Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 1
MOTOROLA v3i DISASSEMBLY GUIDE
This guide will help you replace housing parts and get to the inner
parts of your phone. I am in no way responsible for any damage
occurred to your phone. If you follow what I say to do in this guide
you should be ok. But you need a lot of time and patience when
disassembling your phone.
YOU MUST READ EVERYTHING CAREFULLY!
!ONLY BUY HOUSINGS FROM CNN.CN, AS THEY ARE OEM!
Contents:
Steps 2~5,66 Facia Replacement.
Steps 2~5,55,56~63 Lcd Lens Replacement.
Step 24~42, 48~50,59~61 Aerial/Lower Front Housing Replacement.
Step 1~9,16~20,24~27,43,45~47,51 Keypad and Flex Replacement.
Step 1~8,10,12~14,56,66 LCD Replacement.
Tools Needed:
Screwdrivers ~ T3,T5,T6
Precision Tweezers
Mobile Phone Opening Tool
Brand new Glasses Cloth
Double Sided Tape
Screw Sizes:
LCD Housing Screws ~ T5 x 4
Rear Screws ~ T6 x 2
Lower Inner Housing Screws ~ T5 x 4
Rear Slip Screw ~ T3 x 1
BEFORE YOU DO ANYTHING MAKE SURE YOU HAVE ALL OF
THE TOOLS NEEDED.
You can buy these from eBay or any other mobile phone website.
Take your time and don’t rush! Move away any drinks or liquid, and
have good light.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 2
1. Turn off your v3i; remove the battery cover, battery, sim card, and
TF card.
2. Flick the rubber screw covers off with a small pin; make sure you
don’t loose these!
3. Now unscrew all four T5 Screws.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 3
4. Use your nail to lift up the top corner of the front facia (by the
camera) This should lift up easily.
5. Now use the mobile phone opening tool to slide down the edges
of the facia. Then lift up the bottom part if it doesn’t come away
freely.
6. Next remove the chrome buttons.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 4
Your phone should now look like this.
7. Flick up the left ribbon with your nail, or use tweezers.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 5
8. Next flick up the right hand (camera) ribbon.
9. Lift the bottom silver locking washers gently with tweezers. These
are at the bottom of the screen.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 6
10. Lift up the speaker at attached to the ribbon at the bottom of the
inner screen housing, gently ease them up.
11. Lift off the rubber camera surround with tweezers; just slide the
tweezers between the rubber and the housing. Then lift the
camera unit out.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 7
12. Now to remove the side buttons. Lift each button off with tweezers.
DO NOT CUT THE RIBBONS! You can use a pin to get behind
the stuck down ribbon if necessary.
13. Once all the buttons are unstuck and free from being stuck down.
Place the tweezers in the bottom of the right of the screen and
slowly start hinging it out. Keep lifting until it comes free.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 8
14. Lift the screen unit out of the inner screen housing.
15. Remove the grey rubber camera housing and the metal protector
to the right of it. Place this into the new housing.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 9
16. Flip the phone over and remove the T3 screw that holds in the left
flip.
17. Flip the phone open and the right small chrome flipper should pop
out. If this doesn’t place the tweezers in between the
thin bar on the chrome flipper and ease it out. Now
remove the small metal part and place this into your
new flipper part with tweezers. This is quite tricky.
18. Open the flip up on the phone and turn it over. Push the left larger
flipper out with a screwdriver. MIND THE RIBBON.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 10
19. Turn the phone over so the other flipper is facing you and place a
screwdriver on the small brass part, and push hard, push it in as
far as you can so that the small brass part pops out of the keypad
hinge.
You can then lift it out. WATCH THE RIBBON ON THE OPPOSITE
SIDE, DON’T SEVERE IT! Unhook the ribbon as soon as you can
from the left hinge.
20. From the outside push out the flicker using a screwdriver. Then
pull it out from the other side. Make sure you remove the flipper
and its black housing. Put this into the new housing.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 11
21. Dig out the small magnet to the right of the screen (YOU NEED
THIS PART ITS WHAT CHANGES THE SCREEN DISPLAY
WHEN YOU FLIP THE PHONE OPEN).
22. Remove the blue earpiece mesh and place it into the new housing
(make sure the stickiness is removed with the mesh).
23. Turn the screen housing over and remove the small silver M
emblem and stick it into place on the new housing.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 12
24. Get the main body of the phone and turn it over, now unscrew the
two T6 screws.
25. The aerial cover should separate slightly when lifted. Open it until
you can see the ribbon.
26. Pull the ribbon away from the board gently with tweezers.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 13
27. Push the bottom aerial housing away from the top this should
unclip the aerial cover from the lower mic housing. If not use the
mobile phone opening tool around the edge and it will lift up.
Your phone should now look like this.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 14
28. You now need to unscrew all four T5 screws that hold the lower
mic housing on.
29. Layout the screws and the metal antenna part as they were,
remove the lower housing and mic cover.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 15
30. Remove the rubber clip coverings on the aerial connector.
31. Place tweezers under the right hand side of the plastic aerial
cover, CAREFULLY SO YOU DON’T SCRATCH THE PCB! Lift it
up until it clicks and unclips itself. The rest should follow easily.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 16
32. Unhook the catch and push on the PCB from the opposite side
until the PCB comes free.
Your lower housing assembly should now look like this.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 17
33. Remove the speaker from the housing with tweezers.
34. Lift up the large rubber surround with tweezers.
35. Lift up the mesh below and place it into the new housing, then
place the rubber on top of it, and then put the speaker back in
place.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 18
36. Remove the gold screw contacts (at the top of the lower housing)
with tweezers, and place them into the new housing.
37. Now push the sim card holder so that the very bottom part unclips
to the opposite side.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 19
38. Now pull the left hand side of the sim card holder down at an
angle so it unclips.
39. Now unfree the sim card holder from the left hand side, it should
simply slide out once unclipped.
40. Place the sim card holder into the new housing, the bottom goes
in first, you might have to bend it slightly to get it in, just bend it
back to flat once finished. Place the small rubber bung in the new
housing.
Compiled Exclusively for MotoModders.net
Ajay16 Motorola v3i Disassembly Guide v1.0
Page: 20
Your lower housing should now look like this.
41. Get the PCB board and place it into the housing, push down
gently so that it slips in place.
42. Now get the plastic aerial covering and the aerial. Put one side in
and under the edge of the housing. Then bend out the opposite
side of the housing and let it clip in. Push down to make sure it’s
all slipped into place. Then replace the rubber parts.
Compiled Exclusively for MotoModders.net
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
