Juno JDK8730W User manual

Brand: Juno

Model: JDK8730W

Category: Cooker hoods

Type: User manual

Juno JDK8730W is a versatile and efficient kitchen appliance, designed to effectively remove cooking odors and fumes, and provide optimal lighting for your cooking area. With its dual functionality, it offers the flexibility of both exhaust and recirculation modes, adapting to your specific kitchen setup and ventilation needs.

L 384 Ed. 09/93

Fig. 1

Fig. 2

Montagevorschrift und Gebrauchsanleitung

für die Dunstabzüge

Prescriptions de montage et mode d’emploi de la hotte aspirante

Instruction on mounting and use of the cooker hood

Istruzioni di montaggio e d’uso della cappa aspirante-filtrante

JDK 8730 W, JDK 8730 E

JDK 9730 W, JDK 9730 E

Ø 118

Ø 98

Ø 110

Ø 123

Der Umwelt zuliebe auf

Recycling-Papier gedruckt

Imprimé sur papier recycle

For this instruction manual has

been used recycled paper

Questo libretto è stato

stampato su carta riciclata

Fig. 5

(Ø 2,9 x 13)

G (2,9x13)

Fig. 4

Fig. 3

5x45

Ø5-20

Ø 8

Fig. 6 Fig. 7

F (2,9x9,5)

3,5x16

Fig. 8 Fig. 9

F (2,9x9,5)

2,9x13

Fig. 10

Schalter für die

Leistungsregelung

des Lüfters

Kontroll-

Leuchte

Schalter für die

Beleuchtung

Fig. 11

Hood Description

1) Motor speed button

2) Light button

3) Operating light

4) Exhaust grate

5) Work-light

Use

The hood may be used as follows:

— Exhausting version

— Recycling version

Exhausting version

The air is vented outdoors by a duct which

must be connected to the coupling ring A

(Fig. 1).

For JDK 9730 hood only:

Check if the internal shutters S are opened

before using the hood (Fig. 11).

Choosing the exhausting pipe

The coupling ring A has a diameter of

120mm.

We suggest to use Ø 120 mm exhausting

pipe.

Using the multi-connector C, Ø100, Ø110

and Ø125 mm exhausting pipes can be

used.

Ø 120 mm exhausting pipe: the multi-

connector has not to be fitted.

Ø 125 mm exhausting pipe: insert the

multi-connector on the coupling ring and

remove, using a proper tool, the upper

unused Ø 100 and Ø 110 mm rings of the

multi-connector.

Ø 110 mm exhausting pipe: same

procedure, but removing the Ø 100 mm ring

only.

Ø 100 mm exhausting pipe: apply the

multi-connector on the coupling ring.

Recycling version

The air is filtered through a carbon filter and

recirculated into the room through the grating

on the lower chimney part.

This version is used when there is no exhaust

duct for venting outdoors or when it is

impossible to install one.

To use the hood in this version, proceed as

follows:

— If no carbon filter is supplied with the

hood, ask the technical assistance

service or the manufacturing company

for one and specify the hood model.

— Dismount the metal grease filters

— To install the carbon filter, fit it in the seat

at the back and fasten it at the front with

the two hooks B (Fig. 2).

— Re-fit the metal grease filters.

For JDK 9730 hood only:

Attention! Close the shutters S before using

the hood in this version.

Installation

When installed, the hood must be not less

than 65 cm. above electric burners or 75

cm. above gas or mixed-fuel burners.

(h,Fig.3).

Warning!

— If the hood is run at the same time as a

burner or fireplace that depend on

ambient air (for example gas, Diesel,

coal or wood heaters, water heaters,

etc.) be careful, because the hood, when

it exhausts the air, removes the ambient

air required by the burner or fireplace for

combustion.

— For secure operation and to prevent

discharged gas from coming back in, the

vacuum must not exceed 0,04 mbr.

This may be done by making sure the air

inlet into the room passes through non-

closing openings such as air recycling

wall boxes, doors, windows or with other

technical measures.

—No food must be cooked flambé

underneath the hood.

The use of an unprotected flame is

dangerous for the filters and could cause

fires.

Therefore, never use an open flame

under the hood. When frying foods, never

leave the pan alone because the cooking

oil could flare up.

— The hood must not be connected to fuel

exhaust flues (boilers, heating systems,

water heaters, etc.).

— Please, keep to the provisions of official

directives regarding the question of fume

discharge.

— The manufacturers refuse to accept any

responsibility for damage to the hood or

its catching on fire because of failure to

observe the above instructions.

Suggestions for the installation and

use of the hood

— The horizontal sections of the pipe must

be slanted slightly upwards (about 10%)

to ensure an easy flow of the air outwards.

— The best performance of the unit is

obtained in the external exhaust model

(suction), therefore in the limits of the

possibilities it is advised to use the

external exhaust (suction) type.

— The best performances are obtained with

short pipes (max. 4 m) and with few

curves.

Electric connection

Before completing any connection, make

sure the house voltage corresponds with

the voltage indicated on the label affixed

inside the hood.

The hood is supplied with a standard plug;

connect it to a correspondingly standard

socket. In the case is intended to connect

the appliance permanently to the mains

after having removed the plug supplied,

must be fitted a two-pole switch conforming

to regulations with an opening distance

between contacts of not less than 3mm.

The manufacturers are not liable for any

problems caused by the user’s failure to

observe the above instructions.

Fastening the hood to the wall

(Fig. 4)

— Position the template in the correct

position and make two 8mm diameter

holes and two 12mm diameter holes.

— Fit the two 8mm diameter plugs in the top

holes.

— Fasten the two hooks C in the bottom

holes.

— Hang the hood on the hooks and level it

with the screws D.

— Secure it in place with the two 5x45 mm

screws and 5-20 mm diameter washers

in the top holes. The screws and washers

are standard equipment.

Installing the duct for exhausting

version (Fig. 5-6)

— Fasten the top support E to the wall close

to the ceiling on the perpendicular of the

bottom connections. To do use the two

8mm diameter screws and plugs supplied

as standard equipment.

Insert the plastic mould P on the duct.

— Take the measure between the ceiling

and the hood top, and adjust the duct to

this height. Fasten it with the screws

— Insert the duct with the slots downwards

and fasten it with the two top screws and

the two bottom screws G.

Installing the duct for recycling

version

Perform the same operations described in

the preceding paragraph. With screws

supplied, fasten the air conveyor M inside

the duct (Fig. 9).

Fastening of shelves (optional)

(Fig. 7)

Fasten the four side supports I to the adjacent

cabinets and place the shelf on the supports.

Operation

The hoods JDK 8730 and JDK 9730 are

provided with a motor with several speeds.

For the best performance, we recommend

using the low speeds in normal conditions

and the high speeds in particular cases of

strong odour and vapour concentration.

We recommend starting up the hood a few

minutes before cooking and keeping it

running until all the odours have been

eliminated.

To start the appliance, pull the control panel

downwards for access to the light and motor

switches (fig. 10).

The hood has a microswitch so that once

the motor speed has been selected and the

light switched on, the hood can be started

by simply pulling out the control panel.

When the panel is closed, the hood

switches off.

The control panel can be positioned at the

desired angle to light the cooking area.

Maintenance

Before performing any maintenance

operation, disconnect the hood from the

electricity.

Grease filter

This serves to hold the grease particles in

suspension.

To remove the filter, push it towards

the back of the hood and pull it

downwards (Fig. 8).

To clean, wash it in hot water and

biodegradable detergent or in a dishwasher.

Let dry before reinstalling.

Clean it at least once a month.

Carbon filter

This filter dissolves cooking odours.

It should be changed every 6-8 months in

normal use. Ask the technical assistance

service or manufacturing company for a

new one.

The carbon filter must never be washed.

To remove the carbon filter, push the push-

buttons B inwards and pull the filter

downwards (Fig. 2).

Important

Failure to observe the rules for cleaning the

appliance and changing and cleaning the

filters may cause fires.

Therefore, we recommend observing these

instructions.

Changing the neon light and starter

— Disconnect the hood from the electricity.

— Open the light cover by turning the latches

L (Fig. 8).

— Replace the damaged part with one of

equal rating.

— Before calling for technical service

because the light fails to work, make

sure the components are tightly fastened.

Cleaning

To clean the outside of the hood use a cloth

moistened with denatured alcohol or neutral

liquid detergents. Never use products

containing abrasive.

This appliance meets 87/308 EWG radio

and television noise Standards

Descrizione della cappa

1) Tasto velocità motore

2) Tasto luce

3) Spia di funzionamento

4) Griglia d’aspirazione

5) Illuminazione piano di lavoro

Utilizzazione

Sono possibili le seguenti utilizzazioni della

cappa:

— Versione ad evacuazione esterna

— Versione a riciclo

Versione ad evacuazione esterna

L’aria viene espulsa all’esterno con l’ausilio

di una tubazione da collegare alla flangia A

(Fig. 1).

Per cappa mod. JDK 9730:

Prima di mettere in funzione la cappa,

accertarsi che le serrandine interne S siano

aperte (Fig. 11).

Possibilità di collegamento a tubi di

scarico

Il diametro della flangia A è di 120 mm.

Per lo scarico dei vapori e dei fumi si consiglia

di utilizzare un tubo di scarico di Ø 120 mm.

Con l’uso del multiraccordo C si possono

usare anche tubazioni di Ø 100, 110 e

125mm.

Tubo di scarico di Ø 120 mm: non è

necessario utilizzare il multiraccordo.

Tubo di scarico di Ø 125 mm: inserire il

multiraccordo sulla flangia e togliere,

utilizzando uno strumento idoneo, gli anelli

del multiraccordo di Ø 100 e Ø 110 mm.

Tubo di scarico di Ø 110 mm: stesso

procedimento del precedente, togliendo solo

l’anello del multiraccordo di Ø 100 mm.

Tubo di scarico di Ø 100 mm: applicare il

multiraccordo sulla flangia senza effettuare

alcuna modifica sulla stessa.

Versione a riciclo

L’aria viene filtrata attraverso un filtro al

carbone e riciclata nell’ambiente attraverso

la sgrigliatura posta sul camino.

Si ricorre a questo utilizzo quando non si ha

una tubazione di scarico verso l’esterno o

non è possibile installarla.

Per utilizzarla in questa versione operare

come segue:

— Se la cappa è sprovvista di filtro,

richiederlo al servizio assistenza tecnica

o alla Ditta costruttrice, specificando il

modello dell’apparecchio.

— Per montare il filtro, inserirlo nell’apposita

sede fissarlo anteriormente con i due

agganci B (Fig. 2).

Per cappa mod. JDK 9730:

Attenzione! Prima di mettere in funzione la

cappa, chiedere le serrandine interne S

(Fig. 11).

Installazione

L’apparecchio messo in opera dovrà distare

dal piano di lavoro non meno di cm. 65 nel

caso di fornelli elettrici e cm. 75 nel caso di

fornelli a gas o misti (h - Fig. 3).

Attenzione

— Con il funzionamento contemporaneo di

una cappa ed un bruciatore o focolare

dipendente dall’aria dell’ambiente (come

per esempio apparecchi di riscaldamento

alimentato a gas, nafta, carbone etc...) si

deve fare attenzione, in quanto la cappa,

aspirando, toglie all’ambiente l’aria di cui

il bruciatore o focolare necessita per la

combustione.

—Per un funzionamento sicuro la

depressione non deve superare 0,04

mbar, così si evita la re-aspirazione dei

gas di scarico.

Ciò può essere ottenuto assicurando

l’ingresso dell’aria nell’ambiente

attraverso aperture non chiudibili, quali

Juno JDK8730W User manual

Brand: Juno

Model: JDK8730W

Category: Cooker hoods

Type: User manual

Download PDF

report

in other languages

italiano: Juno JDK8730W Manuale utente

Juno JDK8730W User manual

Juno JDK8730W User manual

in other languages

Related papers

Other documents