Eldes EKB3 User manual

Page is loading ...

EN | DE | FR | ES | PT

EN

FR

DE

ES

PT

EKB3 is a wired keypad that is compaible with ELDES

alarm systems ESIM364 and ESIM264. The device

comes equipped with LED indicators, rubber push-but-

tons (keys) and a variety of funcions, such as arming/

disarming, PGM output control (turn ON/OFF), violated

zone bypass, system seing coniguraion etc.

EKB3 ist eine Tastatur, die mit den ELDES Alarmsyste-

men ESIM364 und ESIM264 kompaibel ist. Das Gerät

ist mit LED-Anzeigen, Gummitasten und einer Vielzahl

von Funkionen ausgestatet, zB Scharfschalten / Deak-

ivieren, PGM-Ausgang (Ein- / Ausschalten), Umgehen

einer verletzten Zone, Konigurieren der Systemeinstel-

lung etc.

EKB3 est un clavier ilaire compaible avec les systèmes

d’alarme ESIM364 et ESIM264. L’appareil est équipé

de voyants LED, de boutons poussoirs (touches) et

d’une variété de foncionnalités comme l’armement/

désarmement, le contrôle d’une sorie PGM (ON/OFF) le

contournement de zone violée, le réglage des conigura-

ions du système...

EKB3 es un teclado compaible con los sistemas de

alarma ELDES ESIM364 y ESIM264. El disposiivo vie-

ne equipado con indicadores LED, botones con acabado

gomoso (teclas) y una variedad de funciones, como ar-

mado / desarmado, control de salida PGM (ENCENDIDO

/ APAGADO), poner en bypass zonas violadas, conigu-

ración de ajustes del sistema, etc.

O EKB3 é um teclado com ios, compaível com siste-

mas de alarme ELDES ESIM364 e ESIM264. O dispo-

siivo vem equipado com indicadores LED, botões de

pressão de borracha (teclas) e uma série de funções,

como armar/ desarmar, controlo de saída PGM (ligar/

desligar), desvio de zona violada, coniguração das dei-

nições do sistema, etc.

Page is loading ...

5

EN | DE | FR | ES | PT EN | DE | FR | ES | PT

3

4

EKB3

ESIM364/ESIM264

COM

#1 #2 #3 #4

Z1

Z2

Y

G

Y

G

AUX-

AUX+

AUX-

AUX+

3 2 13 2 1 3 2 1 3 2 1

Page is loading ...

7

EN | DE | FR | ES | PT EN | DE | FR | ES | PT

EKB3

NO

COM

Magnet

COM

Z1

Z2

Y

G

AUX-

AUX+

5,6kΩ

7

ELDES

Configuration Tool

LED KEYPAD EKB3 8 EN

EN

1 . GENERAL OPERATIONAL DESCRIPTION

MAIN FEATURES

• Arming and disarming

• STAY-arming

• Violated zone bypass and bypassed zone acivaion

• System coniguraion

• PGM output control

• Back-light

• Visual indicaion by LED indicators

• Audible indicaion by built-in buzzer

EKB3 is a wired accessory intended for ELDES alarm systems

ESIM364 and ESIM264. This keypad comes equipped with 16

keys and 18 LED indicators and a buzzer for audio indicaion.

Typically, the coniguraion of the system by EKB3 keypad is

carried out by acivaing the Coniguraion mode using the

installer code and entering a valid coniguraion command using

the number keys

0

9

, key for conirmaion and key

*

to clear the characters that have been entered. Alternaively,

the user can wait for 10 seconds unil the keypad buzzer will

provide a long beep indicaing that the entered characters have

been cleared. By pressing any key on the keypad will result in

acivaion of the back-light lasing for 60 seconds ater the

last keystroke. When typing in the characters, each keystroke

is followed by a short beep of the keypad buzzer, while the red

indicator lights up relecing a respecive number key

0

9

that is being pressed when typing in a coniguraion command

(key

0

is indicated by red indicator “10”). Addiionally, the LED

indicators and the keypad buzzer indicate the alarm condiion.

EKB3 comes equipped with 1 zone terminal designed for passive

wired digital sensor connecion, such as magneic door contact,

and a tamper switch located on the back side of the device for

enclosure state supervision.

It is possible to connect up to 4 EKB3 devices to ESIM364 or

to ESIM264 alarm system. The maximum wire length is 100m

(328.08t).

LED KEYPAD EKB3

EN 9

FRONT

1 2 3

4 5 6

7 8 9

*

0 #

BACK

EKB3

COM

Z1

Z2

3 2 1

Y

G

AUX-

AUX+

TAMPER

DESCRIPTION

F1

Fuse model MINISMDC020F-2 0.2A

Z2

N/A

COM

Common terminal

Z1

Zone terminal

Y

RS485 interface data bus terminal (yellow wire)

LED KEYPAD EKB3 10 EN

DESCRIPTION

G

RS485 interface data bus terminal (green wire)

AUX

Negaive power supply terminal

AUX

Posiive power supply terminal

3, 2, 1

Keypad address pins

TAMPER

Switch for enclosure state supervision

DESCRIPTION

1st character for STAY-arming

1st character for violated zone bypass and

bypassed zone acivaion

1st character for Coniguraion mode acivaion or

deacivaion (only for ESIM364 v02.07.00 and up)

1st character for system fault list indicaion / 1st

character for violated high-numbered zone indicaion /

1st character for violated tamper indicaion

0

9

Command typing

4

1

Keypad pariion switch (only for ESIM364

v02.07.00 and up)

LED indicaion

Steady ON: pariion armed (only for ESIM364

v02.07.00 and up)

Flashing: pariion violated (only for ESIM364

v02.07.00 and up)

0

Simultaneous 4-pariion arming (only for

ESIM364 v02.07.00 and up)

LED KEYPAD EKB3

EN 11

DESCRIPTION

*

1st character for Coniguraion mode acivaion

and deacivaion (for ESIM364 up to v02.06.20;

ESIM264 all versions) / 1st character for keypad

pariion switch (if enabled; only for ESIM264) /

clear typed in characters

Typed in command conirmaion

INDICATION DESCRIPTION

(red)

Steady ON

System armed / exit delay in

progress

Flashing Coniguraion mode acivated

(green)

Steady ON

System is ready – no violated zones

and/or violated tampers exist

(orange)

Steady ON System faults exist

Flashing Violated high-numbered zone

(orange)

Steady ON Violated zone bypassed

112

(red)

Steady ON

Zone violated / coniguraion

command being typed in

2. KEYPAD ADDRESS

ELDES alarm system supports up to 4 EKB3 keypads, each

individually addressed. The keypad address is set by physically

changing the jumper posiion on the pins located on the back

side of the keypad

JUMPER

COMBINATION

3 2 1 3 2 1 3 2 1 3 2 1

ADDRESS

Keypad

#1

Keypad

#2

Keypad

#3

Keypad

#4

Alternaively, the keypad address of the connected keypad can

be viewed using ELDES Coniguraion Tool sotware.

LED KEYPAD EKB3 12 EN

3. EKB3 ZONE AND TAMPER

Upon successful EKB3 connecion process, the system adds 1

Instant-type keypad zone. By default, the keypad zone is disabled

and can be enabled by ELDES Coniguraion Tool sotware or any

other coniguraion method supported by ELDES alarm system.

The zone can be used for passive wired sensor connecion, such

as magneic door contact intended to be installed at the designated

entry/exit doors and used along with the keypad buzzer indicaing

the opening of the doors, while the system is disarmed. Once the

system is armed, triggering the connected sensor will result in

alarm condiion of the zone.

In case of tamper violaion, the alarm is caused regardless of

system being armed or disarmed. EKB3 comes equipped with a

built-in tamper switch intended for enclosure supervision. Once

the enclosure of EKB3 is tampered, the tamper switch will become

triggered. By default, this acion will be followed by alarm, resuling

in sending an SMS text message and/or phone call to the user. The

SMS text message contains the violated tamper name.

Once the keypad zone is enabled, it becomes

mandatory to connect the resistor of 5,6kΩ nominal

included in the product pack, otherwise the zone state

will remain in permanent alarm condiion.

Regardless if the tamper switch alone is to be used,

the keypad zone must be enabled and the resistor of

5,6kΩ nominal must be connected across Z1 and COM

connectors.

LED KEYPAD EKB3

EN 13

4. PARTITION CONTROL AND

INDICATIONS

The features described below are only available with the system

ESIM364 and requires keypad pariion switch funcion being

enabled.

EKB3 keypad can operate in one of the following modes:

• 2-pariion mode – This parameter determines whether the

keypad can operate only in one of the irst two system pariions

allowing to arm/disarm them and switch the keypad pariion

using the number keys

1 2

. This mode is selected by

default.

• 4-pariion mode – This parameter determines whether the

keypad can operate in one of the four system pariions allowing

to arm/disarm them, indicate arm/disarm status, pariion state

on number keys

4

1

and switch the keypad pariion using

the number keys

4

1

.

Switching Keypad Pariion

To switch the keypad pariion, please press and hold key

1 2

(2-pariion mode) / key

4

1

(4-pariion mode)

for 2 seconds to apply the command. Upon the successful keypad

pariion change, the keypad buzzer will emit three short beeps.

In Case of Alarm

• 2-pariion mode – Red indicator will light ON indicaing the

corresponding violated zone number (Z1-Z12) or indicator will

lash or light ON indicaing the violated high-numbered zone

(Z13 and up) or tamper respecively.

• 4-pariion mode – Key

4

1

will lash, corresponding the

pariion that contains violated zone/tamper. By switching to

the violated pariion, the keypad will indicate the violated zone/

tamper number as described in “2-pariion mode”.

Arming and Disarming

To arm the pariion the keypad is switched to, please enter a valid

user/master code, assigned to the appropriate pariion.

• 2-pariion mode – The armed pariion number will be

indicated by illuminated indicator on indicators‘ secion A or B

corresponding pariion 1 or 2 respecively.

• 4-pariion mode – The armed pariion number will be

indicated by illuminated key

4

1

.

LED KEYPAD EKB3 14 EN

To arm all 4 pariions simultaneously, please follow these steps:

1. Press and hold key

0

.

2. Keep holding the key unil you hear three short beeps.

3. Release the key and enter a valid user/master code, assigned

to all 4 pariions.

4. Upon the successful arming process, keys

1

,

2

,

3

and

4

will light up.

Simultaneous arming of 4 pariions is supported by

4-pariion mode only.

5. TECHNICAL SPECIFICATIONS

Compaible with:

• ESIM364 v02.06.01 and up.

• ESIM264 v07.14.02 and up

Supply voltage 12-14V == 100mA max

Zone connecion type NC (normally-closed) / NO

(normally-open)

Maximum supported wire

length

100 m (328.08t)

Range of operaing

temperature

-30...+55°C (-22... +131°F).

Humidity 0-90% RH @ 0... +40°C (0-

90% RH @ +32... +104°F)

Dimensions 145x80x31mm

(5,71x3.15x1.22in)

LED KEYPAD EKB3

EN 15

TERMS OF USE

The following terms and condiions govern use of the EKB3 device

and contains important informaion on limitaions regarding the

product’s use and funcion, as well as informaion on the limitaions

of the manufacturer’s liability. Please carefully read these terms and

condiions. For more informaion on your product, please visit elde-

salarms.com

TECHNICAL SUPPORT

In order to ensure coninuous and proper operaion of the

EKB3 device and uninterrupted service, it is the responsibili-

ty of the User to make sure that: (I) the product is properly in-

stalled, and (II) there is constant electrical supply. For complete

system coniguraion and control using EKB3 keypad, please

refer to ELDES alarm system installaion manual located at

eldesalarms.com

If you experience diiculty during the installaion or subsequent use

of the system, you may contact “ELDES, UAB” distributor or dealer

in your country/region. For more informaion see eldesalarms.com

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines in order to maintain

safety of operators and people around:

• DO NOT use the device where it can cause potenial danger and

interfere with other devices – such as medical devices.

• DO NOT use the device in hazardous environment.

• DO NOT expose the device to high humidity, chemical environment

or mechanical impact.

• DO NOT atempt to repair the device yourself – any repairs must

be carried out by fully qualiied personnel only.

