EN 1
English
Important information
Safety
Ensure that your domestic mains supply voltage
matches the voltage indicated on the identication
sticker located at the back of your set. Where the
mains plug, AC inlet or an appliance coupler is used
as disconnect device, it shall remain readily operable.
On certain models, the light indicator is located at the
side of the TV set. The absence of a light indication
at the front does not mean that the TV set is fully
disconnected from the mains. To disconnect the TV
set completely, the mains plug must be pulled out.
The TV set’s components are sensitive to heat. The
maximum ambient temperature should not exceed
35º Celsius. Do not cover the vents at the back or
sides of the TV set. Leave sucient space around it to
allow adequate ventilation. Install the appliance away
from any source of heat (replace, etc.) or appliances
creating strong magnetic or electric elds.
Moisture in rooms where the set is installed should
not exceed 75% humidity. Moving the set from a cold
place to a warm one can cause condensation on the
screen (and on some components inside the TV set).
Let the condensation evaporate before switching the
TV set on again.
The or POWER/ button on the TV set or the
button on the remote control can be used to switch it
on and put it into standby mode. If you are not going
to be watching the TV for a lengthy period of time,
switch it o completely by removing the plug from the
mains power socket.
During thunderstorms, we recommend that you
disconnect the TV set from the mains and aerial so
that it is not aected by electrical or electromagnetic
surges that could damage it. For this reason, keep the
mains and aerial sockets accessible so they can be
disconnected, if necessary.
Unplug the TV set immediately if you notice it giving
o a smell of burning or smoke. You must never,
under any circumstances, open the TV set yourself,
as you run the risk of an electric shock in doing so.
WARNINGS
This appliance is intended for domestic household
use only and should not be used for any other
application, such as for non-domestic use or in a
commercial environment.
If the external exible cable or cord of this product is
damaged, it shall be replaced by the manufacturer or
his service agent or a similar qualied person in order
to avoid a hazard.
Leave more than 10cm clearance around the
television to allow adequate ventilation. The
ventilation should not be impeded by covering the
ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
The apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids, such as
vases shall be placed on the apparatus.
Batteries (battery pack or batteries installed) shall not
be exposed to excessive heat such as sunshine, re
or the like.
To reduce the risk of re or electric shock, do not
expose this apparatus to rain or moisture.
A television set may fall, causing serious personal
injury or death. Many injuries, particularly to children,
can be avoided by taking simple precautions such as:
• ALWAYS use cabinets or stands or mounting
methods recommended by the manufacturer of the
television set.
• ALWAYS use furniture that can safely support the
television set.
• ALWAYS ensure the television set is not
overhanging the edge of the supporting furniture.
• ALWAYS educate children about the dangers of
climbing on furniture to reach the television set or its
controls.
• ALWAYS route cords and cables connected to your
television so they cannot be tripped over, pulled or
grabbed.
• NEVER place a television set in an unstable
location.
• NEVER place the television set on tall furniture
(for example, cupboards or bookcases) without
anchoring both the furniture and the television set to
a suitable support.
• NEVER place the television set on cloth or other
materials that may be located between the television
set and supporting furniture.
• NEVER place items that might tempt children to
climb, such as toys and remote controls, on the top
of the television or furniture on which the television
is placed.
If the existing television set is going to be retained
and relocated, the same considerations as above
should be applied.
Equipment with this symbol is a Class II or
double insulated electrical appliance. It has
been designed in such a way that it does
not require a safety connection to electrical
earth.
Equipment without this symbol is a Class I
electrical appliance. It shall be connected
to a mains socket outlet with a protective
earthing connection.
To prevent the spread of re, keep candles
or other open ames away from this product
at all times.
EN 2
English
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
N
This symbol indicates that the fuse may
be in the neutral, and that the mains shall
be disconnected to de-energize the phase
conductors.
To prevent injury, this apparatus must be securely
attached to the oor/wall in accordance with the
installation instructions.
To reduce the risk of RF exposure, the use distance
of this apparatus should be at least 100cm.
If an outside antenna or cable system is connected to
the product, be sure the antenna or cable system is
grounded by a skilled person so as to provide some
protection against voltage surges and built-up static
charges.
TV screen
The TV screen used in this product is made of glass.
Therefore, it can break when the product is dropped
or impacted upon by other objects.
The TV screen is a very high technology product,
giving you nely detailed pictures. Occasionally, a few
nonactive pixels may appear on the screen as a xed
point of blue, green or red. This does not aect the
performance of your product.
Care
Use a glass-cleaning product to clean the screen and
a soft cloth and mild detergent to clean the rest of the
set.
Important: Using strong detergents, alcohol-based
and abrasive products may damage the screen.
Dust the vents at the back and sides regularly. Using
solvents, abrasive or alcohol-based products could
damage the TV set. If an object or liquid enters the
appliance, unplug it immediately and have it checked
by an authorized engineer. Never open the appliance
yourself since this may put you at risk or damage the
appliance.
ESD regulation
This apparatus meets ESD performance criteria.
In case the apparatus does not recover in Ethernet
connection mode or USB playing mode due to
electrostatic discharge, user intervention is required.
Bluetooth function notice
Bluetooth® technology (if available in your TV)
uses 2.4GHz frequency thus close proximity to Wi-
Fi access points, routers or microwave ovens might
interfere with Bluetooth audio streaming. If you face
Important information
interruptions in audio reception, you should restart
your Bluetooth device to nd frequency with less
interferences and if you continue to face issues you
should move closer to TV or increase space between
TV and source of interferences.
Bluetooth declaration ID: D056959
Hanging the TV set on the wall
Warning: This operation requires at least two
people depending on your TV dimension.
To ensure a safe installation, observe the following
safety notes:
• Check that the wall can support the weight of the TV
set and wall mount assembly.
• Follow the mounting instructions provided with the
wall mount. For certain models, make sure to screw
the hexagonal VESA wall mounting screw bosses
(and screws) provided with the set into the nuts for
the wall mount at the back of your set before your
wall mounting.
• The TV set must be installed on a vertical wall.
• Make sure to use only screws suitable for the
material of the wall.
• Make sure that the TV set cables are placed so that
there is no danger of tripping over them.
All other safety instructions about our TV sets are also
applicable here.
Multi product user manual
The features described in this manual are common to
most models. Some features may not be available on
your TV and/or your TV may include features that are
not described in this user manual. The illustrations in
this manual may dier from the actual product. Please
refer to the actual product.
Device update
Typically, some devices are updated quarterly, but not
always so specic. Some devices, especially those
that went on sale more than three years ago, will only
be updated if a critical vulnerability is found and xed.
EN 3
English
Figures and illustrations in this User Manual are provided for reference only and may dier from actual product
appearance. Product design and specications may be changed without notice.
Important information
Information for Users on Disposal of Old Equipment and Batteries
[European Union]
These symbols indicate that the electrical and electronic equipment and the battery with this
symbol should not be disposed of as general household waste at their end-of-life. Instead, the
products should be handed over to the applicable collection points for the recycling of electrical
and electronic equipment as well as batteries for proper treatment, recovery and recycling in
accordance with your national legislation and the Directive 2012/19/EU, 2006/66/EC and 2008/12/
EC.
By disposing of these products correctly, you will help to conserve natural resources and will help
to prevent potential negative eects on the environment and human health which could otherwise
be caused by inappropriate waste handling of these products.
For more information about collection points and recycling of these products, please contact your
local municipal oce, your household waste disposal service or the shop where you purchased
the product.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
[Business users]
If you wish to dispose of this product, please contact your supplier and check the terms and
conditions of the purchase contract.
[Other Countries outside the European Union]
These symbols are only valid in the European Union. If you wish to dispose of these items, please
do so in accordance with applicable national legislation or other rules in your country for the
treatment of old electrical equipment and batteries.
Notice:
The sign Pb
below the
symbol for
batteries
indicates that
this battery
contains lead.
Products
Battery
Declaration of Conformity
Hereby, TCL declares that the radio equipment type TV is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet address: www.tcl.com. Choose the model
name and go to DOWNLOADS.
Applies to products intended for the UK market.
Hereby, TCL declares that the radio equipment type TV is in compliance with the relevant UK statutory
requirements. The full text of the UK declaration of conformity is available at the following internet address: www.
tcl.com. Choose the model name and go to DOWNLOADS.
