety standards such as those published bv the

National Fire Protection Association (NFPA),

and the American Society for Heating, Refl'ig-

eration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

Con_n_

Design Information

Models available .................................................................................................................................. 3

Optional Accessories ........................................................................................................................... 3

Product Dimensions & Clearances .................................................................................................... 3

Advance Plmming ............................................................................................................................... 4

Electrical Supply .................................................................................................................................. 4

Installation Preparation

Duct Fittings ....................................................................................................................................... 5

Tools and Materials Required ............................................................................................................ 6

Step 1: Remove the packaging ........................................................................................................... 6

Installation

Step 2: Check Installation Hardware ................................................................................................. 7

Step 3: Mount Template ..................................................................................................................... 7

Step 4: Install Motmting Bracket ....................................................................................................... 8

Step 5: Install the Hood ...................................................................................................................... 8

Step 6: Install Duct Bracket ................................................................................................................. 9

Step 7: Comaect Ductwork ................................................................................................................ 10

Step 8: Cmmect Electrical ................................................................................................................. 10

Step 9: Install Decorative Duct Cover. .............................................................................................. 10

Step 10: Install Filters ........................................................................................................................ 11

Step 11 : Finalize Installation ............................................................................................................. 11

Design hdbrmation

36" Ve_t Hood

Model

Available

Optional

Accessories

Model

ZV750

This xent hood is designed to be used in

xented installations.

A decorative duct coxer is proxided to coxer

the duct fl'on_ the top of the hood to an S ti.

or 9 ft. ceiling.

Model

ZX 10SY

An optional stainless steel duct cover is

available for 9 ft. to 10 ft. ceiling installations.

(The supplied duct cover is sized to reach 8 It.

to 9 ft. ceilings.) Oi'der the optional duct

cover at the same time as the vent hood and

have on site befi)re installation.

Product

Dimensions

& Clea" ances

[

o II

L o

Tile xent hood m ust be installed 24" rain. and 30" max.

aboxe tile cooking sm'face. 25-1/2" is recommended to ]_

insm'e that tile duct coxer meets tile ceiling. The cooking _ _-_

surthce should be at least 36 aboxe tile floor. Installation

will be easier if tile xeilt hood is installed before tile

_ meig_t

range or cooktop and comatertop is installed, to Ceiling

21-5/8"

<=> "26-1/4" for 8 ft. ceiling

38-1/4" for 9 ft. ceiling

"25-1/2" Recommended 38-1/4" to 50-1/4" for 9ft. to

10ft. ceiling usingoptional

accessoryZXlOSYDuct Cover

36"Min.

*The distance betweenthe cooking surfaceandthe bottom of the

hoodmust beat least24" and upto 30". The25-1/2"

recommendedinstallation height, abovethe standard 36"

countertop, will insure duct coverfit to the ceiling.

Design Infi)rmation

36" ge_t Hood

Advance

Plannin, g

Ductwork

• Determine tile exact location of tile vent hood.

• Plan tile route for venting exhaust to tile

outdoors.

• Use tile shortest and straightest duct route

possible. For satistactory perflwmance, duct

run should not exceed 100 feet equivalent

length tot any duct configm_ations.

• Refer to "Duct Fittings" chart to compute tile

maxim mn permissable length tot duct rims to

tile outdoors.

• Install a wall cap with damper or roof cap at

tile exterior opening.

Electrical

Supply

Warning, for

Personal

Safety:

Reillove house

fllse or open

circuit breaker betore

begimfing installation.

Do not IlSe aI] extensi(m

cord or adapter plug with

this appliance. Follow

National electrical codes

or prevailing local codes

and ordinances.

Electrical supply

This vent hood must be supplied with 120V,

60Hz., and comaected to an individual, properly

gro/mded branch circuit, protected bv a 15 o1"

90 ampere circuit breaker or time delay fllse.

• Wiring illtlSt be 2 wire with grotmd.

• If tile electrical supply does not meet tile

above requirements, call a licensed electrician

before proceeding.

• Route wiring as close to tile installation

location as possible, in tile ceiling or soffit.

• Cmmect tile wiring to tile house wiring in

accordance with local codes.

Grounding Instruction

Tile grounding conductor must be cmmected to

a gro/md metal, permanent wiring system, or an

equipment-gro/mding terminal or lead on tile

hood.

Warning: Tile improper comaec-

tion of tile equipmerJt-ground-

ing conductor can result in a

risk of electric shock. Check with

a qualified electrician or service

representative if you are in doubt whether

tile appliance is properly gro/mded.

Installation Preparation

36" l,'e_H Hood

Dztct

Use this chart to

conlpute I11axilIl tlI/l

permissable lengths

I_i)I"duct I'/lI]S to

outdoors.

Total

Equivalent Quantity Equivalent

Duct Piece Dimensions i,ength* Used I,ength

Round, 1 tL

straight (per tiler

length)

3-1/4" x 10" 1 ti.

straight (pet" toot

length)

90° elbow 15 ft.

42)° elbow 9 ft.

3-1/4" x 1()"

90._elbow 15 il.

3-1/4" x 10"

45° elbow 9 ft.

3-1/4" x 10"

90'_flat elbow 20 ft.

_ 6" round to

3-1/4" x 10" or

3- 4 x 24 trmsition 1 ft.

3-1/4" x 10"

to 6" round transition 5 ft.

_,, )_ 6" round to

3-1/4" x ll)"

tr msition 9()_ elbow 5 ft.

3-1/4" x 10" to 6" round

tr msition 90 ° elbow l 5 ti.

Note: Donotexceedmaximum

permissahleequivalentlengths!

Maximum ductlength:

100foot for rangehoods.

Flexible ducting:

If flexible metal

ducting is ttsed, all

tile equivalent teet

values in tile table

should be doubled.

Tile flexible metal

duct should be

straight and smooth

and extended as

much as possible.

Do NOT use flexible

plastic ducting.

Note: Anyhomeventilation

system,suchasaventilation

hoed,mayinterrupttheproper

flow ofcombustionairand

exhaustrequiredbyfireplaces,

gasfurnaces,gaswater I_eaters

andothernaturallyvented

systems.To mMmizethechance F>

of interruptionofsuchnaturally

ventedsystems,follow theheating

equipmentmanufacturer's

guidelinesandsafeS/standards

suchasthosepublishedbyNFPA

andASHRAE.

R,.)ut'_d

wall cap

with d re]per 30 ft.

_ 3-1/4" x 10" wall cap

]dth d unper 30 fl.

Round

roof cap 26 ft.

Round

roof vent 24 ft.

*Actual length of straight duct plus duct fitting Total Duct Run

equivalent. Equivalentlength of duct pieces are based

onactual tests conducted by GEEvaluation Engineer-

ing and reflect requirements for good venting

performance with any ventilation hood.

Installation Preparation

36" V_,_I Hood

7bots &

Materials

Required

(not s,])Jg@d)

• Tape measure

• I0aife

• Spirit level

• Wire cutter

• Wire stripper

• _vVire nuts

• Electric drill and appropriate bits

• Phillips screwdriver

• Flat blade screwdriver

• Hanlnler

• Pliers

• Salety glasses

• Tape to mount mmplate

• Gloves to protect against sharp edges

• 12(W 60Hz. 15 or 20 _Mnp, 2 wire with

ground. Properly grounded branch circuit.

• Strain relief for jun ctinn box.

• 6" rotmd metal duct work.

The vent hood is shipped secured to a shipping

board with 4 screws.

• Remove the duct cover, parts box and styro-

ti:mm packaging.

• I,ifl the hood ()tit of the box, using hand grips

on both sides of tile shipping hoard.

• Remove and properly discard the plastic

wrapping.

• Locate and renlove 2 screws at the top of the

assembly and 2 screws inside the hood behind

the filter guides on the lett and right sides.

Discard the shipping board.

• Relnove.jullctioI_ box cover.

• Rein ore knockout tl"om j unction box.

• Install strain relief onto jui_ctioia box.

Junction

Knockout_

Mountin

Screw

/Mounting

Screw

ShippingBoard

Screw

0ard

Installation

36" Ve_t Hood

(/heck

hl,stallation

Hardware

s'3

Ductwork,

WMng,

Hood

Attachment

Locations

Locate the hardware accessory box packed

with range hood and check contents.

Wall

Fasteners

2 Mounting

@ Brackets

_, 2PhillipsHeadScrews

UtilityBarswith Screws 3 Filters

2Large

FlatWashers

Wood

Screws

Decorative

Duct

Cover

Wall Mount Template

To determine ductwork locations:

• Locate the template packed with the litera-

ttlre.

• Determine the exact installation location.

-Measm'e 36" fl'om the floor to the top of

the cooking stlrfhce. Add 25-1/2" recom-

mei_ded space fl'om the cooking sui'filce to

bottom of hood. Mark that location.

-Use a level to draw a straight pencil line on

the wall.

-Tape the template in position along the

penciled line. CHECK TO BE SURE

TEMPLATE IS LEVEl.

• Measure fi'oln the peak of the hood to the

ceiling as indicated. The dilnei_sioi_ should

be:

-26-1/4" to 38-1/4" for 8 ft. to 9 fi. ceilings.

-38-1/4" to 50-1/4" for 9 ft. to lO fL ceilings

this installation requires ZX 10SY accessory

(hlct cover.

CEILING DUCTING

If ductwork will vent straight up to the ceiling:

• Llse a level to draw a line straight up, fl'om

the centerline on the template to the ceiling.

• Measm'e 3-1/2" from the back wall to the

centerline of a 6-1/2" dia. hole on the

ceiling.

Note: Ifdrywallisnotpresent,adddrywallthicknesstothe

3-1/2"dimension.

31/2"

CenterlineT(

VENTDUCTING

6-1/2" Dia.Hole,

6" Min.Above

BracketLocation

WALL DUCTING

If ductwork will vent to the rear:

• Use the level to draw a line straight up fl'om

the cei_terline on the telnplate.

• Measure at least 6" above the bracket location

shown on the template to the centerline of

the 6-1/2" dia. duct hole. (Hole may need to

be elongated tor duct elbow.)

HOUSE WIRING LOCATION:

• The junction box is located on the top of the

hood, at the fl'ont right side.

• Route house wiring as close to the installation

location as possible; through the ceiling,

soltit or back wall. Wiring should enter at

least 4" above the bracket on the right side.

Installation

36" Ve_t Hood

2 e_

hi, stall

Mounting

Brackets

Whenever possible, the vent hood should be

secured to wall studs.

*With the template taped in place, use a

punch to mark all mounting screw locations.

• Drill 1/8" pilot holes at tile 6 punched

locations.

• Remove tile template.

• Enlarge holes that did not enter studs to

3/8" and tap anchors tor wall tasteners into

tile holes.

-Drive screws into tile tasteners to allow

anchors to expand against tile wall material.

Remove tile screws for final installation.

• Secure tile mounting brackets to tile wall

studs with wood screws provided.

-For hollow walls, secure tile mounting

brackets through tile anchors.

Note: Screws'W' and"B"arepre-assembbdontothebrackets.Do

notremovethesescrews.

Install

the Hood

Place tile hood on tile brackets and slide left

to right to align with rectangular slots at tile

top.

• At!just the installation height by tightening

or loosening tile screws "A" at tile bottom of

the brackets.

• Align tile hood lower mounting holes with

pilot holes in tile wall.

• Using two large flat washers (supplied),

install wood screws or wall tastener screws,

loosely, into lower mounting holes. Do not

tighten.

• Level tile hood by tightening or loosening

tile screws "A" located on tile bottom inount-

ing brackets.

• Tighten tile lower mounting screws.

• Tighten screws "B" located at tile top of tile

mounting bracket against tile hood to clamp

tile position. Do not overtighteu screws.

Screws"B"

ToSecureHood

ToWall

-Leveland

Height

Adjustment

Screws'W'

Lower

MountingScrews

Installation

36" Ve_H Hood

Install Duct

Bracket

(/br vertical exhau,sO

• Install the 2 small screws into the sides of the

duct bracket. Remoxe the scre_s. This will

insm'e ease of final installation.

• Temporarily install a piece of 6" duct cut to

length bet_een the hood outlet and the

ductwork at the ceiling.

• Position the upper duct bracket behind the

duct and against the wall and ceiling.

• Llse a level to check that duct is x ertical and

duct bracket is centered.

• Mark the 4 screw locations of the bracket.

• Remoxe the bracket and temporary duct

section.

• Drill 1/8" pilot holes in marked bracket

location.

• If pilot holes do not enter studs, enlarge the

holes 3/8" and install _all thstener anchors,

Drixe screws into the

thsteners to allow anchors

to expand against the _all

material, Remox e the _"

scre_ s,

• Secure the bracket to the

ceiling and wall with wood

screws ai]d/or _all

fasteI] er screws,

Duct

Work

_teBA

Install Duct

Bracket

(/br ho)'izo_?lal exhau,sO

The upper duct bracket should be installed

against the ceiling. This bracket will hold the

decorative duct cover in place at the top.

