Innovative 7000-500-8408-248 Owner's manual

Category
Flat panel desk mounts
Type
Owner's manual
PAGE 1 OF 2
D
A
C
Thru-Desk
1 2 3
Desk Edge
1 12
D
E
F
3
E
F
OR
G
E
C
A
G
E
H
A
A
C
* Hardware not included.
2
Grommet Hole Side Bolt
8408-THRU 8408-CUP
A
C
800 524 2744 team-hat.com © 2022 Human Active Technology, LLC P509483 REV D
8408
Installation Instructions
PAGE 2 OF 2
A 3/8-16 Nylon Stop Nut 1
701418
B 3/8-16 x 1-1/4" Flat Socket Cap Screw 1
701855
C
Foam Pad
1
701565
Included with Models 8408 & 8408-thru only
D 3/8-16 x 7/8" Flat Socket Cap Screw 1
701799
E Rectangular Spacer 1
701544
F 1/2-13 x 3" Socket Set Screw 1
701126
G 3/8-16 x 2-1/2" Hex Head Bolt 1
700268
Included with Models 8408-thru & 8408-cup only
H
Foam Pad
1
701120
Included with Model 8408-cup only
I 7/32" Allen Wrench 1
701127
ITEM DESCRIPTION / PART NO. QUANTITY ITEM DESCRIPTION / PART NO. QUANTITY
PARTS LIST
© 2022 Human Active Technology, LLC P516629 REV B
7000
Installation Instructions
Human Active Technology
800 524 2744
customerservice@team-hat.com
team-hat.com
PAGE 1 OF 10
A Top Down Mount 1x
8524
B 180 Degree Rotation Stop 1x
108208-180
C M6 x 1 x 18mm Phillips Pan Head Screw 1x
105304
D Monitor Tilter 1x
8500 Tilter
E Quick Connect VESA Plate 1x
114808
F M4 x 12mm Phillips Pan Head Screw (4-pack) 1x
702096
G Dog Washer 1x
105189
H 10-32 x 3/8" FPhMS w/Lock Patch 1x
705198
I Forearm Cable Cap 1x
115584
J Cable Cap 1x
114810
K 1/8" Allen Wrench 1x
701312
L 3/32" Allen Wrench 1x
700146
M 7/32" Allen Wrench 1x
701127
Note: Parts may be shipped in separate boxes, please review all packaging prior to discarding.
PARTS LIST
PAGE 2 OF 10
M
A
OR
Desk thickness
up to 1.5" (3.8 cm)
Desk thickness
up to 1.5" (3.8 cm)
iIf the monitor arm or pole does not easily fit into the
mount, remove the bushing from the mount and place
it on the monitor arm or pole and press firmly back
into the mount.
OR
1 2
2a 2b 2c
7/32"
PAGE 3 OF 10
3
B
C
C
PAGE 4 OF 10
4
F
F
E
PAGE 5 OF 10
5
D
PAGE 6 OF 10
6
G
H
iTILTER FRICTION ADJUSTMENT
K
1/8"
PAGE 7 OF 10
7
7/32"
IMPORTANT!
• Monitor must be on arm
• Arm must be in mount
Depending on the weight of your monitor, you may have to make 15-20 turns.
If the arm drifts downward,
turn the adjustment screw
counter-clockwise.
If the arm drifts upward,
turn the adjustment screw
clockwise.
M
Press the arm down to
approximately parallel
with the desk prior to
turning the strength
adjustment screw.
In some instances, an additional
counterbalance adjustment may be
needed to allow the arm’s instant height
adjustment function to work properly.
If your arm is not staying in position
after performing step 7, tighten the
adjustment screw as shown.
1/8"
K
iOptional Adjustment
PAGE 8 OF 10
8
3/32"
L
PAGE 9 OF 10
9
J
I
PAGE 10 OF 10
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Innovative 7000-500-8408-248 Owner's manual

Category
Flat panel desk mounts
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI