GE AE0CD14DM0V1 Owner's manual

0

|

0_

0 91wwlmlm

Safety Instructions ............ 2

Operating Instructions

Batteries ............................ 3

Careand Cleaning ............... 6, 7

RemoteControlFeatures ........ 4, 5

Installation Instructions

AirPurgingand LeakageTest..... 15

BeforeYouBegin ................... 8

ConnectionTubing ............... 11

Dimensions ........................ 9

Drainage Hose ................... 11

ElectricalRequirements............. 8

ElectricalWiring .............. 12-14

Indoor Unit .................... 12,1:3

Location .......................... 10

Outdoor Unit .................. 14,15

Tubing Hole....................... 11

PowerLine........................ 14

Mounting Plate ................... 11

TestOperation .................... 16

Wiring Indoor Unit ................ 12

Wiring Outdoor Unit .............. 14

Troubleshooting Tips ........ 17

Normal Operating Sounds........ 17

Consumer Support

ConsumerSupport ...... BackCover

Warrantg ......................... 18

Cool Only Models

AE1CDIOAM / AEOCDIOAM

AE1CD14DM / AEOCD14DM

AE1CD2ODM / AEOCD2ODM

Heat/Cool Models

AE1 RD10AM / AEORD10AM

AE1 RD14DM / AEORD14DM

AE1 RD2ODM / AEORD2ODM

Climatiseurs

inibloc

La section franqaise commence a la page 19

Acondicionadordeaire

desistemaminisplit

La secci6n en espahol empieza en la pdgina 37

Write the model und seriul numbers here

for the indoor und outdoor units:

Indoor Model #

Indoor Seriul #

Outdoor Model #

Outdoor Seriul #

Find these numbers on a label on the side of

eachunit.

49-7600 05-09JR

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

tl WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric

shock or personal injury.

SAFETY PRECAUTIONS

Use this equipment onlg for its intended

purpose as described in this Owner's

Manual.

This sgstem must be properlg installed

in accordance with the Installation

Instructions before it is used.

@All wiring should be rated appropriate for

the current value listed on the rating plate.

Use onlg copper wiring.

,tl, WARNING!Riskofelectric

shock. Can cause injurg or death: Earth

connection is essential before connecting

the power supplg.

,_ WAR N ! N G_ Riskof electric

shock. Can cause injurg or death: Disconnect

all remote electric power supplies before

servicing.

WARN!NG!Riskof electric

shock. Can cause injurg or death: Repair or

replace immediatelg all electrical wiring

that has become fraged or otherwise

damaged. Do not use wiring that shows

cracks or abrasion damage along its

length or at either end.

iiiiiiiiiiii_iiii_

All electrical work must be completed bg a

qualified electrician and completed to local

and national building codes and regulations.

Any servicing must be performed by a

qualified individual.

WARNING!Riskof fire. Can

cause injurg or death: Do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinitg

of this or ang other appliance.

For any service which requires entry

into the refrigerant sealed system,

Federal regulations require the work

be performed by a technician having

a Class II or Universal certification.

iiiiiiiiiiii_iiii_

All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If gou are getting

rid of an old product with refrigerants, check

with the compang handling disposal.

R/410Aair conditioning sgstems require

contractors and technicians to use tools,

equipment and safetg standards approved

for use with this refrigerant. DO NOT use

equipment certified for R22 refrigerant onlg.

READAND FOLLOW THISSAFETY INFORMATION

CAREFULLY.

SAVE THESE INSTRUCTIONS

Operating the air conditioner. GEAppliances.com

General Procedure

NOTE:Forbest results,point the remote control

at the indoor unit.

r-_ Hake surepower isconnected and pressthe

ON/OFFpad to start the sgstem.

F2-] Pressthe NODE pad to selectthe desired

operation mode.

r-_ Pressthe SWINGpad for automatic rotation of

the louvers.Pressagain to stop the rotation.

[_] Pressthe FAN pad to setthe desiredfan speed

(AUTO/Low/Medium/High).

[_ Pressthe TENP+/- pads to set the desired

temperature.

NOTE:Fordetailed remote control instructions, see

About the remote control section.

How to Insert Batteries

Theremote control usestwo AM batteries.

r-_ Removethe cover from the back of the remote

control and insert two new batteries (pag

attention to the polaritg).

F2-] Reattach the cover.

NOTES:

m Do not mix new and usedbatteries or different

tgpes of batteries.

[] Removebatterieswhen the remote control isnot

in usefor an extended time.

[] The remote control signal can onlg be received

within a range of 20ft.

[] The remote control should be placed about

] feet or more awag from TVsetsor ang other

electrical appliances.

Batterytype:AAA

-- Batterycover

]

About the remote control.

Theremotecontrol transmitsthesignalsto thesystem.

Featuresand appearancemay vary.

AUTO--In this mode, the unit automatica%

controls the room temperature within the

range of 77°F and 68°F.The fan will run

continuously while the unit is in AUTOmode.

When the room temperature exceeds 77°F,the

unit will go into COOLMode. When the room

temperature drops to 73°F,the fan will

continue to run but COOLMode will turn off.

When the temperature drops below 68°F,the

unit will go into HEATMode. When the

temperature reaches 73°F,the fan will

continue to run but HEATMode turns off.

NOTE:This temperature range setting cannot

be adjusted and will not be displaged.

¢_ COOL--Use to cool the room to the desired

temperature set between 61°F and 86°F.

NOTE:The unit will not provide optimum

cooling if the outside temperature is below

60°F. Under certain conditions, the unit mag

activate the antifreeze protection cgcle for

approximatelg 5 minutes to remove ice from

the indoor coil.

666DRY--Use to dehumidifg the room. The fan will

run at a fixed low speed to provide maximum

dehumidification. The temperature can be set

between 61°F and 86°F.

_€ FAN--Use to turn ON and OFFthe fan-onlg

operation. COOL,HEATor DRYmode will not

be provided.

_X HEAT (on models so equipped)--Use to warm

the room to the desired temperature set

between 61°F and 86°F.

NOTE:The unit will not provide optimum

heating if the outside temperature is below

14°F.Under certain conditions, the unit mag

activate the antifreeze protection cgcle for

approximatelg 8 minutes to remove ice from

the outdoor coil. During this cgcle, it is normal

to hear operating sounds such as refrigerant

flowing inside the sgstem.

e

o

______@

@

-- Operation

-- Sleep on

gon

-- Clock andtimer

About the remote control. contJ

The remote control transmits the signals to the system.

GEAppliances.com

Features of the Remote Control

O isplag 0

Displagsall set contents when turned on.

Displagsonlg the set temperature and time

when turned off.

O

0

ON/OFF Pad

Pressto turn the sgstem on and off.

MODE Pad

Pressto change the operation mode to

AUTO,_ (COOL),666(DRY),dSf_(FANONLY)

or _:_(HEAT).

TEMP Pads

Press+to increasethe set temperature in

!°F increments. Press- to decrease the set

temperature in !°F increments.Inthe COOL

and HEATmodes,the settemperature can

be selected from 6!°F to 86°RTheset

temperature will not be displaged in the

AUTOmode.

FAN Pad

Pressto change the fan speedto AUTO

FAN,-,,(LowFan),..,J (Medium Fan)or

_-,IJ (HighFan).

SWING Pad

Pressfor automatic rotation of the louvers.

Pressagain to stop them from rotating.

SLEEPPad

Pressto turn the sleepmode on and off.

When in the cooling mode and the sleep

timer isset,the set temperature will

automaticallg increase 2°Fafter the first

hour and 2°Fafter the second hour.SLEEP

Mode iscompatible with COOL,HEATand

DRY.

CLOCK Pad

Pressto set the time of dag. PressTIME-or

TIME+padsto set the time in 1-minute

increments.Pressand hold the TIME-or

TIME+padsto set the time in !0-minute

increments.

O

0

T-ON (Timer © ON) Pad

When the air conditioner is off,pressT-ON

(timer on)to set it to turn on automaticallg

(usingits previoussettings)at the time gou

set.

PressTIME- or TIME+pads to set the start

time in 1-minute increments.

Pressand hold the TIME-or TIME+ padsto

set the start time in !0-minute increments.

TocancelQ ON (T-ON),pressthe CANCEL

pad.

T-OFF (Timer © OFF)Pad

When the air conditioner ison,pressT-OFF

(timer off)to set itto automatically turn off

at the time you set.

PressTIME- or TIME+pads to set the turn-

off time in 1-minute increments.

Pressand hold the TIME-or TIME+ padsto

set the turn-off time in !0-minute

increments.

Tocancel © OFF(T-OFF),pressthe

CANCELpad.

TIME Pads

Usewhen setting the CLOCKand timers

(T-ONand T-OFF).Pressto set in 1-minute

increments. Pressand hold to set in

!0-minute increments.

CANCEL Pad

Pressto cancel the timer(s).

Careand cleaning of the air conditioner.

Indoor Unit

Grille, Case and Remote Control

Turn the sgstem off beforecleaning. Toclean,

wipe with a soft, drg cloth. Donot usebleach

or abrasives.

Air intakevent

Airoutletvent

Air Filters

Thetwo air filters behind the front grilleshould be

checked and cleaned at least everg 30 dags or

more often, ifnecessarg.

r_ open the front access panel.

F2-] Pullthe filter tab slightlg forward to remove the

filter.Cleanthe filter with a vacuum or warm,

soapgwater. Rinseand allow the filter to drg

before replacing it.

r_ Reinsertthe filters and closethe front access

panel.

NOTE:DONOToperate the sgstem without a filter

becausedirt and lint will clog it and reduce

performance.

Outdoor Unit

The heat exchanger coils and panel vents of

the outdoor unit should be checked regularlg.

If clogged with dirt or debris, the heat exchanger

and panel vents should be professionallg

cleaned.

NOTES:

mPower supplgmust be disconnectedbefore

cleaningthe outdoor unit.

mOirt_lor cloggedcoils wi!!reducethe operating

e_ciency ofthe sgstem and cause higher

operating costs.

Airintake

vents

Airoutlet

vent

GEAppliances.com

If you're closing up for the season...

IT] Operate the sgstem in the fan mode for 2

hours. This will drg out the sgstem.

[_ Remove the batteries from the remote control.

[_ Cover the outdoor unit with a protective cover.

NOTE: Next season make sure to remove the

protective cover from the outdoor unit before

restarting the sgstem.

I

stall tio

structio

Mi

Air

i Split-Sg

Co diti

te

e

BEFORE YOU BEGIN

Readthese instructions completely and

carefuIIg.

• IMPORTANT - savethese instructions for local

inspector's use.

• IMPORTANT - Observeallgoverningcodes

and ordinances.

• Note to Installer - Besure to leave these instructions

with the Consumer.

• Note to Consumer - Keep these instructions for future

reference.

• Skill level - A licensed, certified (to handle refrigerant-

R410A,recovery, etc.)technician and a qualified

electrician ore required for installation of this split

air conditioning system.

• Completion time - Approximately 2V2hours

• Two people are required to install this unit due to

the weight of the product.

• Proper installation isthe responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• For personal safety, this system must be properly

grounded.

• Protective devices (fuses or circuit breakers)

acceptable for installation ore specified on the

nameplate of each unit.

• Servicing and installation of the refrigerant system

must be performed only by a licensed, HVAC-certified

technician.

• Make sure to avoid wiring or plumbing inside the wall

when installing.

• Forany service which requires entry into the refrigerant

sealed system, Federal regulations require the work be

performed by o technician having o Class IIor Universal

certification.

ELECTRICAL REQUIREMENTS

• Becertain all wiring complieswith local building codes and

NECand that the supply voltage for this system iscorrect.

Thesystem supply voltage isconnected to the outdoor

unit only.

• Checkthe rating nameplate on the sidepanel of outdoor

unit for requiredcircuit protection rating and required supply

voltage.

UseUL-opprovedelectrical branch circuit disconnect

for providing supply voltage to split system indoor and

outdoor units.Locate disconnect within sight and readily

accessibleper NECand localcodes.

Allwiring shouldbe rated appropriate for the current value

listed on the rating plate.

• Becertain there isan uninterrupted, unbroken electrical

ground connection.

• Wiring should be encased in liquid-tight tubing with

connections sealedwith liquid-tight connectors.

-&CAUTION:

• Do not use on extension cord with this system.

• Aluminum building wiring mag present special

problems-consult a qualified electrician.

• When the unit is in the STOPposition, there is still

voltage to the electrical controls.

• Disconnect the power to the system before

servicing bg removing the branch circuit fuses

or turning the circuit breakers off at the panel.

• DO NOT use equipment certified for R22refrigerant

only.

Installation Instructions

PARTS INCLUDED

• Mounting plate

• Sealer

• Screws(5for 10,000and

la,000 BTUmodels/10 for

20,000 BTUmodels)

• Remotecontrol

• BatteriesAAA(2)

• Drainagehose

• Insulationhose

• Two (2)filters

SUPPLIED BY INSTALLER

Adapter: 1/4" male flare with Schrader

valve x 5/16" female (1/2"-20UN)

OPTIONAL ACCESSORY KITS

To aid installation, the following tubing kits may be

ordered:

GE Kit TUE1650 TUE3250

Foruseon models AE1CD!0AM

AEOCD!0AM

AE1RD10AM

AEORD10AM

AE1CD!4DM

AEOCD14DM

AEIRD14DM

AEORD14DM

1/2" x 16 ft.

1/4" x 16 ft.

16 ft.

included

Suction line dia. and length 1/2" x 32 ft.

Liquid line dia. and length 1/4" x 32 ft.

Tube insulation length 32 ft.

Wall hole sleeves (2) included

PVCwrapping tape included

GE Kit

For use on models

TUE1662 TUE3262

AE1CD20DM

AEOCD20DM

AEIRD20DM

AEORD20DM

Suction line dia. and length 5/8" x 16ft. 5/8" x 32 ft.

Liquid line dia. and length 3/8" x 16ft. 3/8" x 32 ft.

Tube insulation length 16 ft. 32 ft.

Wall hole sleeves (2) included included

PVCwrapping tape included included

INSTALLATION DIMENSIONS

_6" ormorespace

6" or more _ tothe ceiling 6" or more

spaceto f'//' ......................_................... spaceto

thewall f/ " ' "_ tf?e_all

,

118"ormore_ 79"ormore_ // VVrappiFg

airoutletside, hspacetothe --I- TublnoTuhin_holehnb,tapep

T_oor T sleeve

:"20"ormorespace

Ltothecover

12"ormore

spacetothe

wall

79"or moreair

outlet side

21¼"-10Kand14KBTUmodels

22_?'-20KBTUmodels

11¼"-10Kand14KBTUmodels

11_"-20KBTUmodels

IMPORTANT NOTES:

,,The installation must be done bg a trained

and qualified electrician and technician with

Class II or Universal certification.

,,When picking up and moving the units,

you must be guided bg trained and qualified

personnel.

Installation Instructions

Read these instructions completely and carefully; then follow step by step.

SELECT THE BEST LOCATION

r_ INDOOR UNIT

• Do not allow ang heat or steam near the unit.

• Select a location where there are no obstacles

in front of the unit.

• Make sure that condensate drainage can be

convenientlg routed awag.

• Do not install near a doorwag.

• Ensure that the space around the left and right

of the unit is more than 6". The unit should be

installed as high on the wall as possible, allowing

a minimum of 6" from ceiling.

• Use a stud finder to locate studs for mounting and

to prevent unnecessarg damage to the wall.

• Install on studs and in a location from which

the condensation water can be drained out

convenientlg and that permits easg connection

with the outdoor unit.

• Do not cover the inlet and outlet so that the

outflow air can reach all parts of the room.

• Install in a location that is strong enough to

withstand the full weight and vibration of the unit.

• Be sure that the installation conforms to the

installation dimension diagram.

• Leave enough space to allow access for routine

maintenance. The height of the installed location

should be 79" or more awag from the floor.

• Install in a location that is 3 ft. or more awag from

other electrical appliances, such as televisions and

audio devices.

• Select a location that gives gou easg access to

remove and clean the filter.

Morethan6"

More f, _ , , .... More

Morethan79"

[]OUTDOOR UNIT

• If an awning is built over the unit to prevent direct

sunlight or rain exposure, make sure that heat

radiation from the condenser is not restricted.

• Ensure that the space around the back and sides

is more than 12". The front of the unit should have

more than 79" of space.

H

Morethan12"

Theplatformmust

supporta minimumof

Morethan79" 200Ibs.SeeInstallation

Dimensionsformounting

holespacing.

• Install in a location that is strong enough to permit

safe installation and to withstand the full weight

and vibration of the unit.

• Construct and anchor o strong and level mounting

base or pod for the outdoor unit.

• Anchor the outdoor unit through its four mounts,

using bolts.

• Select o location from which noise and outflow

air emitted bg the unit will not inconvenience

neighbors.

• In humid locations, the unit mog sweat and

condensation (water) mag drip from it. Take this

into consideration when choosing the location.

• Select a location that has sufficient ventilation.

• Do not cover the inlet and outlet.

• Install unit owog from flammable gas or corrosive

gas leaks.

• Be sure the installation conforms to the installation

dimension diagram.

• Rooftop Installations:

If the outdoor unit is installed on a roof structure,

be sure to level the unit. Ensure the roof structure

and anchoring method are adequate for the unit

location. Consult local codes regarding rooftop

mounting.

10

Installation Instructions

INSTALLATION

[] INSTALL THE MOUNTING PLATE

• Always mount the mounting plate horizontally.

• Attach the mounting plate at the selected location

with screws supplied with the unit.

• Be sure that the mounting plate has been

attached firmly enough to withstand the weight

of on adult of 130 Ibs. Also, the weight should be

evenly shored by each screw.

171INSTALL THE TUBING HOLE

• Make the tubing hole in the wall at o slight

downward slant to the outdoor side.

3"fromright

edgetocenterof

righttubinghole

f

\

Holeis2"diameterfor1OKand14KBTU l_A''frombottom

modelsand2_''diameterfor edgetocenterof

20KBTUmodels, righttubinghole

• To let water drain and prevent damage to wiring

and tubing, insert o 2V/' plastic pipe, cut to o

length equal to the wall depth. Insert the tubing

and wiring through the pipe.

• Copper tubing should be copped until ready to

install flare fitting, to prevent contamination.

[_] INSTALL THE DRAINAGE HOSE

• For good drainage, the drain hose should be

placed at o downward slant.

• Do not wrench or bend the drain hose or allow

it to contact standing water.

• The extended drainage tube in the room should

be wrapped with the insulating materials.

\

X X Flooded

I_ INSTALL THE CONNECTION TUBING

• Connect the copper tubing with the relevant union

tubes of the indoor unit and tighten the flare nut

of the connection tubes.

NOTE: Be careful when bending the connection

tubes to ovoid damaging them.

1. Align the center of the tube flere with the relevant

velve.

2. Screw in the flare nut by hand end then tighten

the nut with spanner and torque wrench. See the

table below for the correct torque.

3. Connecting tube specifications ere shown below:

10,000/14,00020,000

Specifications BTU Units BTU Units

DesignLength 20 ft. 26.2ft.

Extra RefrigerantCharge 0.16oz./ft. 0.54oz./ft.

PerFt.AboveDesignLength

Outer Diameter Liquid Pipe 1/4" 3/8"

Outer Diameter GasPipe 1/2" 5/8"

Max.Distance Height 33 ft. 33ft.

Max.Distance Length 68 ft. 98 ft.

NOTE: Exceeding tightening torque will damage

the copper tubing.

Tightening torque table

Tubing OD

1/4"

3/8"

1/2"

5/8"

Tightening torque(in./Ib.)

140-170

270-310

440-480

530-570

Flarenut

Joint

Spanner

uewrench

11

Installation Instructions

INSTALLATION (cont.}

[_] CONNECT ELECTRICAL WIRING

BETWEEN INDOOR AND OUTDOOR

UNITS

• All wiring should be rated appropriately for the

current value listed on the rating plate.

• The power supply should accommodate the rated

voltage.

• Wiring must be done by a qualified electrician

according to local codes, regulations and this

manual.

• All wiring connections should be tightened securely.

[61WIRE THE INDOOR UNIT

NOTE: Use UL-approved electrical branch circuit

disconnect for providing supply voltage to split system

indoor and outdoor units. Locate disconnect within sight

ond readilg occessible per NECand local codes.

1. Open the front access panel.

2. Remove the cover plate of the electrical box.

\

:::::::':_ Accesspanel

i -- Coverplate

J o

3. On the back of the indoor unit, remove the

conduit connecting cover. Using the fixing nut,

connect the conduit to the connecting cover.

Route the wire leads through the unit to the

electrical box area. Reinstall the connecting cover.

Backof unit IIII

Fixingnut /1/

Connecting cover

Conduit

12

F6]WIRE THE INDOOR UNIT {cont.}

NOTE: Wiring must be done by a qualified electrician

according to the local codes and regulations and

this manual. The connecting wire should be correctly

connected to the circuit interface.

Electricalwiresmustbesecured

with attachedstrainreliefs.

_w -way

terminal

board

er

j onnection

cord

115VModels Outdoorunit Indoorunit

Tobranch

circuit

Powersupply _

:tI:i!

roun

3.

o

_3J

B_

%1will beusedfor neutral

in 115Vmodels.

230/208V Models

Outdoorunit

Tobranch

circuit

Powersupply _1

Indoorunit

NOTES:

• Wiring should be consistent with the wiring

diagrams above.

• Tighten the nut of the terminal board to keep

the board secured.

• After tightening, the wire cannot be removed

if pulled.

• Incorrect wiring will cause the air conditioner

to work abnormally.

• Incorrect grounding will cause a short circuit.

4. Replace the cover plate over the electrical box

and lower the access panel into position.

Installation Instructions

INSTALLATION (cont.}

[71INSTALL THE INDOOR UNIT

• Route the tubes and wiring from the right side of

the indoor unit. Cut off the railings from the

chassis as necessary.

1. Cut off tailings 1 when routing the wiring only.

2. Cut off railings 1 and 2 (or railings 1, 2 and 3)

when routing both the wiring and tubing. (_ and

(_ below are the recommended tubing.

C) Right

tube

jTailings 3

I Jl jTailings 2

I_[_ i-- Tailings1

[2] INSTALL THE INDOOR UNIT (cont.}

• Wrap the tubes and wiring and pull them through

the cut-off-tailings hole.

Wrappingtape

Connectiontubes

Power Controlcord(for

connectioncord cooling/heating

typeonly)

Drainagehose

• Hang the mounting slots of the indoor unit on

the upper tabs of the mounting plate and make

sure it is firm enough.

• The height of the installed location should be

79" or more from the floor.

13

Installation Instructions

INSTALLATION (cont.}

[_]WIRE THE OUTDOOR UNIT

1. Open the cover of the outdoor unit.

2. The connecting wire lead from the terminal board

of the indoor unit must be connected correctly.

3. The connecting wire should be a little longer so

that it can be maintained easily.

6-wayterminalboard

\

,x

\\

O

©

Wrapelectricalcordswith attached

metaltietoprovidestrainrelief.

10,000and14,000BTUModels

115VModels Outdoorunit Indoorunit

Tobranch

circuit

Powersupply _]

roun

%1will beusedfor neutral

in 115Vmodels.

230/208VModels Outdoorunit

Powersupply _

T° r nchl

circuit

Ground_ I

Indoorunit

FsqWIRE THE OUTDOOR UNIT (cont.}

NOTES:

• Wiring should be consistent with the above wiring

diagrams.

• Wiring must be correct.

• Tighten the nut of the terminal board to keep the

board secured.

• After tightening, the wire cannot be removed if

pulled.

• Incorrect wiring will cause the air conditioner to

work abnormally.

• Incorrect grounding will cause a short circuit.

• Electrical connections must be made by a qualified

electrician.

• All electrical work must be completed according to

local codes and regulations.

[] INSTALL THE POWER LINE

1. Open the wiring cover and remove the knockouts.

2. The connector should be secured by the nut, and

the wiring cover should be replaced and secured

with the included screw.

3. All wiring should be protected by liquid-tight

tubing, and connections to the wiring cover

should be with liquid-tight connectors.

14

Electricalbox

assembly

Wiringcover

Connector

NOTES:

• The connecting wire and connection tube cannot

touch each other.

• The top cover of the outdoor unit and the electrical

box assembly should be fixed by the screw.

Otherwise, it can cause a fire or a short circuit

caused by water or dust.

• Use a UL-approved electrical branch circuit

disconnect for providing supply voltage to the split

system outdoor unit. Locate the disconnect within

sight and readily accessible per NEC and local

codes.

Installation Instructions

INSTALLATION (cont.}

| INSTALL THE OUTDOOR UNIT

• Install the connection tube

i. Align the center of the tubing flare with the

relevant valve.

2. Screw in the flare nut by hand and then tighten

the nut with spanner and torque wrench. See

the table below for the correct torque.

3. Connecting tube specifications are shown

below:

10,000/14,00020,000

Spedficetions BTU Units BTU Units

Design Length 20ft. 26.2ft.

ExtraRefrigerantCharge 0.16oz./ft. 0.54oz./ft.

PerFt.AboveDesignLength

Outer Diameter Liquid Pipe 1/4" 3/8"

Outer Diameter GasPipe 1/2" 5/8"

Max.Distance Height 33 ft. 33ft.

Max.Distance Length 68 ft. 98 ft.

NOTE: Exceeding tightening torque will damage

the copper tubing.

Tightening torque table

Tubing OD

1/4"

3/8"

1/2"

5/8"

Tighteningtorque(in./Ib.)

140-170

270-310

440-480

530-570

Flarenut

Joint

Spanner

uewrench

NOTE: To prevent wind and pest infiltration,

seal holes around the tubing and wiring with

the supplied sealer.

I-_ PURGE THE AIR AND

TEST FOR LEAKAGE

,

2.

3.

,

5.

Install the connecting tubes of the

indoor/outdoor unit.

DO NOT OPEN THE GAS VALVES UNTIL THE

EVACUATION PROCESSIS COMPLETE.

Remove the gas line service port cap and

connect the gas valves of the vacuum gauge,

vacuum pump and outdoor unit.

NOTE: Connect bg using a 1/4" Female x

1/2" Male Adapter Access Fitting (obtain Iocallg).

Start the vacuum pump. (Running time should

be more than 15 minutes.)

Check the vacuum with the vacuum gauge. The

gauge should read -30 in. Hg. After evacuation,

fulls close the handle on the manifold valve

(on the vacuum pump device). Then stop the

vacuum pump and disconnect it.

6. The pressure should be kept for 1-2 minutes

to confirm that the reading of the vacuum

gauge does not change. The pressure should

be-30 in. Hg.

7. Remove the vacuum line and replace the service

port cap.

8. Remove both the liquid and gas valve caps.

9. Open the gas and liquid valve entirelg, using

the 5 mm Allen wrench. If this is not done, the

performance will be reduced, or an error will

OCCUr.

i0. Replace the caps and tighten securelg.

(

Cap

Liquid_hp_

Gastube

Vacuumgauge

Vacuumpump

15

Installation Instructions

_-_ TEST OPERATION AND CHECK AFTER INSTALLATION

Test operation

1. Before test operation

• Do not switch on power before installation is finished completely.

• Electrical wiring must be connected correctly and securely.

• Shut-off valves of the connection tubes should be opened.

• All impurities such us scraps and particulates must be cleared from the unit.

2. Test operation method

• Switch on power and press the ON/OFF pod on the remote control to turn on the air conditioner.

• Press the MODE pad and check the operation conditions of each of the modes.

i0,000 and 14,000 BTU models onlg:

• If the remote control is lost, the emergency run operation can be performed with a ballpoint pen

or similar object.

a. When the unit is off, set the handling switch to the AUTO mode.

The unit will then automatically run in the mode selected by

the microcomputer system according to the surrounding

temperature. If you want to turn the unit off, press the

handling switch again.

b. When the unit is on, set the handling switch to the STOP mode to q

turn off the unit.

20,000 BTU models only:

• If the remote control is lost, open the front access panel and

perform the following:

a. Set the handling switch to the AUTO position to operate in the

AUTO mode. Once there is a remote control signal, the unit will

again be controlled by that signal.

b. Set the handling switch to the STOPposition to turn off the unit.

10,000and14,000BTUModels

20,000BTUModels

Handling

switch

Installation Checklist

Has the unit been securely installed? If not, the unit may full, shake or make noises.

Has the refrigerant leak test been performed? Leakage may cause insufficient cooling capacity.

Does the unit drain well? Poor drainage con cause condensation and dripping.

Is the voltage correct according to the nameplate? Incorrect voltage may cause electrical malfunction. Diagnostic

information is available for this unit. Contact your service technician.

Is the unit properly grounded? A nonsecure ground connection can cause damage.

Are the air inlet and outlet completely free of cover? Covering the air inlet or outlet may cause insufficient cooling

capacity.

Have the length of the connection tubing and refrigerant capacity been recorded? It is important to know these

things for future reference.

16

Before gou call for service... GEAppliances.com

Troubleshooting Tips:Save time and moneg! Review the chart below first and gou mag not need to call for service.

Possible Causes What To Do

The sgstem

does not start

The fuse is blown/circuit • Check the house fuse/circuit breaker box and

breaker is tripped, replace the fuse or reset the breaker.

The Timer operation is not set • Check the Timer functions and make sure they are

correctly, set to the desired settings.

The unit does not operate when .This is normal. Wait about ] minutes and the unit

restarted, will restart.

The sgstem does not Airflow is restricted. • Make sure there are no curtains, blinds or furniture

cool as it should blocking the front of the system.

The temperature control mag • Turn to a lower or higher setting. The lowest setting

not be set high or low enough, provides maximum cooling.

The air filter is dirty. • Clean the filter at least every ]0 days.

See the Operating Instructions section.

The room mag have been hot. .When the system is first turned on, you need

to allow time for the room to cool down.

Cold air is escaping. • Check for open furnace floor registers and cold air

returns.

The remote control The batteries are inserted • Check the position of the batteries. They should be

displag is faint or incorrectlg, inserted in the opposite (+)and (-) direction.

shows no displag

at all The batteries mag be dead. - Replace the batteries.

Normal Operating Sounds

m These sounds are common during the

antifreeze cooling or heating modes.

m You may hear a sound like water flowing. This

isthe sound of refrigerant flowing inside the

system.

m A noise that sounds like air being released is a

design feature of dehumidifying water being

processed inside the system.

m You may hear a clicking noise when you start

or stop the unit. This sound isthe expansion

or contraction of the unit due to changes in

the temperature.

17

Split Sgstem Warrantg.

All warrantg service provided bg our designated service network.

Toschedule service,call 866.404.5245. For service in Canada, contact

Gordon Williams Corp. at 1.888.209.0999. Pleasehave serial number

and model number available when calling for service.

Staple Four receipt here.

Proof of the origina! purchase

date is needed to obtain service

under the warrant F.

6E Will Replace:

Any part of the air conditioner which fails dueto a defect in materials or workmanship.

Duringthis limited one-year warranty, GEwill also provide,free of charge, all labor

and related serviceto replacethe defective part.

One Year

Fromthe dateof the

origina!purchase

Five Years

Fromthe dateof the

original purchase

Any part of the sealed refrigerating system (thecompressor,condenser,evaporator

and all connecting tubing) which fails due to a defect inmaterials or workmanship.

Duringthis four-year limited additional warranty, GEwill also provide,free of charge,

all labor and related serviceto replace the defective part.

Service trips to gout home to teach you how to use

the product.

Improper installation, delivers or maintenance. If Sou

have an installation problem, or if the air conditioner is

of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible for

providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including

failure to provide reasonable and necessary

maintenance.

In commercial locations labor necessary to move the

unit to a location where it is accessible for service by

an individual technician.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

Product not accessible to provide required service.

i XCLUSION OF IMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this Limited

Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for u particular

purpose, are limited to one year or the shortest period allowed bg law.

This warrant_l is extended to the original purchaser and an_l succeeding owner for products purchased

for home use within the USA and Canada. If the product is located in an area where service b!da GE

Authorized Servicer is not available, Sou may be responsible for a trip charge or Sou ma_l be required

to bring the product to an Authorized GE Service location for service. In Alaska, the warrantbt excludes

the cost of shipping or service calls to sour home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warrants

gives Sou specific legal rights, and Sou ma!d also have other rights which vary from state to state. To know

what Four legal rights are, consult btour local or state consumer affairs office or btour state's Attomebt

General.

Warrantor: General Electric Company. Louisville, KV 40225

18

Page is loading ...

Consumer Support.

GEAppliances Website GEAppliances.com

Havea question or need assistancewith your appliance?Try the GEAppliances Website 24 hours a day,

any day ofthe year! Forgreater convenience and faster service,you can now download Owner's Manuals,

order parts or even scheduleservice on-line.

Schedule Service GEAppliances.com

ExpertGErepair serviceisonly one step away from your door.Geton-line and schedule your serviceat

your convenience any day of the year! Or call 800.GE.CARES(800.432.2737)during normal businesshours.

RealLife Design Studio GEAppliances.com

GEsupports the UniversalDesignconcept-products, services and environments that can be usedby

people of all ages, sizesand capabilities.We recognizethe need to design for a wide range of physical and

mental abilities and impairments. Fordetails of GE'sUniversalDesignapplications, including kitchen designideas

for people with disabilities,check out our Website today. Forthe hearing impaired, pleasecall 800.TDD.GEAC

(800.833.4322).

Parts and Accessories

GEAppliances.com

Individualsqualified to servicetheir own appliances can have parts or accessoriessent directly to their homes

(VISA,MasterCordand Discovercards ore accepted).Orderon-line today, 24 hours every day or by phone at

800.626.2002during normal businesshours.

Instructions contained in this manual coverprocedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised,since improper

servicing may causeunsafe operation.

Contact Us

GEAppliances.com

Ifyou are not satisfiedwith the service you receivefrom GE,contact uson our Website with all the details

including your phone number,or write to: General Manager,Customer Relations

GEAppliances,Appliance Park

Louisville,KY/40225

l Register YourAppliance GEAppliances.com

Register your new appliance on-line--at your convenience! Timely product registration will allow for

enhanced communication and prompt serviceunder the terms of your warranty, should the need arise.

Youmay alsomail in the pre-printed registration card included inthe packing material.

Printed in China

GE AE0CD14DM0V1 Owner's manual

This manual is also suitable for

GE AE0CD14DM0V1 Owner's manual

in other languages

Related papers

Other documents