Schumacher 00-99-000990-0809 User manual

00-99-000990/0809

READ THE ENTIRE MANUAL BEFORE USING THIS PRODUCT. •

FAILURE TO DO SO CAN RESULT IN SERIOUS INJURY OR DEATH.

LEA EL MANUAL COMPLETO ANTES DE UTILIZAR ESTE •

PRODUCTO. CUALQUIER FALLA PODRÍA RESULTAR EN SERIAS

LESIONES O PODRÍA SER MORTAL.

LIRE ENTIÈREMENT LE GUIDE AVANTD’UTILISER CE PRODUIT. •

L’ÉCHEC DE FAIRE AINSI PEUT S’ENSUIVRE DANS LA BLESSURE

SÉRIEUSE OU LA MORT.

OWNER’S MANUAL•

MANUAL dEL USUARiO•

GUidE d’UTiLiSATiON•

Model / Modelo / Modèle: IP-1800I

Instant Power™

12V DC Power Source / Fuente de Poder para 12V DC /

Source d’Énergie de 12V CC

400 Watt Inverter / Inversor de Corriente de 400 Watt /

Onduleur de 400 Watts

Page is loading ...

TABLE OF CONTENTSTABLE OF CONTENTS

SECTION PAGE

IMPORTANT SAFETY INSTRUCTIONS 2

PERSONAL PRECAUTIONS 2

CONTROL PANEL 3

CHARGING THE INTERNAL BATTERY OF THE

INSTANT POWER™ 4

OPERATING INSTRUCTIONS 5

STORAGE 8

TROUBLESHOOTING 9

SPECIFICATIONS 9

ACCESSORIES 10

LIMITED WARRANTY 10

ÍNDICE

SECCIÓN PÀGINA

INSTRUCCIONES IMPORTANTES DE SEGURIDAD 13

PRECAUCIONES PERSONALES 13

TABLERO DE CONTROL 14

PARA CARGAR LA BATERIA INTERNA DE LA

INSTANT POWER™ 15

INSTRUCCIONES DE OPERACIÓN 16

ALMACENAJE 19

LOCALIZACIÓN Y SOLUCIÓN DE PROBLEMAS 20

ESPECIFICACIONES 21

ACCESORIOS 21

GARANTÍA LIMITADA 21

Page is loading ...

• 1 •

IMPORTANT: READ AND SAVE THIS SAFETY AND INSTRUCTION MANUAL.

SAVE THESE INSTRUCTIONS – Charge the Instant Power™ internal

battery immediately after purchase, after every use and every 30 days.

This manual will show you how to use your Instant Power™ safely and

effectively. Please read, understand and follow these instructions and pre-

cautions carefully, as this manual contains important safety and operating

instructions. The safety messages used throughout this manual contain a

signal word, a message and an icon.

The signal word indicates the level of the hazard in a situation.

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury to the operator or

bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury to the operator or

bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in moderate or minor injury to the operator or

bystanders.

Indicates a potentially hazardous situation which, if not avoided,

could result in damage to the equipment or vehicle or property

damage.

Safety messages in this manual contain two different type styles.

Unnumbered type states the hazard.•

Numbered type states how to avoid the hazard.•

The icon gives a graphical description of the potential hazard.

Pursuant to California Proposition 65, this product contains

chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

• 2 •

IMPORTANT SAFETY INSTRUCTIONS1.

Riskofelectricshockorre.

Use only recommended attachments. Use of an attachment not recom-1.1

mended or sold by Schumacher® Electric Corporation may result in a risk

ofre,electricshockorinjurytopersonsordamagetoproperty.

To reduce the risk of electric shock, unplug the 1.2 Instant Power™ from the

outlet before attempting any maintenance or cleaning. Simply turning off

the controls will not reduce this risk.

Remove personal metal items such as rings, bracelets, necklaces and 1.3

watches when working with a lead-acid battery. A lead-acid battery can

produce a short-circuit current high enough to weld a ring or the like to

metal, causing a severe burn.

Do not operate the 1.4 Instant Power™ with a damaged cables or clamps;

takeittoaqualiedserviceperson.(Callcustomerserviceat:1-800-621-

5485.)

Do not operate the 1.5 Instant Power™ if it has received a sharp blow, been

droppedorotherwisedamagedinanyway;takeittoaqualiedservice

person.(Callcustomerserviceat:1-800-621-5485.)

