Sophos AP10 Operating Instructions Manual

AP10
Sophos
Brand
Sophos
Model
AP10
Category
WLAN access points
Type
Operating Instructions Manual

This manual is also suitable for

Sophos AP10 is a wireless access point designed to provide secure and reliable wireless connectivity for small businesses and home offices. It supports 802.11 b/g/n standards, offering speeds of up to 300 Mbps. The device can be easily mounted on a wall or ceiling, making it suitable for various environments. It features multiple LED indicators to provide real-time status information, including power, LAN connection, and WLAN access. The Sophos AP10 comes with a 1-year warranty and lifetime support, ensuring peace of mind for users.

Sophos AP10 is a wireless access point designed to provide secure and reliable wireless connectivity for small businesses and home offices. It supports 802.11 b/g/n standards, offering speeds of up to 300 Mbps. The device can be easily mounted on a wall or ceiling, making it suitable for various environments. It features multiple LED indicators to provide real-time status information, including power, LAN connection, and WLAN access. The Sophos AP10 comes with a 1-year warranty and lifetime support, ensuring peace of mind for users.

Operating Instructions
Sophos Access Points
2Sophos Access Point Operating Instructions
Content
Sophos AP10 03
Introduction 04
Controls 04
Placing into operation 05
Sophos AP10 mounting instructions 05
Technical specifications 06
Sophos AP30 07
Introduction 08
Controls 08
Placing into operation 09
Sophos AP30 mounting instructions 09
Power-over-Ethernet injector (optionally included with AP30) 09
Installing the PoE injector 10
Technical specifications 10
Sophos AP50 12
Introduction 13
Controls 13
Placing into operation 14
Sophos AP50 mounting instructions 14
Power-over-Ethernet injector (optionally included with AP50) 14
Installing the PoE injector 15
Technical specifications 16
3
Operating Instructions
Sophos AP10
4
Introduction
We are pleased to welcome you as new Sophos Access Point customer. To
install and configure the access, point may refer to the following documents:
Ì Sophos Access Points Security Notes & Regulatory Compliance: Notes on
access point security
Ì Sophos Access Points Quick Start Guide: System peripheral connection in
a few steps
Ì Sophos AP10 Operating Instructions: Notes on the commissioning of the
access point
Ì Sophos UTM/ASG Administration Guide: Configuring the UTM hardware &
software appliance
The instructions must be read carefully prior to using the device and should
be kept in a safe place. You may download all user manuals and additional
documentation from the Astaro Knowledgebase via:
www.astaro.com/kb.
Navigate to the main topics Manuals / Guides.
Controls
Power (LED display)
Off Power off
On continuously Power on
Blinking rapidly Firmware update
Blinking slowly No connection to the Sophos UTM
LAN connection (LED display)
On continuously Network connection, no activity
Blinking Network activity
WLAN access (LED display)
On continuously Network connection, no activity
Blinking Network activity
Interfaces and buttons
DC-IN Power
RJ45 10/100 Base-TX interface
Reset Currently not supported
Reset
10/100 Base-TX
Power
Sophos AP10 Operating Instructions
5
Placing into operation
Scope of supply
The supplied parts are indicated in the Sophos Access Points Quick Start
Guide.
Mounting instructions
All access points can be put on a stable horizontal surface or can be
mounted on the wall. Please take note of the following security hints:
Warnings and precautions
The access point can be operated safely if you observe the following notes
and the notes on the device itself.
General precautions
Review the electrical and general safety precautions that came with the
components you are adding to your access point. Allow the power supply
modules to cool before touching them.
Sophos AP10 mounting instructions
The Sophos AP10 can be mounted on the wall. Screws are not included in
delivery. Use only screws whose dimensions correspond with the mounting
holes on the back side.
Connection and configuration
How to connect the access point to the internal network is described in the
Sophos Access Points Quick Start Guide.
Sophos AP10 Operating Instructions
6
Technical specifications
Sophos AP10
LAN interfaces 1 x 10/100 Base-TX
Wireless interfaces 802.11 b/g/n 2.4 GHz
Antennas 1 x detachable dipole antenna
Power supply 100-240 VAC, 50/60 Hz, max. 0.3 A
Weight 130 g / 0.287 lbs
Dimensions W x H x D 124 x 25 x 96 mm
Chassis Plastic housing, white
Mounting Desktop / wall
Temperature 0°C to 45°C (operating)
-20°C to 70°C (storage)
10% to 95% relative humidity
non-considering
Certifications CE, FCC, VCCI, MIC, RoHS, WEEE
Sophos AP10 Operating Instructions
7
Operating Instructions
Sophos AP30
8
Introduction
We are pleased to welcome you as new Sophos Access Point customer. To
install and configure the access, point may refer to the following documents:
Ì Sophos Access Points Security Notes & Regulatory Compliance: Notes on
access point security
Ì Sophos Access Points Quick Start Guide: System peripheral connection in
a few steps
Ì Sophos AP30 Operating Instructions: Notes on the commissioning of the
access point
Ì Sophos UTM/ASG Administration Guide: Configuring the UTM hardware &
software appliance
The instructions must be read carefully prior to using the device and should
be kept in a safe place. You may download all user manuals and additional
documentation from the Astaro Knowledgebase via:
www.astaro.com/kb.
Navigate to the main topics Manuals / Guides.
Controls
Power (LED display)
Off Power off
On continuously Power on
Blinking rapidly Firmware update
Blinking slowly No connection to the Sophos UTM/ASG
LAN connection (LED display)
On continuously Network connection, no activity
Blinking Network activity
WLAN access (LED display)
On continuously Network connection, no activity
Blinking Network activity
Interfaces and buttons
Reset
Currently not supported
Ethernet 10/100 Base-TX interface
12 V DC IN Power
Power
10/100 Base-TX
Sophos AP30 Operating Instructions
9
Placing into operation
Scope of supply
The supplied parts are indicated in the Sophos Access Points Quick Start
Guide.
Mounting instructions
All access points can be put on a stable horizontal surface or can be
mounted on the wall. The Sophos AP30 can also be mounted on the ceiling.
Please take note of the following security hints:
Warnings and precautions
The access point can be operated safely if you observe the following notes
and the notes on the device itself.
General precautions
Review the electrical and general safety precautions that came with the
components you are adding to your access point. Allow the power supply
modules to cool before touching them.
Sophos AP30 mounting instructions
The Astaro AP30 can be mounted on the ceiling. Screws are included
in delivery. Use the screws from the scope of supply or screws whose
dimensions correspond with the mounting holes in the bracket.
1. Remove the bracket from the housing:
Unlock the bracket on the backside by turning it (approx. 5°) anticlockwise.
Then you can take off the bracket.
2. Mount the bracket on the ceiling:
Use the screws and anchors from the scope of supply.
3. Place the access point on the bracket:
Place the housing on the bracket and lock it by turning clockwise until stop.
Connection and configuration
How to connect the access point to the internal network is described in the
Sophos Access Points Quick Start Guide.
Power-over-Ethernet injector
(optionally included with AP30)
The PoE injector PD-3501/AC converts AC power to 50 V; DC power is then
provided over the Ethernet cable. This PoE injector supports up to 10/100
Mbps pass through data rates. The single port PD-3501/AC can be powered
via universal AC input and can provide up to 15.4 W.
Warning: Do not use cross over cable between the PoE injector PD-3501/AC
output port and the Access Point.
Sophos AP30 Operating Instructions
10
Note: Before placing the PoE injector:
Ì Do not cover the PoE injector or block the airflow to the PoE with any
foreign objects. Keep the PoE away from excessive heat and humidity and
free from vibration and dust.
Ì Ensure that the cable length from Ethernet network source to the AP30
does not exceed 100 m (330 ft). The PoE is not a repeater and does not
amplify the Ethernet data signal.
LED display
Off Power off
Yellow continuously Power on
Green continuously A remote terminal is connected
Green blinking Overload state or short-circuit
Interfaces
Input (Data In) 1 x 10/100 Base-TX
Output (Data & Power Out) 1 x 10/100 Base-TX, plus 50 VDC
Installing the PoE injector
1. Connect an Ethernet cable to the Data & Power Out interface.
2. Connect the other end of this Ethernet cable to the Ethernet interface of
the AP30.
3. Connect an Ethernet cable to the Data In interface.
4. Connect the other end of this Ethernet cable to your network switch.
5. Connect the AC power cord from the scope of supply to the
PD-3501/AC.
6. Connect the AC power cable to an AC outlet (100 – 240 VAC).
Technical specifications
Sophos AP30
LAN interfaces 1 x 10/100 Base-TX
Wireless interfaces 802.11 b/g/n 2.4 GHz
Antennas 3 x directional internal antennas
Power supply 100-240 VAC, 50/60 Hz, max. 0.5 A
Weight 230 g / 0.507 lbs
Dimensions W x H Ø 125 mm, height 60 mm
Chassis Plastic housing, white
Mounting Desktop / ceiling
Temperature 0 °C to 45 °C (operating)
-20 °C to 70 °C (storage)
5 % to 95 % relative humidity non-considering
Certifications CE, FCC , VCCI, MIC, RoHS, WEEE
LED
Data & Power Out
Data In
Power
Sophos AP30 Operating Instructions
11
PoE injector PD-3501/AC
LED display Power
Input power
AC input voltage: 90-264 VAC
AC input current: 0.5 A, 100-240 VAC
AC frequency: 47/63 Hz
Power over Ethernet
output (max.)
Output power voltage: 50 VDC
Output power: 15.4 W
802.3af compliant
Weight 200 g / 0.44 lbs
Dimensions W x H x D 53 x 33 x 140 mm
Chassis Plastic housing
Mounting Desktop / wall
Temperature 0°C to 40°C (operating)
-20°C to 70°C (storage)
10% to 90% relative humidity non-considering
Certifications CE, FCC, VCCI, UL, GS, RoHS, WEEE
Sophos AP30 Operating Instructions
12
Operating Instructions
Sophos AP50
13
Introduction
We are pleased to welcome you as new Sophos Access Point customer. To
install and configure the access, point may refer to the following documents:
Ì Sophos Access Points Security Notes & Regulatory Compliance: Notes on
access point security
Ì Sophos Access Points Quick Start Guide: System peripheral connection in
a few steps
Ì Sophos AP50 Operating Instructions: Notes on the commissioning of the
access point
Ì Sophos UTM/ASG Administration Guide: Configuring the UTM hardware &
software appliance
The instructions must be read carefully prior to using the device and should
be kept in a safe place. You may download all user manuals and additional
documentation from the Astaro Knowledgebase via: www.astaro.com/kb.
Navigate to the main topics Manuals / Guides.
Controls
Power (LED display)
Off Power off
On continuously Power on
Blinking rapidly Firmware update
Blinking slowly No connection to the Sophos UTM
LAN connection (LED display)
On continuously Network connection, no activity
Blinking Network activity
Wireless LAN access with 2.4 GHz (LED display)
On continuously Network connection, no activity
Blinking Network activity
Wireless LAN access with 5 GHz (LED display)
On continuously Network connection, no activity
Blinking Network activity
Interfaces and buttons
WPS button
Currently not supported
OI
Power on/off switch
DC 12V IN Power
Reset Currently not supported
PoE/LAN 10/100/1000 Base-TX interface
10/100/1000 Base-TX
Reset
Power
Power on/off switch
Sophos AP50 Operating Instructions
14
Placing into Operation
Scope of supply
The supplied parts are indicated in the Sophos Wireless Security Quick Start
Guide Hardware & Software.
Mounting instructions
All access points can be put on a stable horizontal surface or can be
mounted on the wall. Please take note of the following security hints:
Warnings and precautions
The access point can be operated safely if you observe the following notes
and the notes on the device itself.
General precautions
Review the electrical and general safety precautions that came with the
components you are adding to your access point. Allow the power supply
modules to cool before touching them.
Regulatory requirements
Sophos Access Points may not operate properly if they are not designed
for use in your country of operation. For example, an AP50 with the
supplementary model designation "FCC" (regulatory domain of the U.S.)
cannot be used in Europe. To ensure that the AP50 complies with your
country's regulatory requirements, always select the correct country of
operation.
Sophos AP50 mounting instructions
The Sophos AP50 can be mounted at the wall. Screws are not included in
delivery. Use only screws whose dimensions correspond with the mounting
holes on the back side.
Connection and configuration
How to connect the access point to the internal network is described in the
Sophos Access Points Quick Start Guide.
Power-over-Ethernet injector
(optionally included with AP50)
The PoE injector PD-9001GR/AC converts AC power to 55 V; DC power
is then provided over the Ethernet cable. This PoE injector supports up to
10/100/1000 Mbps pass through data rates. The single port PD-9001GR/AC
can be powered via universal AC input and can provide up to 30 W.
Warning: Do not use cross over cable between the PoE injector
PD-9001GR/AC output port and the Access Point.
Sophos AP50 Operating Instructions
15
Note: Before placing the PoE injector:
Ì Do not cover the PoE injector or block the airflow to the PoE with any
foreign objects. Keep the PoE away from excessive heat and humidity and
free from vibration and dust.
Ì Ensure that the cable length from Ethernet network source to the AP50
does not exceed 100 m (330 ft). The PoE is not a repeater and does not
amplify the Ethernet data signal.
LED display
Off Power off
Yellow continuously Power on
Green continuously A remote terminal is connected
Green blinking Overload state or short-circuit
Interfaces
Input (Data In) 1 x 10/100/1000 Base-TX
Output (Data & Power Out) 1 x 10/100/1000 Base-TX, plus 50 VDC
Installing the PoE injector
1. Connect an Ethernet cable to the Data & Power Out interface.
2. Connect the other end of this Ethernet cable to the Ethernet interface of
the AP50.
3. Connect an Ethernet cable to the Data In interface.
4. Connect the other end of this Ethernet cable to your network switch.
5. Connect the AC power cord from the scope of supply to the
PD-9001GR/AC.
6. Connect the AC power cable to an AC outlet (100 – 240 VAC).
LED
Data & Power Out
Data In
Power
Sophos AP50 Operating Instructions
Sophos Access Points Operating Instructions
United Kingdom Sales:
Tel: +44 (0)8447 671131
Email: [email protected]
North American Sales:
Toll Free: 1-866-866-2802
Email: [email protected]
Boston, USA | Oxford, UK
© Copyright 2011. Sophos Ltd. All rights reserved.
All trademarks are the property of their respective owners.
Sophos Operating Instructions 12.11v1.dNA
Technical specifications
Sophos AP50
LAN interfaces 1 x 10/100/1000 Base-T
Wireless interfaces 802.11 a/b/g/n 2.4 GHz or 5 GHz
Antennas 2 x 2.4G/5G dual-band antenna
Power supply 100-240 VAC, 50/60 Hz, max. 0.3 A
Weight 370 g / 0.816 lbs
Dimensions W x H x D 217 x 28 x 138 mm
Chassis Plastic housing, white
Mounting Desktop / wall
Temperature 0°C to 40°C (operating)
-20°C to 70°C (storage)
10% to 90% relative humidity non-considering
Certifications CE, FCC, RoHS, WEEE
PoE injector PD-9001GR/AC
Input power 100-240 VAC, 50/60 Hz, max. 0.8 A
Power over Ethernet
output (max.)
Output power voltage: 55 VDC
Output power: 30 W
802.3at compliant
Weight 200 g / 0.44 lbs
Dimensions W x H x D 53 x 33 x 140 mm
Chassis Plastic housing
Mounting Desktop / wall
Temperature 0°C to 40°C (operating)
-20°C to 70°C (storage)
10% to 90% relative humidity non-considering
Certifications CE, FCC, VCCI, UL, GS, RoHS, WEEE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Sophos AP10 Operating Instructions Manual

AP10
Sophos
Brand
Sophos
Model
AP10
Category
WLAN access points
Type
Operating Instructions Manual
This manual is also suitable for

Sophos AP10 is a wireless access point designed to provide secure and reliable wireless connectivity for small businesses and home offices. It supports 802.11 b/g/n standards, offering speeds of up to 300 Mbps. The device can be easily mounted on a wall or ceiling, making it suitable for various environments. It features multiple LED indicators to provide real-time status information, including power, LAN connection, and WLAN access. The Sophos AP10 comes with a 1-year warranty and lifetime support, ensuring peace of mind for users.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents