ekwb EK-Quantum Vector² Strix RTX 3070 Ti D-RGB Installation guide

Brand: ekwb

Model: EK-Quantum Vector² Strix RTX 3070 Ti D-RGB

Category: Computer liquid cooling

Type: Installation guide

USER GUIDE

GPU WATER BLOCK

EK-Quantum

Vector² Strix RTX 3070 Ti D-RGB

Please note the installation of the product is intended to be undertaken

by an adequately trained and experienced person. You are installing the

product at your own risk. If you are not properly trained or experienced

or feel unsure about the installation procedure, please refrain from

installing the product yourself and contact our tech support for

assistance. We disclaim our liability for any damages to the product as

well as incidental, consequential, or indirect damages incurred due to

improper or inappropriate installation.

Before you start using this product, please follow these basic guidelines:

Carefully read the manual before beginning the installation

process.

Remove your graphics card from the computer for the safest

mounting process to prevent any possible damage to your

GPU or its circuit board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always

recommended for liquid cooling systems and mandatory for

nickel-plated water blocks!

Do not use pure distilled water! For best results, EK

recommends the use of EK-CryoFuel coolants!

To reach optimal performance, make sure to thoroughly

bleed the air out of your water block!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6

NICKEL PLEXI 6

PREPARING THE GRAPHICS CARD 7

REMOVING THE STOCK COOLER 7

PREPARING THE WATER BLOCK FOR INSTALLATION 7

CUTTING AND PLACING THERMAL PADS 8

APPLYING THERMAL COMPOUND 9

ATTACHING THE WATER BLOCK 9

PREPARING THE BACKPLATE 11

ATTACHING THE BACKPLATE 12

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

FITTINGS AND TUBING 13

CONNECTING THE D-RGB LED STRIP 14

TESTING THE LOOP 14

WARRANTY 15

SUPPORT AND SERVICE 16

SOCIAL MEDIA 16

- 4 -

BOX CONTENTS

4 mm

8 mm

EK-Loop Multi Allen Key (1 pc) Allen Key 2 mm (1 pc)

Allen Key 2.5 mm (1 pc)

Thermal Pad F 1.0 mm (6 pcs)

(3830046996732)

Thermal Pad F 1.5 mm (2 pcs)

(3830046996749)

Thermal Grease (1 pc)

EK-Quantum Vector2 Strix RTX 3070 Ti D-RGB

M2.5x4 AX1 Screw (8 pcs)

Terminal OR - Vector

14x1 mm (2 pcs)

120 mm

16 mm

120 mm

16 mm

Standoff Ø4.5/2.5 (1 pc)

Quantum Plug (2 pcs)

EK-Plug Out Spludger Tool (1 pc)

EAN: 104908

EAN: 104549

M2.5x8 AX1 Screw (1 pc)

Polyamid Washer M2.5 0.5mm (8 pcs)

- 5 -

WATER BLOCK DIMENSIONS

96 mm

124 mm

307 mm

142.5 mm

155.00 mm

27 mm

- 6 -

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS

NICKEL PLEXI

- Dimensions: (LxHxW): 307 x 155 x 27mm

- D-RGB cable length: 50cm

- D-RGB connector 3-pin 5V digital LED header (Pinout: +5V | Data |

Blocked | Ground)

Position EAN Description Quantity

1104334 Coldplate (Nickel) 1

2103947 FC Terminal (Acetal) 1

3104335 Top plate (Plexi) 1

4103962 Plexi insert 1

5104342 Backplate (Black elox) 1

6103987 Standoff M3.5-M2.5 x 3 mm 3

7103986 Standoff M3.5-M2.5 x 11.3 mm 6

8103988 Standoff M4-M2.5 x 3mm 4

9104188 Standoff ﬁ 4.5/2.5 6

10 104187 Screw M2.5 x 8 AX1 6

11 103971 Stand out (Acetal) 1

12 100663 EK - Badge 2

13 103964 Mylar sticker 2

14 8208 Screw M3 x 8 7991DIN 2

15 8311 Screw M4 x 20 DIN7984 3

16 104216 Disc magnet 3 x 3 2

17 103942 Terminal badge 1

18 5155 Terminal O-Ring 15 x 1 mm 2

19 104392 LED Cover (N. Elox) 1

20 104442 Main O-ring 148 x 2 mm 1

21 101556 LED D-RGB strip 500/300 mm 1

22 9013 Screw M4 x 8 DIN7984 14

23 104901 PCB cardboard 1

- 7 -

PREPARING THE WATER BLOCK FOR INSTALLATION

STEP 1

Unscrew six (6) Screws M2.5 x 8 AX1. Remove the backplate together

with six (6) Screws M2.5 x 8 AX1 and backplate standoffs. Standoffs

must stay on Screws M2.5 x 8 AX1. Remove cardboard. Save the

backplate for later steps.

Do not remove standoffs from screws! In case the

standoff detaches, replace it with a spare one. When

replacing the standoff make sure that you screw it on

the AX1 M2.5 x 8 screws. Do not push the standoff

onto the screw AX1 M2.5 x 8!

STEP 1

For this step, you will need:

Phillips Head Screwdriver

M2.5 x 8 AX1

SCREW

BACK PL ATE S TA ND OF F

DO NOT REMOVE

STANDOFFS

FROM SCREWS!

BACK PL AT E

PCB

CARDBOARD

PREPARING THE GRAPHICS CARD

REMOVING THE STOCK COOLER

Place your graphics card on the flat surface and carefully remove

the stock cooler. Do not forget to unplug all the LED and fan

connectors. Pay attention to the following steps in order to install

the EK-Quantum Vector2 Strix RTX 3070 Ti water block onto the

graphics card.

- 8 -

CUTTING AND PLACING THERMAL PADS

Your EK-Quantum Vector2 Strix RTX 3070 Ti D-RGB block comes

with Thermal Pads that have to be cut into smaller pieces to cover all

the VRM components. EK made sure to provide you with more than

an adequate quantity of Thermal Pads to complete this Step.

CAUTION: You must remove the protective foil from both

sides of the thermal pad before installation.

Replacement thermal pads:

Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

Thermal Pad F 1.5 mm – (120 x 16 mm) EAN: 3830046996749

For this step, you will need:

Scissors

Thermal Pad F – 1.0 mm (120 x 16 mm)

120 mm

16 mm

1 mm

STEP 2

The cardboard is printed in scale 1:1. Cut the Thermal Pads to the

size printed on the cardboard. Once cut to the size, Thermal Pads

should be placed on the GPU PCB, as shown in the picture.

STEP 2

Thermal Pad - 120 x 16 x 1.0 mm

STEP 1

F1 F1

Thermal Pad F – 1.5 mm (120 x 16 mm)

1.5 mm

120 mm

16 mm

- 9 -

Thermal Grease

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal

compound) on the GPU heat spreader – IHS – as shown in the

image. The layer of the thermal compound must be thin and even

over the entire surface of the IHS.

The excessive or uneven application of thermal grease

may lead to poor performance!

STEP 1

APPLYING THERMAL COMPOUND

For this step, you will need:

ATTACHING THE WATER BLOCK

STEP 1

Carefully position the water block with preinstalled standoffs on

the graphics card. During this process, make sure you have aligned

mounting holes of the PCB with holes of the water block.

Before attaching the PCB to the Water Block, make sure

all the Thermal Pads are placed correctly!

STEP 1

- 10 -

M2.5 PVC WASHER

Screws must be present in the places marked on the picture.

For this step, you will need:

Phillips Head Screwdriver

STEP 2

Use seven (7) M2.5 x 4 AX1 Screws and PVC washers to tighten

the PCB on the water block. Tighten the screws evenly using the

Phillips head screwdriver.

EK recommends you start tightening the screws around the GPU core

ﬁrst, and then continuing outward to prevent damage to the GPU.

STEP 2

M2.5 x 4 AX1 SCREW

- 11 -

PREPARING THE BACKPLATE

STEP 1

After attaching the water block, a few more thermal pads need to be

cut into smaller pieces to cover all the necessary components.

EK made sure to provide you with more than an adequate quantity of

thermal pads to complete this step.

CAUTION: You must remove the protective foil from both

sides of the thermal pad before installation.

Replacement thermal pads:

Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

Thermal Pad F 1.5 mm – (120 x 16 mm) EAN: 3830046996749

For this step, you will need:

Scissors

STEP 2

Apply the thermal pads onto the GPU PCB as shown in the image.

STEP 2

STEP 1

Thermal Pad - 120 x 16 x 1.0 mm

Thermal Pad - 120 x 16 x 1.5 mm

F1.5

Thermal Pad F – 1.0 mm (120 x 16 mm)

120 mm

16 mm

1 mm

Thermal Pad F – 1.5 mm (120 x 16 mm)

1.5 mm

120 mm

16 mm

F1.5 F1.5

F1.5

- 12 -

For this step, you will need:

Phillips Head Screwdriver

ATTACHING THE BACKPLATE

STEP 1

Place the backplate with six (6) M2.5 x 8 AX1 Screws and Standoffs

onto the PCB. Make sure all the holes are aligned.

Tighten the screws evenly using the Phillips head screwdriver

Before attaching the Backplate, make sure all the Thermal

Pads are placed correctly!

INSERTING THE GRAPHICS CARD INTO THE CHASSIS

Carefully lift your graphics card with the installed water block and

insert it into your PC’s motherboard PCI Express expansion slot.

Please keep in mind that your graphics card is heavier than before it

was equipped with the water block.

You need to be very careful when handling the graphics

card. Avoid all unnecessary manipulation of the water block

assembly that might damage your card or water block.

BACK PL AT E

- 13 -

FITTINGS AND TUBING

STEP 1

Screw-in two (2) G1/4 threaded male ﬁttings. Attach the liquid

cooling tubes and connect the water block to the cooling loop.

Do not forget to plug the remaining two openings using

the enclosed EK-Plug G1/4 or its equivalent.

EK recommends using EK ﬁttings with all EK water blocks.

CAUTION: When using connectors other than EK

ﬁttings, pay special attention to the length of the ﬁttings’

male G1/4” thread – 5mm is the maximum G1/4” thread

length allowed!

STEP 1

TUBING

EK- PLUG G1/4

EK-FITTING For this step, you will need:

EK-Loop Multi Allen Key

- 14 -

CONNECTING THE D-RGB LED STRIP

STEP 1

Plug the 3-pin connector of the distribution plate D-RGB LED

light to the D-RGB HEADER on the motherboard. The LED will

work if the pin layout on the header is as follows: +5V, Digital,

Empty, Ground.

Incorrect installation or installation to a wrong header can

damage the LED strip or the header itself!

STEP 1

D-RGB HEADER

RGB HEADER

To make sure the installation of EK components was successful, we

recommend you perform a leak test for 24 hours. When your loop

is complete and ﬁlled with coolant, connect the pump to a PSU

outside of your system. Do not connect power to any of the other

components. Turn on the PSU and let the pump run continuously.

It is normal for the coolant level to drop during this process as air

collects in the distribution plate. Inspect all parts of the loop, and

in the eventuality that coolant leaks, ﬁx the issue and repeat the

testing process. Ensure that all hardware is dry before the system is

powered on in order to prevent any damage.

TESTING THE LOOP

- 15 -

Our products are warranted against defects of materials and

quality for a period of 24 months, starting with the date of delivery

to the end-user. During this period, products will be repaired

or have parts replaced at our discretion, provided that 1) the

product is returned to the agent from whom it was purchased;

2) the product has been purchased by the end-user and has not

been used for commercial purposes; 3) the product has not been

misused, handled carelessly, or used in a manner other than the

way described in the instructions manual. This warranty does not

confer rights other than those expressly set out above and does not

cover any claims for consequential loss or damage. This warranty

is offered as an extra beneﬁt and does not affect your statutory

rights as a consumer. This warranty is voided if the product

comes in contact with aggressive UV additives or other improper

liquids. EK water blocks are sealed with a warranty-voiding circular

label, proving the water block has withstood a pressure leak test.

Removing the label will void the leak-free guarantee, but not the

guarantee on the product itself. Any other RMA issues can be

reported to EK Customer Support at www.ekwb.com/support

for further analysis.

WARRANTY

In case you need assistance or wish to order spare parts or a new

mounting mechanism, please contact:

https://www.ekwb.com/customer-support/

For spare parts orders, refer to the page with “TECHNICAL

SPECIFICATIONS AND WATER BLOCK PARTS” where you can ﬁnd

the EAN number of each part you might need.

Include the EAN number with quantity in your request. Mounting

Mechanism EAN can be found under “BOX CONTENTS”

Thermal pads are readily available in the EK shop

EKWaterBlocks

@EKWaterBlocks

ekwaterblocks

EKWBofﬁcial

SUPPORT AND SERVICE

SOCIAL MEDIA

ekwb EK-Quantum Vector² Strix RTX 3070 Ti D-RGB Installation guide

Brand: ekwb

Model: EK-Quantum Vector² Strix RTX 3070 Ti D-RGB

Category: Computer liquid cooling

Type: Installation guide

Download PDF

report

ekwb EK-Quantum Vector² Strix RTX 3070 Ti D-RGB Installation guide

ekwb EK-Quantum Vector² Strix RTX 3070 Ti D-RGB Installation guide

Related papers

Other documents