Hampton Bay EC8070NM User guide

Brand: Hampton Bay

Model: EC8070NM

Category: Work lights

Type: User guide

INSTRUCTION MANUAL

Faux Alabaster Glass Semi-Flush

Nut Meg Finish

Home Depot SKU 555-004 (UPC008938280730)

Thank you for purchasing this Hampton Bay Semi-Flush. This product has been manufactured with the highest

standards of safety and quality.

FEATURES:

1. The Faux Alabaster Glass Semi-Flush in NM finish. This Semi-Flush is available online at

www.homedepot.com or through special order at your local Home Depot store.

2. This fixture has been engineered to safely use up to Two 100 watt MAX, incandescent light bulbs.

3. Can be used with any standard 120 volt incandescent style dimmer switch (not included).

QUESTIONS, PROBLEMS, MISSING PARTS:

Before returning to your local Home Depot, please call our Customer Service Team at 1-877-527-0313 or visit

www.homedepot.com. Please reference your SKU 555-004 or UPC008938280730.

CAUTION:

1. Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off

the circuit breaker or by removing the fuse at the fuse box.

2. Refer to the re-lamping label near the lamp holder for recommended wattage.

3. Release the glass gently after tightening the wires with the decorative screw nuts to avoid breakage.

4. CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.

5. If you have any non-electrical questions about this fixture, please contact our Customer Service team at 1-877-

527-0313 or visit www.homedepot.com. Please reference your SKU 555-004 or UPC008938280730.

6. Keep your receipt as proof of purchase.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

TOOLS REQUIRED FOR ASSEMBLY & INSTALLATION (not included):

Bulbs Safety Goggles Ladder Pliers Wire Strippers Flathead Phillips Electrical tape

Cutters Screwdriver Screwdriver

PARTS INCLUDED FOR ASSEMBLY (parts are not to scale):

Glass shade (# 5) Fixture Body (# 1) Ball Nut (# 4) Support Stem (# 2)

ASSEMBLY INSTRUCTIONS:

1. Carefully unpack the fixture.

2. Lay out all parts on a clean surface.

3. Put the threaded end of hanging tube (#2), through the fixture (#1) and then through the glass shade

(#5).Use the spherical nut (#4) to lock them in place.

4. Install two 100 watt light bulbs (#3) into the lamp sockets.

ASSEMBLY:

# Part Description

1 Fixture Body

2 Support Stem

3 Bulb

4 Round Nut

5 Glass Shade

PARTS INCLUDED FOR INSTALLATION (parts are not to scale):

x1 Ground x2 Round x3 Wire Outlet Box Long mounting Hex Nut (#14) Mounting

Screw (#9) Nut (# 12) connectors (#7) Screw (#11) Screw (#13) Strap (#10)

INSTALLATION INSTRUCTIONS:

1. Turn off the power by either turning off the breaker at the electrical panel or by removing the fuse from the

fuse box.

2. If you are replacing an existing fixture, disconnect and remove the old fixture. Expose the supply wiring

from the outlet box.

3. Install long mounting screws (#13) into the mounting strap (#10) and lock in place and with the hex nut

(#14)

4. Attach the mounting strap (#10) to the outlet box (#6) using the outlet box screws (#11)

5. Wrap the ground wire from the fixture around the Ground Screw (#9) on the Mounting Strap (#10), and

then connect the ground wire from the fixture to the ground wire from the Outlet Box (#6).

6. Connect the black wire from the fixture (#1) to the black wire from the supply circuit in the outlet box (#6)

and secure with a wire connector #7).

7. Connect the white wire from the fixture (#1) to the white wire from the supply circuit in the outlet box (#6)

and secure with a wire connector #7).

8. Install the fixture body (#1) over the 2 long mounting screws (#13) and secure in place with the round nuts

(#12). Adjust the hex nuts (#14) at this time to ensure a tight fit to the ceiling.

9. Installation is now complete. Turn on the power at the circuit breaker or fuse box. Turn the light switch on

to activate the fixture.

INSTALLATION:

# Part Description

6 Outlet Box

7 Wire Connector

8 Ground Wire

9 Ground Screw

10 Mounting Strap

11 Outlet Box Screw

1 Fixture Body

12 Round Nut

13 Long Mounting Screw

14 Hex Nut

TROUBLESHOOTING:

PRODUCT MAINTENANCE:

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth to wipe the shade and surface

of the fixture.

2. To clean the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker or

by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth to wipe the inside

glass and interior surface of the fixture.

3. Allow the fixture to dry thoroughly before turning the power back on.

CAUTION: Do not use any cleaners with chemicals, solvents or harsh abrasives as damage to components or

finish may occur.

LIMITED WARRANTY

The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period

of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to

products used in normal use and service. If this product is found to be defective, the manufacturer’s only

obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion,

provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations,

neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly

installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This

warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration,

or faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not

apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal

wear and tear. The manufacturer does not warrant and specially disclaims any warranty, whether express or

implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically

disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not

limited to any labor / expense costs involved in the replacement or repair of said product.

Problem Possible Cause Corrective Action

1. Light bulb is burned out. 1. Replace light bulb.

2. Power is off. 2. Make sure power supply is on.

3. Faulty wire connection. 3. Check wiring.

Light Bulb will not illuminate.

4. Faulty switch. 4. Test or replace switch.

Fuse blows or circuit breaker

trips when light bulb is

illuminated.

Crossed wires or power wire is

grounding out.

Check wire connections.

Page is loading ...

Hampton Bay EC8070NM User guide

Brand: Hampton Bay

Model: EC8070NM

Category: Work lights

Type: User guide

Download PDF

report

in other languages

français: Hampton Bay EC8070NM Mode d'emploi
español: Hampton Bay EC8070NM Guía del usuario

Hampton Bay EC8070NM User guide

Hampton Bay EC8070NM User guide

in other languages

Related papers

Other documents