Altronix SMP3PMP4 Installation guide
- Category
- Power adapters & inverters
- Type
- Installation guide
This manual is also suitable for
SMP3CTXseries
-
1
-
Power Supply Voltage Output Specifications: *
Output VDC Switch Position Max. Load DC
12VDC
SW1 - Closed
(F
ig. 1b, pg. 3)
2.5 amp
24VDC SW1 - Open
(Fig. 1b, pg. 3) 2.5 amp
*Specified at 25˚ C ambient.
Installation Instructions:
W
iring methods shall be in accordance with the National Electrical Code/NFPA 70/NFPA 72/ANSI, and with all local
codes and authorities having jurisdiction. Product is intended for indoor use only.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lo
w
er holes and install the three f
asteners. Place the enclosure’
s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws
(Enclosure Dimensions, pg. 4).
Secure enclosure to earth ground.
2.
Set SW1 on the po
w
er suppl
y board to the desired DC output v
oltage
(P
o
w
er Suppl
y
V
olta
ge Output Specification Chart)
.
SMP3CTX Series Power Supply Configuration Reference Chart:
Overview:
These units will con
vert a 115VAC or 230VAC, 50/60Hz input, into a regulated 12VDC or 24VDC output up 2.5 amp of
continuous load current (see specifications).
Specifications:
• Universal 115/230VAC input.
• Maximum charge current .5 amp.
• Filtered and electronically re
gulated outputs.
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when
AC fails (zero voltage drop).
• AC input and DC output LED indicators.
• Short circuit and thermal overload protection.
• Complete with power supply, power distribution module
(w
hen applicable), enclosure, cam lock & battery leads.
• Power on-off switch.
Supervised models only:
• AC fail supervision (form "C" contacts).
• Low battery supervision (form "C" contacts).
SMP3CTX Series - Installation Guide
SMP3CTX - 1 - - - - .65 / .35 2.5
SMP3PMCTX - 1 - - - x .65 / .35 2.5
SMP3PMCTXX - 1 - - - x .65 / .35 2.5
SMP3PMP4 PD4 4 x - 3.5 x .65 / .35 2.5
SMP3PMP4CB PD4CB 4 - x 2.5 x .65 / .35 2.5
SMP3PMP8 PD8 8 x - 3.5 x .65 / .35 2.5
SMP3PMP8CB PD8CB 8 - x 2.5 x .65 / .35 2.5
SMP3PMP16 PD16W 16
x - 3.5 x .65 / .35 2.5
SMP3PMP16CB PD16WCB 16 - x 2.5 x .65 / .35 2.5
Altronix
Model Number
Accessory Power
Distribution
Module(s)
Number of Outputs
Fused Outputs
PTC Outputs
Individual Output
Rating (amp)
115VAC / 230VAC
Input Current (amp)
12/24VDC Total
Output Current (amp)
Supervised
- 2- SMP3CTXseries
3
. Connect AC power to terminals marked [L & N], connect ground to terminal marked [G] (if used).
Use 18 AWG or larger for all power connections (Battery, DC output).
U
se 22 AWG to 18 AWG for power limited circuits (AC Fail/Low Battery reporting).
4. Measure output voltage before connecting devices. This helps avoid potential damage.
5. Connect devices to be powered:
a. For Power Supply Board connect to terminals marked [– DC +].
b. For Power Distribution Module(s) connect devices to be powered to terminal pairs 1 to 4 marked
[1P & 1N thru 4P & 4N]
(Fig. 2, pg. 3), 1 to 8 marked [1P & 1N thru 8P & 8N] (Fig. 3, pg. 3), or 1 to 16 marked
[1P & 1N thru 16P & 16N]
(Fig. 4, pg. 3) carefully observing correct polarity.
*Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board. When servicing the unit,
AC mains should be removed.
6. When using stand-by batteries, they must be lead acid or gel type. Connect battery to terminals marked [– BAT +]
(battery leads included). Use two (2) 12VDC batteries connected in series for 24VDC operation.
Note: When batteries are not used a loss of AC will result in the loss of output voltage.
For supervised models only:
7. Connect appropriate signaling notification devices to AC Fail & Low Bat supervisory relay outputs
marked [NC, C, NO]
(Fig. 1a, pg. 3).
LED Diagnostics:
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF
Loss of AC, Stand-by battery supplying power.
OFF
ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Terminal Identification:
Terminal Function/Description
Legend
L, G, N Connect 115VAC/230VAC to these terminals:
L to Hot, N to Neutral, G to g
round (if used).
– DC + 12VDC / 24VDC @ 2.5 amp continuous non-power limited output.
*AC FAIL Indicates loss of AC power, e.g. connect to audible device or alarm
NC, C, NO
panel. Relay normally energized when AC power is present.
Contact rating 1 amp @ 120VAC / 28VDC.
*Low Battery Indicates low battery condition, e.g. connect to alarm panel.
NC, C, NO Relay normally energized when DC power is present.
Contact rating 1 amp @ 120VAC / 28VDC
Low battery threshold:
12VDC output threshold set @ appro
ximately 10.5VDC,
24VDC output threshold set @ approximately 21VDC.
– BAT + Stand-by battery connections. Maximum charge rate .5 amp.
*Note: Supervised models only
PD4/PD4CB/PD8/PD8CB/PD16W/PD16WCB - Power Distribution Module
Terminal Legend Function/
PD4/PD4CB PD8/PD8CB PD16W/PD16WCB Description
1P to 4P 1P to 8P 1P to16P Positive DC power outputs.
1N to 4N
1N to 8N
1N to 16N
Ne
g
ati
v
e DC power outputs.
SMP3CTXseries
-
3
-
L G N
OFF ON
OPEN - 24VDC
CLOSED - 12VDC
5A 250V
Power
Distribution
Module(s)
Power Supply
Board
C
AUTION: De-energize unit prior to servicing.
Green
Lead
Wire
Strap
(from
Enclosure
to Door)
115/230VAC
power
mains
INPUT
CAUTION: When power supply board is set for 12VDC use only one (1) 12VDC
stand-by battery.
12VDC Rechargeable Battery
(
optional)
1
2VDC Rechargeable Battery
(optional)
LOW BAT
NC C NO NC C NO
AC FAIL
LOW BAT
NC C NO NC C NO
AC FAIL
--- BAT + --- DC +
OPEN - 24VDC
CLOSED - 12VDC
INPUT
LED
1P, 2P, 3P, 4P = FUSED OUTPUTS
1N, 2N, 3N, 4N = COMMON OUTPUTS
F1
F1
F2 F3 F4
COMMON POWER OUTPUTS
1P
1N
2P
2N
3P
3N
4P
4N
DC Output to devices
From Power Supply
Board
(Factory Installed)
Used on
PTC Models
N
COMMON POWER OUTPUTS
P
FUSED POWER OUTPUTS
1 2 3 4 5 6 7 8
1
D1
INPUT
R1
LED
DC Output to devices
From Power Supply
Board
(Factory Installed)
ON OFF
SW1
Fig. 1
Fig. 2
Fig. 3
Fig. 1a
Fig. 1b
Power Distribution Module(s):
common
outputs
protected
outputs
P
N
NPS
XFMR Input
12345678
9 10 11 12 13 14 15 16
P
N
3.5A 250V
For continuous protection against risk of fire
replace fuses with same type and rating.
Used on
PTC Models
Fig. 4
- 4- SMP3CTXseries
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
w
eb site: www.altronix.com, e-mail: [email protected], Made in U.S.A.
IISMP3CTX series - Re
v
. 051105
H02J
1
2.230"
1
5.500"
1
.100"
0.910"
1
.100"
0.910"
0.790"
1.100"
1.500"
1.250"
5
.000"
1.250"
1.500"
4.615"
4.615"1.500"
1.750"
1.500"4.615"
4.615"1.500"
1
.750"
4
.500"
4
.500"
1
.250"
1.500"
5
.000"
2.000"
2.000"
1.250"
1.375"
1.125"
Enclosure Dimensions for:
• SMP3PMCTXX
15.5”H x 12.23”W x 4.5”D
Enclosure accommodates up to
two (2) 12VDC/12AH batteries.
Enclosure Dimensions for:
• SMP3CTX
• SMP3PMCTX
• SMP3PMP4
• SMP3PMP4CB
• SMP3PMP8
• SMP3PMP8CB
• SMP3PMP16
• SMP3PMP16CB
13.5”H x 13”W x 3.25”D
Enclosure accommodates up to
two (2) 12VDC/7AH batteries.
Also available to accommodate up to
two (2) 12VDC/12AH batteries
(please contact Altronix).
MEMBER
5.10"
6.5625"
3.25"3.25"
5.10"
5.10"
3.25"
1.00"10.50"1.00"
1.00"
1.00"
1.40"
1.20"
1.40"
1.20"
0.75
"0.75" 11.00"
12.50"
3.25"
0.9375"
0.9375"
1.40" 4.85" 4.85" 1.40"
1.20"
Bottom
Top
RightLeft
-
1
-
2
-
3
-
4
Altronix SMP3PMP4 Installation guide
- Category
- Power adapters & inverters
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Altronix SMP5CT Series Configuration Reference Chart
-
-
Altronix OLS180 Installation guide
-
-
Altronix OLS120 Installation guide
-
-
-
-
Altronix PD8 User manual
-