• Disconnect the mains power before installing. NEVER install or

carry out maintenance during stormy weather.

• EKB3 can be powered by a 12-14V == 150mA DC power supply

unit. Please use the power supply that meets the EN 60950-1

standard. Any addiional device you connect to the system, such

as a computer, must also be powered by an EN 60950-1 approved

supply. When connecing the power supply, mind the polarity

terminals. DO NOT switch the polarity terminals places. The

main circuit should be protected by short circuit or over-current

protecion.

• To switch the device of, power down any linked device that EKB3

is powered from or unplug the external electric power supply. A

blown fuse cannot be replaced by the user. The replacement fuse

has to be of the kind indicated by the manufacturer (fuse F1 model

– MINISMDC020F-2 0.2A).

LED KEYPAD EKB3 16 EN

• The device is not meant for outdoor use, i.e. you should use it

inside a building. Protect the device against cold, heat and keep

away from direct sunlight while in storage or operaion.

WARRANTY PROCEDURES

Warranty and out of warranty service should be obtained by

contacing the system integrator/dealer/retailer/e-tailer or distributor

where the customer purchased the product. When requesing for

service, the proof of purchase and the product serial number must

be provided. The return of the defecive product should be strictly

through the original route of purchase, and the customers shall

pack the product appropriately to prevent the returned product from

sufering in the transportaion.

MANUFACTURER WARRANTY

“ELDES, UAB” provides a limited warranty for its products only to the

person or enity that originally purchased the product from “ELDES,

UAB” or its authorized distributor or retailer and materials under

normal use of the system for a period of twenty four (24) months from

the date of shipment by the “ELDES, UAB” (Warranty Period). Warranty

obligaions do not cover expandable materials (power elements and/or

bateries), holders and enclosures. The warranty remains valid only if

the system is used as intended, following all guidelines outlined in this

manual and in accordance with the operaing condiions speciied. The

warranty is void if the system has been exposed to mechanical impact,

chemicals, high humidity, luids, corrosive and hazardous environments

or force majeure factors.

If a hardware defect arises and a valid claim is received within the

Warranty Period, at its own discreion, “ELDES, UAB” will either

(a) repair a hardware defect at no charge, using new or refurbished

replacement parts, or (b) exchange the product with a product that is

new or which has been manufactured from new or serviceable used

parts and is at least funcionally equivalent to the original product, or (c)

refund the purchase price of the product.

LIMITED LIABILITY

The buyer must agree that the system will reduce the risk thet,

burglary or other dangers but does not provide guarantee against such

events. “ELDES, UAB” will not assume any responsibility regarding

personal or property, or revenue loss while using the system.

“ELDES, UAB” shall also assume no liability due to direct or indirect

damage or loss, as well as unreceived income when using the system,

including cases, when the damages arise due to the above menioned

risks, when due to breakdown or malfuncion the user is not informed

in a imely manner about a risk which has arisen. In any case, the

liability of “ELDES, UAB”, as much as it is allowed by the laws in force,

Page is loading ...

LED KEYPAD EKB3

FR 29

FACE

1 2 3

4 5 6

7 8 9

*

0 #

DOS

EKB3

COM

Z1

Z2

3 2 1

Y

G

AUX-

AUX+

TAMPER

DESCRIPTION

F1

Modèle de fusible MINISMDC020F-2 0.2A

Z2 N/A

COM

Terminal commun

Z1

Terminal de zone

Y Terminal de l’interface data bus RS485 ( câble jaune)

Page is loading ...

LED KEYPAD EKB3

ES 39

FRONTAL

1 2 3

4 5 6

7 8 9

*

0 #

TRASERA

EKB3

COM

Z1

Z2

3 2 1

Y

G

AUX-

AUX+

TAMPER

DESCRIPCIÓN

F1

Fusor modelo MINISMDC020F 0.2A

Z2

N/A

COM

Terminal común

Z1

Terminal de zona

Y

Interfaz de datos RS485 terminal bus (cable

amarillo)

Page is loading ...

Made in the European Union

eldesalarms.com

Eldes EKB3 User manual

Eldes EKB3 User manual

in other languages

Related papers

Other documents