GE ZDOD240 Installation guide

Category
Fridges
Type
Installation guide

This manual is also suitable for

Installation
Instructions
Outdoor/IndoorRefrigerator
ZDOD240
DesignGuide
With InstallationInstructions
Monogram_
Safety Information
BEFORE YOU BEGIN:
Read these instructions completely and carefully,
IMPORTANT - S.,e_heseinstructions
for local inspector's use.
IMPORTANT - Obse,,e.U_(,,e,.i._
codes and ordinances.
Note to Installer - Be sure to leave these
instHlctions with the Consun_er.
Note to Consumer - Kee I) these instHlctions with
w)ur Owner's Manual tot fllttlre reference.
WARNING - Thisappliancemust be
l)to l)erlx,,grounded . See page 5.
AVERTISSEMENT -
(Yet appareil dolt _tre correctement mis fi la terre.
Consulter page 5.
If you receixed a damaged Outdoor/Indoor
Refrigerator, you should immediatel_ contact your
dealer or builder.
Skill Level - Installation requires basic mechanical
skills. Proper installation is the responsibility of the
installer. Product thilm'e due to improper installation
is not covered under the GE Appliance _,Vm'anty.
WARNINGS:
Use this appliance only fi)r its intended puri)ose.
hmnediately repair or replace electrical service
cords that become ti'aved or damaged.
Ui_i)lug the trait betore cleaning or nmking rei)airs.
Rei)airs should be inade by a qualified service
teclmician,
AVERTISSEMENT :
I1 ne flint utiliser cet appareil que pour l'usage
pour lequel il a _t_ construit.
I1 taut r_parer ou remplacer imm_diatement tout
cordon d'alimentation _lectrique efliloch_ ou
endommag0.
Dgd)rancher le bar ou le rg_ti'ig_ratem" a vin avant
le nettoyage ou toute intervention,
I,es r_parations doivent _tre taites par tm
technicien qualifi_.
For Monogram local service in your area, call
1.800.444.1845
For Monogram service in Cmmda, call
1.888.880.3030
For Monogram Parts and Accessories, call
1.800.626.2002.
www. monogrmn.com
KEY EJECTING LOCK
(NOTE: Two kms are included.)
Kee I) the ke)s out of reach of children and awa)
from the refrigerator in a sate and secure place.
The ke) for the spring-loaded lock is automatically
eiected. The key will not remain in the lock while
the door is opened or closed.
r-^,.,,.,UTION: geiore closing the door, make sure
the lock pin does not protrude beyond the top of the
dora, to prevent potential damage to the cover or cabinetry.
ATTENTION : Axantde re,ermerla p,,rte,
assurezwous que le dispositit de retenue ne d_passe pas le
haut de la porte, afin d'&'iter d'endommager le couvercle
OU l'a rllloire.
2
Important Information
CONTENTS
ImportantInformation
Caringfor YourStainless Steel ......................3
Tools,Hardware ...............................................3
DesignGuide
The Installation Space....................................4
Product Clearances and Location
Requirements ...................................................4
Preparation for Built-In Under-Counter
Installations Only .............................................4
Installation Instructions
Grounding the Product ................................... 5
Step 1, Remove Packaging ............................ 6
Step 2, Leveling ................................................ 6
Step 3, Connect Power ................................... 6
Step 4, Slide Product into Cutout .................. 6
Step 5, Set Temperature Controls ................. 6
Staining Wood Drawer Fronts ....................... 7
CARING FOR YOUR STAINLESS
STEEL
geff_re installation or first use, we strongly advise you
polish tile stainless steel exterior and handle with a
commercially awfilable stainless steel cleaner such as
Stainless Steel Magic TM. To preserve and protect tile
fine finish we also strongly advise that you apply
stainless steel cleaner monthly.
All stainless steel can be damaged by tile following
substances. Care must be taken not to allow these
substances to come in contact with wmr Outdoor/
Indoor Refrigerator. If anv of these do get
on w)ur unit wash and clean tile trait immediately
(see the Care and Cleaning section in the Owner's
Manual).
Battery Acid
Pool Chemicals (such as Chlorine and Bromine)
I,awn Fertilizer
Ice Melting Salts
Creosole
Iodine
Pickling Juice
Urine
The following naturally occurring materials can
cause danlage to tile stainless steel finish. If any of
these substances do get on your unit wash and clean
tile trait immediately (see tile Care and Cleaning
section in tile Owner's Manual).
Bird Droppings
Tree Sap
Sea _,Vater
TOOLS REQUIRED
Hea\T-duty work gloves
#9 Phillips screwdriver (fi_r built-in installations only)
A(!justable wrench
PARTS SUPPLIED
Two keys
3
Design Guide
THE INSTALLATION SPACE
23-3/4"
34-1/2"
NOTE:
Handleand
handlestandoff
depthis2-3/4"
Free-Standing- Usecanopytop Built-In - Removecanopytop
(if needed)
Choose the location:
This product has been designed as a free-standing
unit; however, if desired, it may also be built-in.
These products may be closed ill on the top and
three sides as long _ls tile fl'ont is unobstructed fl>i"
air circulation and proper access to tile door.
Do not operate these products where the temllerature
will go below 45°F (7°C) or above 190°F (49°C).
Unit must be installed on a stiucturallv sound and
level surfilce strong enough to support a fldly loaded
refligeratm; or approx. 250 lbs.
24"
The cutout depth should be 24"
Tile cutout dimensions shown allow for a fidl door
swing and access to the pull-out racks when installed
ill standard 24" deep cabinets.
Tile Outdoor/Indoor Refrigerator can be installed
fl'ee-standing,
If installing between frameless cabinets, a l/2" wide
filler strip or side panel may be required on tile
hinge side, The filler strip will act as a spacer between
tile case and a(!jacent cabinet door swing. Tile width
of the opening must include the filler panels.
NOTE: Ill a standard 24" opening, the door will
protrude l-I/2" fin'ward of tile surrounding cabinets.
Additional Specifications
A 120 volt 60Hz., 15 or 20 amp power supply is
required. All individual properly grounded branch
circuit or circuit breaker is recomn]ended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall as shown, Electrical must
be located on rear wall as shown. THIS PRODUCT
MUST BE CONNECTED TO A POWER SOURCE
WITH GROUND FAULT CIRCUIT INTERRUPTER
(GFCI) PROTECTION WHEN INSTALLED IN AN
OUTDOOR LOCATION. LOCAL CODES MAY
REQUIRE A SEPARATE CIRCUIT.
PRODUCT CLEARANCES AND
LOCATION REQUIREMENTS
Tile Outdoor/Indoor Refligerator is factory set fin"
a l l 0° door swing.
When installed in a corner:
Allow 5-1/4" rain. clearance on tile hinge side tor tile
90 ° door swing and to allow racks to slide out.
Allow 15" n]ininmln clearance on tile hinge side tor
a fldl 110 ° door swing.
Test tile door swing. Carefull) open and close tile (tooi:
Tile door should not rtlb or catch on ac!jacent cabinet U.
Ac!iust if the door makes contact with cabinet U.
15"Minimum
toWall
, 110° [
Door
Swing
i
I
'\,, \\\\
110° .. ,
Swing!;
\ ii 23-5/8"
- _ 4,-L; -
5-1/4" Minimum
to Wall
4
PREPARATION FOR BUILT-IN
UNDER-COUNTER INSTALLATIONS
ONLY
Tile top canopy may be removed when installing under
a COtlntertol).
I/elnove tile three screws ti'oln tile back of tile top
canoI)y CA).
Using heavy-du V work gloves, lift up on tile top
canopy back (B) and slide it torward until it unlatches
fl'oln the unit ((:).
iJfl tile top canopy up and ott' of tile tlnit.
NOTE: Kee I) the top canopy and screws tot future
free-standing installations.
NOTE: When installing the unit ill a flee-standing
configuration, tile top canopy inust be leli ill place.
If replacing the top canopy inake sure the three latches
ill tile fl'ont slide into tile fl'ont lip of tile canopy betore
pushing file canopy to the rear of the unit.
(B)
CA)
CAUTION:
Undersideedges
of the stainless (C)
steelcanopytop
maybesharp.
Wearheavy-duty
workgloveswhen
movingthe top.
Installation Instructions
GROUNDING THE OUTDOOR/
INDOOR REFRIGERATOR
WARNING -
THIS PRODUCT MUST BE
CONNECTED TO A POWER
SOURCE WITH GROUND
FAULT CIRCUIT INTERRUPT
(GFCI) PROTECTION WHEN
INSTALLED IN AN OUTDOOR
LOCATION. LOCAL CODES MAY
REQUIRE A SEPARATE CIRCUIT,
AVERTISSEMENT -
CE PRODUIT DOlT I_TRE
CONNECTE A UNE SOURCE
D'ALIMENTATION A
DISJONCTEUR DE FUITE
A LA TERRE, EN CAS
D'INSTALLATION EN PLEIN-AIR.
LES RI_GLEMENTATIONS
LOCALES PEUVENT EXIGER
UN CIRCUIT DISTINCT.
IF YOU ARE UNCERTAIN ABOUT THE GFCI
PROTECTION ON THE POWER SOURCE
TO WHICH YOU ARE CONNECTING THIS
APPLIANCE, PLEASE CONTACT A PROFESSIONAL
ELECTRICIAN FOR VERIFICATION.
GROUNDING THE OUTDOOR/
INDOOR REFRIGERATOR (CONT.)
IMPORTANT: PLEASE READ CAREFULLY.
FOR PERSONAL SAFETY, THIS APPLIANCE
MUST BE PROPERLY GROUNDED.
The power cord of this appliance is
equipped with a 3-prong (grounding)
plug which mates with a standard 3-prong
(grotmding) wall receptacle to minimize
the possibility of electric shock hazard
from this appliance. Have the wall outlet
and circuit checked by a qualified electrician
to make sm'e the outlet is properly grotmded.
Where a standard 2-prong wall outlet is encotmtered,
it is yore" personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT
OR P,EMOVE THE THIRD (GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER
PI.UG TO CONNECT THE
REFRIGERATOR TO A 2-PRONG
OUTI,ET.
DO NOT USE AN EXTENSION
CORD WITH THIS APPI,IANCE.
DO NOT PI,ACE THE UNIT IN STANDING
_4;_TER OR AI,I,OW THE POWER CORD TO
BE IMMERSED.
5
Installation Instructions
ISTEP 11 REMOVE PACKAGING
]_einove corner blocks and flmm drawer stops.
Remove all packing material, tape and protective
plastic coverings.
CAUTION: s,,,.u (,bje(-ts area choke hazard
fl)r children. Remove and discard any parts not used.
ATTENTION : petits.bietspe.,e.t
_trangler les enfimts. 11 fautjeter toutes les pi_ces qui
ne sont pas utilis_es.
ISTEP 21 LEVEL
Use an a(!justable wrench to tm'n and raise or lower
the leveling legs.
Measure floor to co/mtertop height inside tile
opening. Ac!j ust leveling legs until the l)ro(htct is
approximately 1/8" less than co/mtertop height.
TurnRightto Lower
TurnLefttoRaise
INSTALLATION TIP:
Measm'e floor to underside of countertop inside tile
opening.
If tile room floor is higher than tile floor inside tile
opening, a(!just the rear leveling legs to approximately
1/8" less than the opening height, Screw fl'ont leveling
legs all the way in to shorten the height at the fl'ont,
This will allow you to slightly tip the refit into the
opening. Once tile trait is in tile correct position, tile
fl'ont legs can be a(!justed to level tile product.
ISTEP 31 CONNECT POWER
If the refl'igerator is used outdoing, plug tile power
cord into a GFCI receptacle.
Check to make sm'e power is on by opening tile door
to see if interior light turns on.
The interior tim rims at all times except when the
door is open. See the the Owner's Manual tor fl,rther
explanation.
ISTEP 41 SLIDE PRODUCT INTO
THE CUTOUT
CAUTION: D,,t,,tti.ltsh.g.it,sttiledoor
with yore" knees. Do not push or lift tile trait bv tile
door handle. Damage may occur!
ATTENTION : Ne i)oussezjamais la porte
avec vos genoux. Ne poussezjamais votre appareil ou ne
le soulevezjamais par la poign_e de porte. Vous pouvez
1'endotlltllager.
Open the door and gently push the unit back into the
opening with wmr hands against the sides. Be carefltl
not to entangle power cord.
In a standard 24" opening, tile door will protrude
l-I/2" fi)rward of tile surrounding cabinets.
Check again to be sure the trait is level.
If tile trait is installed trader a countertop, a@tst tile
leveling legs until the trait is resting firmly against
tile bottom of tile co/mtertop.
If aligmnent with a(!jacent cabinetry is an issue,
use a shim to secure the unit against the tmderside
of tile co/mtertop.
Test the door swing. Carefidly open and close the
door. Tile door should not mb or catch on a(!iacent
cabinett T, Noti{}' the installer if the door makes
contact with cabinetry,
ISTEP 51 SET TEMPERATURE
CONTROLS
Tile temperature controls are preset. Reter to tile
Owner's Manual fi)r more inflmnation. Allow 12-24
hours fl)r temperature to stabilize.
NOTE: The Outdoor/Indoor Refl'igerator operates
very quietly. You may not notice the unit t mining, and
when first installed, the rims and motor may not come
on immediately--this is normal. If the displayis lit
and the light is working, the unit is operating.
6
Installation Instructions
STAINING WOOD DRAWER FRONTS
The drawer fronts are unfinished cherry wood. During
use, oil fl'om hands may accumulate and stain the wood.
The drawer fl'onts may be stained and sealed to match
a(!iacent cabinetry.
Apply the stain and sealer according to the
manufhcttn'er's instructions. To avoid unpleasant odor;
keep the door open to ventilate and allow the stain/
sealer to dry completely before using the product.
NOTE:While performing installations described in this book,
safety glasses or goggles should be worn.
®
I_or Mo_wgmm loc_d _rvic_J i_ )our are., c_dl
) 5
l. 800.444. l,_4 .
NOTE: Producl improvem( nt is a cominuing ( ndeavor
at General Electlq(. Th¢ v,:d'or¢, matt vials, app(arance
an([ specificalions are sul)ject Io change withoul llOliC(>.
Pub.No.31-51542-1 ]
]
PartNo. 197D5893P001
02-04JR
PrintedihSlovenia
Monogram:
GEConsumor & Industrial
Louisvil]e, KY40225
@2004GE Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

GE ZDOD240 Installation guide

Category
Fridges
Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI