Fagor 3CC 239 EX Owner's manual

Montaje y modo de empleo

Instruções para montagem e utilização

Prescriptions de montage et mode d’emploi

Instruction on mounting and use

Montage- und Gebrauchsanweisung

Instrukce pro montá a pouití

Intrukcie k montái a pouitie

Montagevoorschriften en gebruiksaanwijzing

E

P

F

GB

D

CZ

SK

NL

Page is loading ...

Fijación distanciador de 3/4 cm. (operación 1). En caso de necesidad de desplazar hacia adelante el agujero

de salida, reposicionar la plantilla (operación 2) a 3 ó 4 cm. con especto a la parte posterior (tomando como base

la pared de fondo).

Fixation de la pièce intercalaire avec côté de 3 cm et de 4 cm (opération 1): s’il devait se révéler nécessaire

de déplacer à l’avant l’ouverture pour la conduite d’évacuation des fumées, positionner à nouveau le gabarit

(opération 2) à 3 ou 4 cm de la paroi qui se trouve à l’arrière.

Fixing the 3 cm and 4 cm spacers (operation 1): If the hole for the exhaust flue needs to be moved forward, reposition

the template (operation 2) to either 3 cm or 4 cm from the back wall

Befestigung des Abstandhalters mit Seitenmaßen 3 cm und 4 cm (Arbeitsschritt 1): sofern es sich nötig erweist,das

Bohrloch für das Rauchabzugsrohr vorderseitig (Arbeitsschritt 2) 3 oder 4 cm von der hinteren Wand ansetzen.

Fixação do espaçador de 3 e de 4 cm de lado (operação 1): no caso de ser necessário deslocar para a frente,

o furo destinado ao tubo de expulsão dos fumos, coloque de novo o molde em posição, (operação 2) a 3 ou

4 cm da parede de trás.

E

P

F

GB

D

Upevnìní rozpìrky 3-4 cm a nástropních svítidel.(operace 1): Pokud bude tøeba pøemístit smìrem

dopøedu otvor, který je tøeba vyvrtat na podvìsné èásti, umístíme ablonu na vrtání (operace

2) ve vzdálenosti 3 nebo 4 cm od zadní stìny.

CZ

Expulsión al exterior

Exaustão

Evacuation extérieure

Exhaust mode

Abluftversion

Verze pro vnìjí odsávání

Verzia pre vonkajie odsávanie

Versie met afvoer naar buiten

Aire en circulación

Recirculação

Recyclage

Filter mode

Umluftversion

Verze vyuívající recyklace

Verzia pouívajúca

recyklá

Versie met circulatie

Upevnenie ditanciátoru 3-4 cm a nástropných svietidiel (operácia 1).

Pokial bude treba premiesti dopredu otvor, ktorý je treba vyvrta na závesnej èasti, umiestíme

ablónu na vrtanie (operácia 2) vo vzdialenosti 3 alebo 4 od zadnej steny.

SK

Bevestiging van de afstandstukken van 3 cm en 4 cm (handeling 1): als de opening voor het afvoerkanaal vooruit

moeten worden bewogen, plaats de mal dan weer (handeling 2) op 3 cm of 4 cm van de achterwand.

NL

Page is loading ...

12

Hood Description - Fig. 1

1. Light Switch

2. Motor Speed Switch

3. Light Covers - illumination of the Cooking

Surface

4. Grease Filters

5. Grease Filter Support Grate (the grease filters

are located inside).

6. Light Cover Supports

7. Pull-Out Drawer

Using the hood

The hood is provided with several speeds. For

the best performance, we recommend using the

low speeds in normal conditions and the high

speeds in particular cases of strong odour and

vapour concentration.

Pull out the drawer to access the control panel.

We recommend starting up the hood a few

minutes before cooking and keeping it running

until all the odours have been eliminated.

Model with Self-supporting Metal

Filters

Removing the Grease Filters

- Fig. 2

a. Remove the pull-out drawer completely.

b. Press the side handles A towards the opposite

side and remove the filters.

Putting the Filters Back in Place

a. Remove the pull-out drawer completely and

mount the grease filter so that it covers the

drawer.

b. Close the drawer and install the remaining

grease filter.

Opening the Light Cover Support

- Fig. 2

a. Remove the pull-out drawer completely.

b. Push the B knobs inwards toward each other

(in the “Open” direction as indicated on the

plastic knob itself).

Model with Grease Filter Support

Grates

Opening the Grease Filter Support Grates

- Fig. 3

a. Extract the pull-out drawer completely.

b. Push the B knobs inwards toward each other

(in the “Open” direction as indicated on the

plastic knob itself).

c. To remove the grates completely, use the N

spring fasteners, which act as pins to hold the

grate in place (Fig. 4).

GB

Maintenance

Before performing any maintenance operation,

isolate the hood from the electrical supply by

switching off at the connector and removing the

connector fuse.

Or if the appliance has been connected through

a plug and socket, then the plug must be removed

from the socket.

Metal Grease Filter

The metal grease filter serves to trap grease

particles by suspending them.

The metal grease filter lasts forever and must be

washed either by hand or in the dishwasher

(65°C) with suitable detergents.

The grease filters must be washed at least

once a month.

Let the filter dry without damaging it before putting

it back into place.

Removing the Grease Filters (for models

wtih grease filter support grates)

a. Isolate the hood from the electrical supply.

b. Extract the pull-out drawer completely.

c. Open the grates that support the grease

filters.

d. Remove the L fasteners for the grease filter

and remove it (Fig. 5).

When washing the grease filter, wash the grate

as well with warm soapy water.

Carbon filter

This filter dissolves cooking odours.

The carbon filter must never be washed.

It should be changed every 4 months in

normal use.

Mounting the carbon filter:

a. Isolate the hood from the electrical supply.

b. Extract the pull-out drawer completely.

c. Remove the grease filters and open the light

cover support (or the grease filter support

grates).

d. Install the charcoal filter so that it covers the

plastic grate which protects the ventilation fan

(Fig. 6).

e. Turn the center handle of the carbon filter in

the clockwise direction until it locks in place.

f. Refit the grease filters and the light cover

support (or the grease filter support grates).

Removing the carbon filter:

Turn the center handle of the carbon filter in the

counterclockwise direction and remove the filter

from its seat

13

GB

Replacing the Lamp

a. Isolate the hood from the electrical supply.

b. Extract the pull-out drawer completely.

c. Open the light cover support or the rear

grease filter support grate.

d. Always replace burnt-out lamps with 40Watt

max. (E14).

e. Close the light cover support or the rear

grease filter support grate.

f. Before calling for customer service because

the lighting system does not work, make sure

that the lamps are screwed in tightly.

Cleaning

To clean the outside of the hood use a cloth

moistened with denatured alcohol or neutral liquid

detergents. Never use products containing

abrasive.

Wipe brushed stainless steel in the same direction

as the brushing to avoid scratching.

Attention

Failure to observe the rules for cleaning the

appliance and changing and cleaning the filters

may cause fires.

Therefore, we recommend observing these

instructions.

Use:Two systems are available

Exhaust mode

Vapours are extracted outside through an

exhausting pipe Ø120mm that is affixed to the

connection ring above the hood.

Diameter of the exhausting pipe must be equal to

that of the connection ring.

In the horizontal runs the duct must be slightly

slanted (about 10°) and directed upwards to vent

the air easily from the room to the outside.

Attention!

If the hood is supplied with carbon filter,

then it must be removed.

Filter mode

The air is cleaned by means of carbon filter (two

filters) and then circulated back into the room.

Attention!

If the hood is not supplied with carbon filter,

then it must be ordered and mounted.

This version is used when there is no exhaust

duct for venting outdoors or when it is impossible

to install one.

Installation

When installed, the distance between hood and

burners must be not less than 65 cm. above

electric burners or 75 cm. above gas or mixed-

fuel burners.

Warning!

— The hood cannot be connected to flues of

other appliances that run on energy sources

other than electricity.

— When the hood is used at the same time of

other appliances that run on energy sources

other than electricity, provision must be made

for an adequate supply of air.

— No food must be cooked flambé underneath

the hood.

The use of an unprotected flame is dangerous

for the filters and could cause fires.

Therefore, never use an open flame under the

hood. When frying foods, never leave the pan

alone because the cooking oil could flare up.

— Please, keep to the provisions of official

directives regarding the question of fume

discharge.

— The manufacturers refuse to accept any

responsibility for damage to the hood or its

catching on fire because of failure to observe

the above instructions.

Electrical connection

The electrical tension must correspond to the

tension noted on the label placed inside the

cooker hood. Connect the electrical plug, where

provided, to the an easily accessible outlet in

conformity with local standards in force.

Where an electrical plug is not provided (for direct

connection to electrical network) place a standards

approved bipolar switch with an aperture

distance of not less than 3mm (accessible) from

the contacts.

The manufacturers are not liable for any problems

caused by the user’s failure to observer the

above instructions.

Page is loading ...

LI1K1B Ed.07/2000

Fagor 3CC 239 EX Owner's manual

This manual is also suitable for

Fagor 3CC 239 EX Owner's manual

in other languages

Related papers

Other documents