• Install the 2 small screws into the sides of the

duct bracket, Remove the screws, This will

insm'e ease of final installation.

• Position the bracket against the wall and

ceiling. (:enter the bracket using marked

centerline of the hood,

• Use a pencil to mark the bracket location

along its outside edges,

• Temporarily place the decorative duct cover

on top of the hood and extend the im]er

portion to meet the ceiling,

• The duct cover should be level and align with

marks for bracket,

• Rein ove the duct cover,

• Place bracket against marked location and

mark the 4 screw locations,

• Drill 1/8" pilot holes in marked location,

• If pilot holes do not enter studs, enlarge the

holes 3/8" and install wall thstener anchors,

Drive screws into the thsteners to allow

anchors to expand against the wall material,

Remove the screws.

• Secure the bracket to the ceiling and wall

with wood screws and/or wall thstei]er

screws.

Installation

36" Ve_t Hood

Connect

Ductwork

Do not use sheet metal

screws at hood flange

connection, Doing so will prevent proper

damper operation, Seal connection with

tape only.

• Install ductw()rk, making com_ections in

direction of airflow as illustrated.

• Secure joints in ducrwork with sheetm etal

screws.

• Wrap all duct joints with duct tape fin.

airtight seal,

Duct Tape

Over Seam

and Screw _i

Screw

AirFlow

Step 8

Connect

Electrical

Verify that power is turned off at the source.

If house wiring is not 2-wire with a

ground wire, a ground must be

provided by the installer.

When house wiring is aluminum,

be sure to use U.L. approved anti-

oxidant compound and alumi-

ntlul-to-copper connectors.

• Insert house wiring through strain relief and

tighten,

• Connect white leads to branch circuit white

lead,

• Connect black leads to branch circuit black

lead,

• Connect green/yellow leads to branch

circuit green or bare ground lead,

• Secure all connections with wire nuts on

each electrical connector,

• Push wires into junction box and replace

cover. Be sure wires are not pinched.

Step 9

lnstaU

Decorative

Duct Cover

and

Utility

Bars

Mounting Screws

Notches

Place tile decorative duct cover on top of tile

hood,

• Insert tile lower portion ot tile duct cover

into the impression on the top of the hood,

• Extend the inner duct upwards to meet the

ceiling and bracket,

• Secure the duct cover to the bracket with the

2 small Phillips screws provided,

• Install the side utility bars as shown with

screws provided.

Install Optional ZX10SY Duct Cover

• Separate tile supplied duct cover into pieces.

Discard tile upper (or imaer) section.

• Insert tile new ZX10SYduct cover into tile

original lower section, Be sure that tile new

longer section is inside tile shorter original

section. Tile notches will be at tile bottom

and tile screw holes at tile top as ilh|strated.

• F(>llow tile saule procedtlres shown above to

install tile new duct cover.

Installation

36 _' Ve_l Hood

hl,stall Filter:s

• Remove protective film on filters.

• Tip the filter into the lower slots at the rear

of the opening, lift the filter and pull the

knob fin'ward until the filter rests on the

slots.

• To relnove the filters, grasp the knob and

push the filter towards the rear and tilt

downwards.

Finafize

Installation

• Remove protective film covering the control

panel on the fl'ont thee of the hood and anv

remaining packaging materials.

• Reter to the Use and Care book fi)r

operating instructions.

Monogram:

General Electric Company

Louisville, KY40225

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

Mom_o,ral, inoduct or s_,rvic_s call (;E A _z_w_rC_,llle__'

_o_l_ume_ D@_matio_z se_vi_ e at 800.626.2000 a_9'

Zime, day or _zigfiZ.

l,). Mo_og'_am Io_zd se_vi_ e Dzyou_ an,a, tail

1-800-444-1845.

N()TE: P:oauct implovemenl is _ containing endeavo: _I Gene_ d

Electric¸ Theret_>re. malerials, appearance and _pecificalions are

sul_iecl Io change wilhom nolice

Pub. N_. 49-8990-1

Dwg. N_}. 164D3333P214

(0 2000 GE Appli;m(es

(N.D. 6] 2) 5/00

Printed in Italy

Monogram ZV750SY Installation guide

Brand: Monogram

Model: ZV750SY

Category: Cooker hoods

Type: Installation guide

This manual is also suitable for

ZV750

Download PDF

report

Monogram ZV750SY Installation guide

This manual is also suitable for

Monogram ZV750SY Installation guide

Related papers

Other documents