EVO Manufacturing EVO-600123K Installation guide

Brand
EVO Manufacturing
Model
EVO-600123K
Type
Installation guide
INS-J013
IMPORTANT: Read all instructions thoroughly from start to finish before
beginning the install. Check parts list and make sure all parts are included in the
kit. If the instructions are not properly followed severe frame, driveline and/or
suspension damage may result. Check for frame and suspension damage prior to
installation.
This kit does not require welding. Do not weld on any component. Welding may
void the warranty and/or cause the product to fail. If any parts are missing, or for
tech assistance; Contact King Off Road Racing Shocks: 714-530-8701
Most important after the install, Feel the difference and have fun.
Installation Instructions (Page 1)
2018 + Jeep Wrangler JL 2.5 Rear Shocks
King Shocks 12472 Edison Way Garden Grove, CA 92841
714-530-8701 www.kingshocks.com
Rear Parts List: Tools Required:
2 – 2.5 Rear Shocks (25001-374 0-2.5” Lift) OR Floor Jack/Jack Stands
2 – 2.5 Rear Shocks (25001-376 3-5” Lift) Metric Wrench/Socket Set
Standard Wrench/Socket Set
REAR: With the vehicle on level ground, block the front tires. Using a floor jack, raise the rear end and support
the frame rails with jack stands for safety. Remove tires. NOTE: Never work under an unsupported vehicle.
1. First remove the plastic cover behind the rear shock. Use an 8mm wrench or socket to remove the three screws and
remove the plastic piece.
INS-J013
IMPORTANT: Read all instructions thoroughly from start to finish before
beginning the install. Check parts list and make sure all parts are included in the
kit. If the instructions are not properly followed severe frame, driveline and/or
suspension damage may result. Check for frame and suspension damage prior to
installation.
This kit does not require welding. Do not weld on any component. Welding may
void the warranty and/or cause the product to fail. If any parts are missing, or for
tech assistance; Contact King Off Road Racing Shocks: 714-530-8701
Most important after the install, Feel the difference and have fun.
Installation Instructions (Page 2)
2018 + Jeep Wrangler JL 2.5 Rear Shocks
King Shocks 12472 Edison Way Garden Grove, CA 92841
714-530-8701 www.kingshocks.com
2. Keep a jack under the axle while removing and installing shocks; (For Non-Rubicon models: shocks have internal
rebound spring… you will need to jack the axle up a couple inches to take the tension off of the shock while removing lower
bolt.) First remove the lower nut using an 18mm socket and wrench. Jack the axle up and pull down on shock until you can
pull the bolt out by hand, Do Not attempt to run the bolt out with an impact without the axle being supported, you will
damage the threads and the axle will drop abruptly when the bolt comes out.
3. Remove upper bolt using an 18mm wrench or socket and remove shock.
INS-J013
IMPORTANT: Read all instructions thoroughly from start to finish before
beginning the install. Check parts list and make sure all parts are included in the
kit. If the instructions are not properly followed severe frame, driveline and/or
suspension damage may result. Check for frame and suspension damage prior to
installation.
This kit does not require welding. Do not weld on any component. Welding may
void the warranty and/or cause the product to fail. If any parts are missing, or for
tech assistance; Contact King Off Road Racing Shocks: 714-530-8701
Most important after the install, Feel the difference and have fun.
Installation Instructions (Page 3)
2018 + Jeep Wrangler JL 2.5 Rear Shocks
King Shocks 12472 Edison Way Garden Grove, CA 92841
714-530-8701 www.kingshocks.com
4. Install King Shocks so that the reservoir is facing towards the rear of the vehicle. Place the end cap into the
upper mount and install the factory bolt and tighten to 60 ft-lbs. Place the rod end into the lower mount, install
the factory bolt and nut and tighten to 60 ft-lbs.
INS-J013
IMPORTANT: Read all instructions thoroughly from start to finish before
beginning the install. Check parts list and make sure all parts are included in the
kit. If the instructions are not properly followed severe frame, driveline and/or
suspension damage may result. Check for frame and suspension damage prior to
installation.
This kit does not require welding. Do not weld on any component. Welding may
void the warranty and/or cause the product to fail. If any parts are missing, or for
tech assistance; Contact King Off Road Racing Shocks: 714-530-8701
Most important after the install, Feel the difference and have fun.
Installation Instructions (Page 4)
2018 + Jeep Wrangler JL 2.5 Rear Shocks
King Shocks 12472 Edison Way Garden Grove, CA 92841
714-530-8701 www.kingshocks.com
5. You will need to trim the plastic covers if you are reinstalling them. Cut out the section shown in the pictures
below and test fit. Trim plastic until it is not touching the shock and reinstall using the factory screws.
INS-J013
IMPORTANT: Read all instructions thoroughly from start to finish before
beginning the install. Check parts list and make sure all parts are included in the
kit. If the instructions are not properly followed severe frame, driveline and/or
suspension damage may result. Check for frame and suspension damage prior to
installation.
This kit does not require welding. Do not weld on any component. Welding may
void the warranty and/or cause the product to fail. If any parts are missing, or for
tech assistance; Contact King Off Road Racing Shocks: 714-530-8701
Most important after the install, Feel the difference and have fun.
Installation Instructions (Page 5)
2018 + Jeep Wrangler JL 2.5 Rear Shocks
King Shocks 12472 Edison Way Garden Grove, CA 92841
714-530-8701 www.kingshocks.com
DOUBLE CHECK ALL HARDWARE: Make sure everything is installed correctly and all hardware is tight before
reinstalling tires. Install tires; remove jack stands and lower vehicle to the ground. Recheck all hardware and lug nuts after
100 miles and periodically after that as part of routine maintenance.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

EVO Manufacturing EVO-600123K Installation guide

Brand
EVO Manufacturing
Model
EVO-600123K
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents