Icy Dock MB672SKGF-BB User manual

MB672SKGF

Screw-less Internal 3.5 “ SATA Enclosure w/ LCD

User Manual

Page is loading ...

English

3

B. After confirming the ʚ0ʛ mode, enter Temperature detection Setting mode.The LCD screen flashes the following:

C. If setting temperature at 55.0ʚ(131.0ʛ), the LCD will display the following:

•

Press “▲” to set the temperture to 55.0ʚ. Press and hold the “SET” button for more

than 3 seconds, and the alarm buzzer will sound “BEEP” twice as choice confirmed.

If sound “BEEP” is less than twice, it is not a confirmed choice.

Remark: If LCD screen does not return to Main Display, stop operation for 15 seconds, the LCD will then

automatically return to the Main Display and the original tempera ture detection setting will be cancelled.

•

Default setting: 50.0ʚ(122.0ʛ).

<4-3> HUTR Display

day hr

<4-4> HDD Access Display

To enter the HUTR mode, the Hour signal is displayed as below: If HDD is reading or writing, HDD access signal displays the below:

Шʳ

Ч

<4-2> Temperature Detection and ʚ0ʛ Settings:

A. From Main Display, press “SET” button to enter Temperature ʚ0ʛ!SettinMod and display the following:

•

Press ”▲” button or “ ▼” button to switch the ʚʈʛʈʚ/

•

Press “SET” button to confirm your choice.

English

Back Panel Description

5.

<4-5> Overheat from original Temperature Detection Setting

•

HDD access signal is displayed.

•

Fan and alarm buzzer signals

will continuously flash.

If the fan fails or is disconnected, the LCD displays the followingǺ

<4-6> Fan Fail Alarm

•

HDD access and Fan signals are

displayed.

•

Temperature and alarm buzzer

signals will continuously flash.

Original detection set at 50.0ʚ(122.0ʛ), if temperature

detected overheats the original setting. Screen using ʚ

will display the followingǺ

FAN FAIL

TEMP FAIL

HDD ACCESS

POWER LED

Master/Slave

SATA

4 PIN

Remark: Buzzer and alarm symbol are disabled by pressing any buttons located at the front panel.

4

English

5

PULL

HDD

A

B

STEP 1

STEP 2

STEP 3

STEP 4

HDD Installation

6.

English

6

1. ICY DOCK reserves the right to change or to upgrade any technical

specifications without prior notice.

2. ICY DOCK will not be liable for any software, hardware, and/or stored

data that may be become damaged or dysfunctional through the usage

of our product. ICY DOCK will only be responsible for repairing and

servicing its own product.

3. Due to specification differences between SATA I and SATA II hard drives,

the LED will only work with SATA II hard drives. To enable the

enclosure’s LED with SATA I hard drives, please refer to Note 4.

4. To allow the enclosure’s LED to work with SATA I hard drives, you will

need an optional HDD Access cable. Please connect the Access signal

pins provided on the backplane of the enclosure to the respective Host

Port’s Access signal pins. Please refer to your host port’s instruction

manual to locate its Access signal pins.

5. To determine if SATA II hard drives have built in HDD Access signal,

please refer to your HDD manufacture specifications.

6. To perform hot-swap function, the host side must also support hot-swap.

7. In the event that the LCD is not functioning properly, please reset the

LCD. If the problem persists, please contact the nearest ICY DOCK

support center.

8. For any further inquiries about ICY DOCK product or related product

information, please visit http://www.icydock.com.

Note:

Device Installation

7.

Page is loading ...

Deutsch

17

PULL

HDD

A

B

STEP 1

STEP 2

STEP 3

STEP 4

HDD Installation

6.

-

Page is loading ...

Icy Dock MB672SKGF-BB User manual

Icy Dock MB672SKGF-BB User manual

in other languages

Related papers

Other documents