Page is loading ...
Overview:
The Altronix SMP7WP is a 12VDC or 24VDC @ 6 amp power supply, mounted in a NEMA 4 Rated outdoor enclosure.
Designed to be mounted outdoors to reduce installation and wiring costs while increasing efficiency and reliability.
Specifications:
Agency Listings:
• CE Approved.
Input:
• Input: 115VAC / 60 Hz., 1.45 amp.
Output:
• 12VDC or 24VDC selectable output.
• 6 amp continuous supply current.
• Filtered and electronically regulated outputs.
• Short circuit and thermal overload protection.
Battery Backup:
• Built-in charger for sealed lead acid or gel type batteries.
• Automatic switch over to stand-by battery when
AC fails (zero voltage drop).
• Maximum charge current .7 amp.
Additonal Features:
• NEMA 4/IP 65 rated enclosure.
• AC input and DC output LED indicators.
• Power ON/OFF switch.
Enclosure Dimensions:
12”H x 8”W x 6”D
Voltage Output Selection Table:
Installation Instructions:
The unit should be installed in accordance with The National Electrical Code and all applicable Local Regulations.
1. Mount unit in desired location. Mark and predrill holes in the wall to line up with the top two keyholes in the
enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s
upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the
enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the two
upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 2).
Secure enclosure to earth ground.
2.
Set SW1 on the po
wer supply board to the desired DC output voltage (Voltage Output Specification Chart).
3. Connect
AC power to terminals marked [L & N], connect ground to terminal marked [G] (if used).
4. Measure output voltage before connecting devices. This helps avoid potential damage.
5. Connect devices to be powered carefully observing correct polarity.
*Note: Power switch is used to disconnect the L (HOT) terminal from the rest of the board.
When servicing the unit, AC mains should be removed.
SMP7WP - High Current Outdoor Power Supply
Fig. 1
CAUTION: De-energize unit prior to servicing. For continued protection against
risk of electric shock and fire hazard replace fuse with the same type and rating
3.5A, 250V. Replace protective cover on the fuse of the power supply board,
before energizing unit.
-- DC +
-- BAT +
DC
AC
L G N
OFF ON
SW1:
24V - OPEN
12V - CLOSED
CAUTION 120VAC:
Do Not Touch
Exposed Metal Parts
Fuse Cover
unswitched
115VAC 60 Hz,
1.45 amp
power mains
Green
Lead
(Ground)
OPEN SWITCH
CLOSED SWITCH
Switch Detail
Output
Voltage
Switch Position
(SW1)
12VDC CLOSED
24VDC OPEN
Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.
Altronix Corp.
140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056
website: www.altronix.com, e-mail: [email protected], Lifetime Warranty, Made in U.S.A.
IISMP7WP - Rev. 061609 F16I
MEMBER
0.75"
0.75"
11.25"
12.00"
10.00"
8.77"
8.00"7.40"
0.50"
2.00"
0
.77"
6.00"
6. When using stand-by batteries, they must be lead acid or gel type. Connect battery to terminals marked [- BAT +]
(battery leads included). Use two (2) 12VDC batteries connected in series for 24VDC operation.
Note: When batteries are not used a loss of AC will result in the loss of output voltage.
LED Diagnostics:
Terminal Identification:
Enclosure Dimensions:
12”H x 8”W x 6”D
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF Loss of AC, Stand-by battery supplying power.
OFF ON No DC output.
OFF OFF Loss of AC. Discharged or no stand-by battery. No DC output.
Terminal Legend Function/Description
L, G, N Connect 115VAC to these terminals: L to Hot, N to Neutral, G to ground (if used).
-- DC + 12VDC or 24VDC @ 6 amp continuous supply current.
-- B AT + Stand-by battery connections. Maximum charge rate 700mA.
/
