Dell Force10 E1200i User guide

TeraScale to ExaScale Upgrade Procedure

The E-Series TeraScale is easily upgraded to Force10 Networks E-Series ExaScale. These upgrade requirements

outline the necessary components and procedures required to upgrade the E1200i with FTOS version 8.1.1.0.

Direct any questions regarding the upgrade to Force10 Networks’ Customer Support.

E-mail: [email protected]

Web: www.force10networks.com/support/

Telephone:

US and Canada: 866.965.5800

International: 408.965.5800

Supported Hardware

Hardware Catalog Number

Minimum Software

Version Required

E1200i Chassis

(Note 1)

CH-E1200I-AC

CH-E1200I-DC

8.1.1.1

AC Power Supply 2800W CC-E1200I-2800W-AC 8.1.1.1

DC Power Entry Module CH-E1200I-DC 8.1.1.1

Route Processor Module—ExaScale LC-EH-RPM 8.1.1.1

Switch Fabric Module

(Note 2)

CC-E-SFM3 8.1.1.1

10 port 10GE line card (10M CAM) LC-EH-10GE-10S 8.1.1.1

10 port 10GE line card (40M CAM) LC-EJ-10GE-10S 8.1.1.1

Fan Tray CC-E-1200I-Fan 8.1.1.1

Note 1: Do not mix AC and DC power supplies.

Note 2: E-Series ExaScale systems and FTOS Release 8.1.1.0 requires SFM version 752-00265-03 Rev

01 or higher. Use the

show sfm command to determine if your SFMs need to be upgraded.

Do not mix SFMs. All the SFMs in the chassis must run the required minimum software version.

TeraScale to ExaScale Upgrade Procedure 2

Upgrading Hardware

ExaScale SFM Requirements

E-Series ExaScale systems and FTOS Release 8.1.1.1 require SFM version 752-00265-03 Rev 01 or higher. Earlier

SFMs do not support line rate following the ExaScale 8.1.1.1 FPGA upgrade.

Do not mix SFMs. All the SFMs in the chassis must run the required minimum software version.

The automatic upgrade process takes place regardless of the SFMs you have installed. If you have one or more

SFMs that are earlier than 752-00265-03 Rev 01, a SYSLOG message (Message 1) appears during the upgrade .

The

show sfm command includes information for any SFM that needs to be upgraded (Figure 3).

FPGA Upgrades

FTOS version 8.1.1.1 introduces an automatic FPGA Upgrade process. It allows easy upgrades to newer SFM

version by implementing an auto-detection of mismatched SFM version. The upgrade to the mismatched SFMs is

done automatically.Manual upgrade are still supported for one or all SFMs.

Warning:

• Electrostatic discharge (ESD) damage can occur when components are mishandled. Always wear an

ESD-preventive ground strap when handling RPMs, SFMs, or line cards. After you remove the original

packaging, place RPMs, SFMs, and line cards on an antistatic surface.

• Do not supply power to your system until the PEM or Power Supply, Air Filter, Fan Tray are installed and

verified, and RPMs, SFMs, and line cards have been installed.

• To avoid chassis over-temperature condition, install blanks for RPMs, SFMs, and line card slots not in

use. Always replace cards or blanks immediately.

Message 1 SYSLOG messages during FPGA Automatic Upgrade

00:00:52: %RPM1-P:CP %TSM-5-SFM_OLDER_VERSION: Older version of SFM 8 detected

00:00:52: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 8

00:00:51: %RPM1-P:CP %TSM-5-SFM_OLDER_VERSION: Older version of SFM 7 detected

00:00:51: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 7

00:00:51: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 6

00:00:50: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 5

00:00:49: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 4

00:00:48: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 3

00:00:48: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 2

00:00:47: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 1

00:00:47: %RPM1-P:CP %TSM-5-SFM_FOUND: Found SFM 0

TeraScale to ExaScale Upgrade Procedure 3

Automatic upgrade during boot, reboot, reload, or restart

The FPGA auto upgrade takes place when any SFMs in the chassis run an FPGA version lower than the version

running during the boot, reboot, reload and restart operations. During the auto upgrade process, the system displays

messages relaying the status of the upgrade process (Figure 1). To verify the result of the SFM version upgrade, use

the

show sfm command.

Figure 1 FPGA Automatic Upgrade Messages

Verify the result of the SFM version upgrade using the show sfm command.

**************************************************************************

*

* Warning !!! Warning !!! Warning !!!

*

* -------------------------------------------------------------------------------------

*

* Starting auto upgrade of SFMs to newer version 0x0.0.3

* Please wait until upgradation of all 5 SFMS is complete.

*

* SFM will restart itself after upgradation of all 5 SFM is complete !

*

**************************************************************************

SFM 0/5 upgrade started

SFM 0/5 is upgraded to revision 0x0.0.3.

SFM 1/5 upgrade started

SFM 1/5 is upgraded to revision 0x0.0.3.

SFM 2/5 upgrade started

SFM 2/5 is upgraded to revision 0x0.0.3.

SFM 3/5 upgrade started

SFM 3/5 is upgraded to revision 0x0.0.3.

SFM 4/5 upgrade started

SFM 4/5 is upgraded to revision 0x0.0.3.

*************************************************************

*

* Warning !!! Warning !!! Warning !!!

*

* -----------------------------------------------------------

*

* Auto upgrade on all 5 SFM to version 0x0.0.3 is complete.

*

* Rebooting chassis .... !!!

*

*************************************************************

TeraScale to ExaScale Upgrade Procedure 4

Automatic upgrade for one or more new SFMs

The FPGA auto upgrade takes place when any newly inserted SFM runs an FPGA version lower than the version

running on the SFMs in the chassis. During this auto upgrade process, the system displays messages relaying the

status of the upgrade process (Figure 2). To verify the result of the individual SFM version upgrade, use the

show

sfm slot

command.

Figure 2 New SFM Automatic Upgrade Messages

**************************************************************************

*

* Warning !!! Warning !!! Warning !!!

*

* -----------------------------------------------------------------------

*

* Starting auto upgrade of SFMs to newer version 0x0.0.3

* Please wait until upgradation of 1 SFM is complete.

*

* SFM will reset itself after upgradation of 1 SFM is complete !

*

**************************************************************************

SFM 0/9 upgrade started

SFM 0/9 is upgraded to revision 0x0.0.3.

*************************************************************

*

* Warning !!! Warning !!! Warning !!!

*

* -----------------------------------------------------------

*

* Auto upgrade on 1 SFM to version 0x0.0.3 is complete.

*

* Resetting SFM .... Please wait ....!!!

*

*************************************************************

SFM 0/9 reset started

00:08:29: %RPM1-P:CP %TSM-6-SFM_USR_RESET: SFM 0 reset by user

reset SFM 0 successful !

*************************************************************

*

* Warning !!! Warning !!! Warning !!!

*

* -----------------------------------------------------------

*

* Resetting on 1 SFM to revision 0x0.0.3 is complete !

*

*************************************************************

TeraScale to ExaScale Upgrade Procedure 5

TeraScale to ExaScale Upgrade

Be sure you have the correct ExaScale hardware ready for installation prior to beginning this upgrade. Refer to

Supported Hardware for the list of hardware required for E-Series ExaScale with FTOS 8.1.1.1.

Step Command Syntax Command Mode Purpose

1 Turn the On/Standby switch to

Standby (AC).

Turn the Remote Power Source to

Off (DC).

Power-off the chassis.

2 Replace the TeraScale RPMs, SFMs and linecards with ExaScale RPMs, SFMs and linecards.

Refer to the RPM, SFM and Linecard documentation for installation and replacement details.

3 Turn the On/Standby switch to

ON

(AC)

Turn the Remote Power Switch to

ON

(DC).

Power on the chassis

4

The chassis automatically powers up with a ExaScale image

if the RPM has been programmed to boot

from particular FTP location or Flash that points to a TeraScale image. If no image is configured, go to

Steps 5 and 6.

5

Ctrl+Shift+6

Stop the chassis in boot user mode and

configure it to boot from FTP or Flash

and reload.

6 boot change

{primary|secondary|default}

After entering the keywords and

desired option, press Enter. The

software prompts you to enter the

following:

• boot device (ftp, tftp, flash, slot0)

• image file name

• IP address of the server with the

image

• username and password (only for

FTP)

BOOT_USER Tell the system where to access the

ExaScale FTOS image used to boot the

system:

•Enter

primary to configure the boot

parameters used in the first attempt

to boot the system.

•Enter

secondary for when the

primary operating system boot

selection is not available.

Enter

default to configure boot

parameters used if the secondary

operating system boot parameter

selection is not available. The default

location should always be the internal

flash device (flash:), and a verified

image should be stored there.

7

reload

BOOT_USER Restart the chassis to boot with the

specified ExaScale image.

8

show chassis

EXEC Privilege We can confirm using the show chassis

command.

TeraScale to ExaScale Upgrade Procedure 6

Step Command Syntax Command Mode Purpose

Force10#show chassis

-- Manufacturing Info --

Chassis Type : E600i

Chassis Mode : ExaScale

Chassis Epoch : 10.4 micro-seconds

Chassis MAC : 00:01:e8:41:cb:36

Serial Number : TY000001140

Part Number : 7520023900

Vendor Id : 04

Date Code : 01012008

Country Code : 01

Product Rev : 03

TeraScale to ExaScale Upgrade Procedure 7

ExaScale to TeraScale Downgrade

Step Command Syntax Command Mode Purpose

1

chassis chassis-mode terascale

EXEC Privilege Change the chassis mode to TeraScale.

2 Turn the On/Standby switch to

Standby (AC).

Turn the Remote Power Source to

Off (DC).

Power-off the chassis.

3 Replace the ExaScale RPMs, SFMs and linecards with TeraScale RPMs, linecards and SFMs.

Refer to the RPM, SFM and Linecard documentation for installation and replacement details.

4 Turn the On/Standby switch to

ON

(AC)

Turn the Remote Power Switch to

ON

(DC).

Power on the chassis

The chassis automatically powers up with a TeraScale image

if the RPM has been programmed to boot

from particular FTP location or Flash that points to a TeraScale image. If no image is configured, go to

Steps 5 and 6.

5

Ctrl+Shift+6

when prompted

during boot mode

Stop the chassis in boot user mode and

configure it to boot from FTP or Flash

and reload.

6 boot change

{primary|secondary|default}

After entering the keywords and

desired option, press Enter. The

software prompts you to enter the

following:

• boot device (ftp, tftp, flash, slot0)

• image file name

• IP address of the server with the

image

• username and password (for FTP)

BOOT_USER Tell the system where to access the

TeraScale FTOS image used to boot the

system:

•Enter

primary to configure the boot

parameters used in the first attempt

to boot the system.

•Enter

secondary for when the

primary operating system boot

selection is not available.

Enter

default to configure boot

parameters used if the secondary

operating system boot parameter

selection is not available. The default

location should always be the internal

flash device (flash:), and a verified

image should be stored there.

7

reload

BOOT_USER Restart the chassis to boot with the

specified TeraScale image.

Force10#chassis chassis-mode terascale

Chassis mode changed to TeraScale mode. Please reload chassis now.

System configuration has been modified. Save? [yes/no]: y

Proceed with reload [confirm yes/no]:y

TeraScale to ExaScale Upgrade Procedure 8

8

show chassis

EXEC Privilege We can confirm using the show chassis

command.

Step Command Syntax Command Mode Purpose

Force10#show chassis

-- Manufacturing Info --

Chassis Type : E1200

Chassis Mode : TeraScale

Chassis Epoch : 10.4 micro-seconds

Chassis MAC : 00:01:e8:05:db:05

Serial Number : 7520010900

Part Number : 0

Vendor Id : 04

Date Code : 11252003

Country Code : 01

Product Rev : 02

Dell Force10 E1200i User guide

This manual is also suitable for

Dell Force10 E1200i User guide

Related papers

Other documents