Do not disassemble the 1.6 Instant Power™;takeittoaqualiedserviceper-

son when service or repair is required. Incorrect reassembly may result in

ariskofreorelectricshock.(Callcustomerserviceat:1-800-621-5485.)

PERSONAL PRECAUTIONS2.

Risk of explosive gases. A spark

near the battery may cause a

battery explosion. To reduce the

risk of a spark near the battery:

Working in the vicinity of a lead-acid battery is dangerous. Batteries gener-2.1

ate explosive gases during normal battery operation. For this reason, it is

of utmost importance that you follow the instructions each time you use

the Instant Power™.

NEVERsmokeorallowasparkorameinthevicinityofabatteryor2.2

engine.

Do not permit the internal battery of the Instant Power™ to freeze. Never 2.3

charge a frozen battery.

To prevent sparking, NEVER allow clips to touch together or contact the 2.4

same piece of metal.

Be sure the area around the battery is well ventilated while the Instant 2.5

Power™ is being used.

• 3 •

Risk of contact with battery acid. Battery acid

is a highly corrosive sulfuric acid.

Consider having someone close enough by to come to your aid when you 2.6

work near a lead-acid battery.

Have plenty of fresh water and soap nearby in case battery acid contacts 2.7

your skin, clothing or eyes.

Wear complete eye and body protection, including safety goggles and pro-2.8

tective clothing. Avoid touching your eyes while working near the battery.

If battery acid contacts your skin or clothing, immediately wash the area 2.9

withsoapandwater.Ifacidentersyoureye,immediatelyoodtheeye

with cold running water for at least 10 minutes and get medical attention

right away.

Stay clear of fan blades, belts, pulleys and other parts that may cause 2.10

injury.

Clean the battery terminals before using the Instant Power™. During 2.11

cleaning, keep airborne corrosion from coming into contact with your eyes,

nose and mouth. Use baking soda and water to neutralize the battery acid

and help eliminate airborne corrosion. Do not touch your eyes, nose or

mouth.

Determine the voltage of the battery by referring to the vehicle owner’s 2.12

manual and make sure that the output voltage of the Instant Power™ is

correct.

Make sure that the Instant Power™ cable clips make tight connections.2.13

CONTROL PANEL3.

• 4 •

CHARGING THE INTERNAL BATTERY OF THE INSTANT POWER™4.

IMPORTANT: CHARGE IMMEDIATELY AFTER PURCHASE, AFTER

EACH USE AND EVERY 30 DAYS TO KEEP THE INSTANT POWER™

INTERNAL BATTERY FULLY CHARGED.

LED Indicators:4.1

TO CHECK THE INTERNAL BATTERY’S CHARGE STATUS, PRESS

THE BATTERY STATUS BUTTON ON THE FRONT OF THE INSTANT

POWER™.

The LEDlightswillindicatethechargelevelasfollows:

A red LED • indicates a 50% or less charge and you should immedi-

ately recharge the Instant Power™.

A yellow LED • indicates a 50 to 75% charge. The Instant Power™

may be used but should be recharged as soon as possible.

A green LED • indicates the internal battery is fully charged.

TheCHARGING(red)LED• indicates the Instant Power™ is charg-

ing(connectedtoanACpowersource.)Atfullcharge,theCHARGED

(green)LED will light.

Charging the Internal Battery using the Included Wall Charger.4.2

NOTE: The ON/OFF switch should be in the OFF position to recharge the

internal battery.

To charge, plug the included wall charger into the charger plug on the 1.

front of the Instant Power™.

Plug the wall charger into a 120V electrical wall outlet.2.

TheCHARGING(red)LED3. will light indicating charging.

TheCHARGED(green)LED4. will light when the battery has

reached full charge. This could take up to 72 hours due to the age and

condition of the battery. The charger will automatically go into maintain

mode and maintain the battery at full charge without damaging it.

Charge the Instant Power™ as soon as possible after use.5.

You may also charge the internal battery while driving, using the male-to-

malechargercable(p/n38-99-001564–notincluded).Insertoneendof

the accessory cable into the 12V DC power outlet and the other end into

thevehicle’saccessoryoutlet(lightersocket).Completelydisconnectthe

charger cable when the engine is not running.

TheCHARGING(red)LED and the CHARGED

(green)LED do not operate during this method of charging. Using

this method to charge the battery overrides the maintain mode and the

battery can be overcharged. Monitor the progress of the battery and when

itreachesafull(100%)charge,disconnectthecharger.Donotleavethe

battery unattended or it could explode causing property damage or

personal injury.

• 5 •

OPERATING INSTRUCTIONS5.

Jump Starting a Vehicle Engine5.1

Turn the vehicle’s ignition OFF before making the cable connections.1.

Foranegativegroundedsystem,clamptheredclip(+)tothepositive2.

terminal of the battery.

Clamptheblackclip(-)toanunpaintedandunmovingpartofthechas-3.

sis or engine block.

NOTE: In the rare case of jump starting a vehicle that has a positive-

groundedvehicleelectricalsystem,connecttheNEGATIVEblackclip(-)

tothenegativeterminal(-)ofthevehiclebattery.ThenconnectthePOSI-

TIVEredclip(+)toanunpaintedandunmovingpartofthevehiclechassis

or engine block. If you are unsure of the nature of the vehicle’s electrical

grounding system, check the owner’s manual of the vehicle. To disconnect

the clips, reverse the order.

Crank the engine. If the engine does not start within 5-8 seconds, 4.

stop cranking and wait at least 1 minute before attempting to start the

vehicleagain.(Thispermitsthebatterytocooldown.)

Aftertheenginestarts,disconnecttheblackclip(-)andthenthered5.

clip(+)inthatorder.

Recharge the Instant Power™ as soon as possible after use.6.

Risk of Explosion.

To prevent sparking, NEVER allow the clips to touch together or

to contact the same piece of metal. Never attempt to jump start a

frozen battery.

Before Using the Inverter5.2

Important Safety Instructions:

Keep the Instant Power™ well ventilated in order to properly disperse 1.

heat generated while it is in use. Make sure there are several inches of

clearance around the top and sides and do not block the vents on the

back of the Instant Power™.

Make sure the Instant Power™ is not close to any potential source of 2.

ammablefumes,gasesorclothing.

Keep the Instant Power™ dry.3.

DO NOT allow the Instant Power™ to come into contact with rain or 4.

moisture.

DO NOT operate the Instant Power™ if you, the Instant Power™, the 5.

device being operated or any other surfaces that may come in contact

with any power source are wet. Water and many other liquids can con-

duct electricity, which may lead to serious injury or death.

Do not place the Instant Power™ on or near heating vents, radiators or 6.

other sources of heat.

Do not place the Instant Power™ in direct sunlight. The ideal air tem-7.

perature for operation is between 50° and 80°F.

Do not use the inverter near an open engine compartment where 8.

fumes or gases may accumulate.

Do not modify the AC receptacles in any way.9.

• 6 •

Using the Inverter5.3

It is important to know the continuous wattage of the device you plan to

use with the inverter. The Instant Power™ must be used with devices

drawing 400 watts or less. If the wattage is not marked on the device, use

only devices that draw less than 4 Amps of AC current.

Devices like TVs, fans or electric motors require additional power to start

(commonlyknownasthe“startingorpeakpower”).TheInstantPower™

can supply a momentary surge in wattage; however even devices rated

less than the maximum 400 watts can exceed the inverters surge capabil-

ity and cause an automatic overload shutdown.

Do not use the inverter with a product that draws a higher wattage than

the inverter can provide, as this may cause damage to the inverter and the

product.

Makesurethedeviceyouareusingiscompatiblewithamodiedsine

wave inverter.

Always run a test to establish whether the inverter will

operate a particular piece of equipment or device.

NOTE: In the event of a power overload, the inverter is designed to auto-

matically shut down. This safety feature prevents damaging the inverter

while testing devices and equipment with the 400 watt range.

NOTE: If powering more than one device, start one device at a time to

avoid a power surge and/or inverter overload. The surge load of each

device should not exceed the inverter’s continuous operation wattage rate.

Powering a 120V AC Device5.4

Tooperatea120VACdevice:

Ensure the battery clips are securely clipped on the storage holders.1.

Plug the 120V AC device into the AC power outlet, and push the In-2.

verter Switch ON.

NOTE: the CHARGING LED also functions as the INVERTER ON LED

. When you push the inverter switch to the ON position, the LED will

light.

Ifthedevicedoesnotoperateproperlywhenrstconnectedtothe3.

inverter,pushtheinverterrockerswitchON(I),OFF(0),andON(I)

again in quick succession. If this procedure is not successful, it is likely

that the inverter does not have the required capacity to operate the

device intended.

Charge the Instant Power™ as soon as possible after each use.4.

Risk of electric shock.

Incorrect operation of your inverter may result in damage and

personal injury. The inverter output is 120V AC and can shock or

electrocute the same as any ordinary household AC wall outlet.

• 7 •

120V AC Electrical Device Example Run-Time Chart

Appliance Type Estimated

Power

Estimated

Time*

Spotlights, Sump Pumps,

DVD Players

100 Watts 1.3 Hours

Faxes, TVs, Small Power

Tools

150 Watts 50 Minutes

Computer Printer, Medium

Power Tools, Blenders

200 Watts 40 Minutes

NOTE: These are estimated run-times, actual time may vary. Times are

based on the internal battery being new, fully charged and operated at

room temperature

NOTE: The maximum continuous load is 400 watts. Do not use the

inverter with a product that draws more than 400 watts, as this may cause

damage to the inverter and the product.

Powering a 12V DC Device:5.5

The Instant Power™ is a power source for all 12V DC accessories that are

equippedwitha12Vaccessoryplug.Useitforpoweroutagesandshing

or camping trips. Estimated usage time is listed in the chart below.

Make sure the device to be powered is OFF before inserting the 12V DC

accessory plug into the 12V DC accessory outlet.

Open the protective cover of the DC power outlet on the side of the 1.

Instant Power™.

Plug the 12V DC device into the DC power outlet, and turn the 12V DC 2.

deviceon(ifrequired).

If the 12V DC device draws more than 15A or has a short circuit, the 3.

internal circuit breaker of the Instant Power™ will trip and disconnect

the power to the device. Disconnect the 12V DC device. The breaker

will automatically reset after an overload occurs.

The DC power outlet is wired directly to the internal battery. Extended

operation of a 12V DC device may result in excessive battery drain. Re-

charge immediately after unplugging the 12V DC device.

Appliance Type Estimated Wattage Estimated Usage Time

Cell Phone 4 watts 54 hours

Fluorescent Light 4 watts 54 hours

Radios, Fan 9 watts 24 hours

Depth Finder 9 watts 24 hours

Camcorder, VCR 15 watts 14.4 hours

Electrical Tool 24 watts 9 hours

Electrical Cooler 48 watts 4.5 hours

Car Vacuum, Air

Compressor

80 watts 2.7 hours

• 8 •

NOTE: Estimated run-times. Actual time may vary. Times are based on

the internal battery being fully charged

Flex-Light 5.6

Tousetheex-light,insertthelight’splugintothe12Vaccessoryoutlet.

The ON/OFF control is on the back of the light.

Light Replacement

The bulb used in the Instant Power™ light is a 12 volt, 5 watt halogen bayo-

net type. Since the bulb needing replacement is not working and the switch

maybeintheONposition,thelampcircuitcouldbe“live”.Use caution

while changing the bulb.

Disconnect the light from the 12V accessory outlet.1.

To replace the bulb, unscrew the cover on the lamp back, remove the 2.

old bulb, then replace with a new 12 volt, 5 watt halogen bulb.

Finally, screw the cover onto the lamp housing.3.

STORAGE6.

IMPORTANT:

CHARGE IMMEDIATELY AFTER PURCHASE•

KEEP FULLY CHARGED•

ChargetheInstantPower™internalbatterybeforerstuseandafter

every use thereafter.

All batteries are affected by temperature. The ideal storage temperature is

at 70 degrees Fahrenheit. The internal battery will gradually self-discharge

(losepower)overtime,especiallyinwarmenvironments.Leavingthe

battery in a discharged state may result in permanent battery damage. To

ensure satisfactory performance and avoid permanent damage, charge

the internal battery every month.

The clips on the Instant Power™ are live and will produce arcing or spark-

ing if they come in contact with each other. To prevent accidental arcing,

always keep the clips on the storage holders when not using it to jump

start a vehicle.

• 9 •

TROUBLESHOOTING7.

PROBLEM POSSIBLE CAUSE REASON/SOLUTION

The Instant Power™ won’t

jump start my car.

Clips are not making a

good connection to the

battery.

Connections are reversed.

The Instant Power™ bat-

tery is not charged.

The vehicle’s battery is

defective.

Check for poor connection

to battery and frame. Make

sure connection points are

clean. Rock clips back and

forth for a better connection.

Disconnect the Instant

Power™ and reverse the

clips.

Check the battery charge

status by pressing the

button on the front of the

Instant Power™. See LED

Indicators section of this

manual.

Have the battery checked.

The Instant Power™ won’t

power my 12V device.

The 12V device is not

turned on.

The Instant Power™ bat-

tery is not charged.

The 12V device draws

more than 15A or has a

short circuit

Turn on the 12V device.

Check the battery charge

status by pressing the

button on the front of the

Instant Power™. See LED

Indicators section of this

manual.

Disconnect the 12V device.

The internal breaker will

automatically reset after a

minute or two. Try the 12V

device again. If it happens

again, replace the 12V

device.

The battery in the Instant

Power™ won’t hold a

charge.

Thebatteryisbad(willnot

accept a charge).

Have the battery checked.

SPECIFICATIONS8.

Internal Battery Type Maintenance-free AGM Lead-Acid

Nominal Voltage 12V DC

Capacity 18 Ah

DCPowerOutlet(Max.ContinuousLoad) 15A

Dimensions(HxWxD) 29.21 x 24.13 x 19,66 cm

Weight 8.5 kg.

• 10 •

InverterSpecications

Maximum Continuous Power 400 Watts

SurgeCapacity(OutputWattage) 800 Watts

No Load Current Draw <0.4 Amps

Wave Form ModiedSineWave

AC Outlets Two, 120V AC 3-Prong grounded

ACCESSORIES9.

Male-To-Male Accessory Cable-------------------------------------38-99-001564

LIMITED WARRANTY10.

SCHUMACHER ELECTRIC CORPORATION, 801 BUSINESS CENTER

DRIVE, MOUNT PROSPECT, IL 60056-2179, MAKES THIS LIMITED

WARRANTY TO THE ORIGINAL RETAIL PURCHASER OF THIS PROD-

UCT. THIS LIMITED WARRANTY IS NOT TRANSFERABLE OR AS-

SIGNABLE.

SchumacherElectricCorporation(the“Manufacturer”)warrantsthis

Instant Power™ for one year and the internal battery for ninety days from

the date of purchase at retail against defective material or workmanship

that may occur under normal use and care. If your unit is not free from

defective material or workmanship, Manufacturers obligation under this

warranty is solely to repair or replace your product, with a new or re-

conditioned unit, at the option of the Manufacturer. It is the obligation of

the purchaser to forward the unit, along with mailing charges prepaid to

the Manufacturer or its authorized representatives in order for repair or

replacement to occur.

Manufacturer does not provide any warranty for any accessories used with

this product that are not manufactured by Schumacher Electric Corpora-

tion and approved for use with this product. This Limited Warranty is void

if the product is misused, subjected to careless handling, repaired, or

modiedbyanyoneotherthanManufacturerorifthisunitisresoldthrough

an unauthorized retailer.

Manufacturer makes no other warranties, including, but not limited to,

express, implied or statutory warranties, including without limitation, any

impliedwarrantyofmerchantabilityorimpliedwarrantyoftnessforapar-

ticular purpose. Further, Manufacturer shall not be liable for any incidental,

special or consequential damage claims incurred by purchasers, users or

others associated with this product, including, but not limited to, lost prof-

its, revenues, anticipated sales, business opportunities, goodwill, business

interruption and any other injury or damage. Any and all such warranties,

other than the limited warranty included herein, are hereby expressly

disclaimed and excluded. Some states do not allow the exclusion or limita-

tion of incidental or consequential damages or length of implied warranty,

so the above limitations or exclusions may not apply to you. This warranty

givesyouspeciclegalrightsanditispossibleyoumayhaveotherrights

which vary from this warranty.

• 11 •

THIS LIMITED WARRANTY IS THE ONLY EXPRESS LIMITED WAR-

RANTY AND THE MANUFACTURER NEITHER ASSUMES OR AUTHO-

RIZES ANYONE TO ASSUME OR MAKE ANY OTHER OBLIGATION

TOWARDS THE PRODUCT OTHER THAN THIS WARRANTY.

Schumacher Electric Corporation Customer Service

1-800-621-5485

Monday – Friday 7:00 a.m. to 5:00 p.m. CST

Schumacher and the Schumacher Logo are registered trademarks of

Schumacher Electric Corporation

Page is loading ...

Schumacher 00-99-000990-0809 User manual

This manual is also suitable for

Schumacher 00-99-000990-0809 User manual

in other languages

Related papers

Other documents