EN 4
English
Important information ………………………………… 1
Chapter 1 - Connections
Connect the power and antenna …………………… 5
Connect Blu-ray Disc player, HD game console, HD
camcorder, headphones, CI module ………………… 5
Connect to the Internet ……………………………… 6
Chapter 2 - Getting started
Exclusive Remote control …………………………… 7
Installing batteries …………………………………… 8
Switch the TV on and o ……………………………… 9
Initial setup …………………………………………… 9
Chapter 3 - Basic TV operations
Accessing channels ………………………………… 10
Watching connected devices ……………………… 10
Adjusting volume …………………………………… 10
Accessing Smart TV homepage ………………… 10
Using Settings menu ……………………………… 10
Chapter 4 - Using more of your TV
Installing channels ………………………………… 11
Common interface ………………………………… 11
Using the common interface module …………… 11
Accessing common interface services ………… 11
Using subtitles ……………………………………… 11
Turning on/o subtitles …………………………… 11
Enabling subtitle languages on digital TV
channels …………………………………………… 11
Selecting a subtitle type on digital TV channels 12
Using Teletext ……………………………………… 12
Selecting decoding page language …………… 12
Digital Teletext language ………………………… 12
External devices control (CEC) …………………… 12
Enabling or disabling CEC ……………………… 12
Power on the TV in sync ………………………… 12
Device standby in sync …………………………… 12
HbbTV ……………………………………………… 12
HbbTV access …………………………………… 12
HbbTV deactivation ……………………………… 13
Using EPG (Electronic Programme Guide) ……… 13
Bluetooth function…………………………………… 13
Quick start function ………………………………… 13
Networked waking up ……………………………… 13
Reset to factory default settings…………………… 14
Using the hands-free TV voice control …………… 14
Variable Refresh Rate ……………………………… 14
Apple AirPlay and HomeKit………………………… 14
Multi Visual ………………………………………… 15
Blue Light Filter ……………………………………… 15
Chapter 5 - Other information
Password in Parental Control ……………………… 16
Troubleshooting …………………………………… 16
Contents
EN 5
English
Connect the power and antenna
To switch on TV after connecting power cord, press or POWER/ .
Notes:
- Position of power socket varies according to TV model.
- Disconnect the power cord before connecting devices.
Cable
Chapter 1 - Connections
(Optical)
Digital
audio out
USB 3.0
5V 0.9A
MAX
LAN
(Service port)
HDMI 1 (4K@144Hz) HDMI 2 (4K@120Hz)
eARC/ARC
Antenna/Cable input Satellite input
13/18V 0.4A
MAX
AV adapter
Common interface
HDMI 3 (4K@60Hz) HDMI 4 (4K@60Hz)
HD game
console
Blu-ray Disc
player
HD Camcorder
Connect Blu-ray Disc player, HD game console, HD camcorder, headphones,
CI module
EN 6
English
Connections
Notes:
-Your TV might not have all connectors visible on diagram above. Number of USB and HDMI ports may vary
according to TV model.
-Button and connector locations may vary according to TV model.
-USB connectors are for data input from USB drives and for connecting other relevant USB devices where
applicable.
-All USB devices have to be directly connected to TV set without cable extenders. In case extender is
required, maximum 50cm length is recommended. Longer extenders should have ferrite beads.
-eARC/ARC (enhanced Audio Return Channel/Audio Return Channel) function is only supported on the HDMI
port identied with eARC/ARC. To use eARC/ARC function, please turn on CEC function rst as described in
the CEC section.
-It is recommended to use high quality and well shielded HDMI cables to avoid possible interferences.
-Please use headphones with 3.5mm TRS connector. Excessive sound pressure from headphones can cause
hearing loss.
Connect to the Internet
Wired connection
Wireless connection
Router
Modem Internet
LAN port
Modem Internet
Wireless router
Note: The following instructions are just the usual ways to connect your TV to the wired or wireless network.
The connection method may be dierent depending on your actual network conguration. If you have any
questions about your home network, please refer to your Internet service provider.
Network settings:
1. Press on the remote control to display the dashboard menu.
2. Select Settings and press OK to enter the settings menu.
3. Press / to select Network and Internet, press OK to enter the submenu and follow the on-screen
guidance to set up your network.
EN 7
English
Exclusive Remote control
Most of your television's functions are available via the menus that appear on the screen. The remote control
supplied with your set can be used to navigate through the menus and to congure all the general settings.
Chapter 2 - Getting started
To switch the sound o and back on.
Standby / quit standby.
Numeric buttons To enter channel numbers or a digit.
To select input source.
To display the Quick Settings panel.
Colour buttons To select tasks or Teletext pages; to be used for HbbTV
function.
To access User Center.
Press the Google Assistant button on your remote to talk to
the Google Assistant. (Available only in Google TV mode and
when the network connection is normal.)
To display the dashboard menu.
/ / / Navigation direction buttons.
OK To conrm an entry or selection. (Available to display the
channel list in TV mode.)
To return to the previous menu or quit an App.
To access the Smart TV homepage.
To access the Electronic Programme Guide (only available for
digital channels). Or access to DTV EPG. (Available only in
Google TV mode.)
VOL / To control the volume.
LIST To access DTV channel list.
* To access freeviewPlay.
To display programme information, if available.
CH / To change channels.
NETFLIX To access Netix if available.
prime video To access Prime video if available.
Youtube To access YouTube if available.
TCL CHANNEL To access TCL Channel.
TCL HOME To access TCL Home.
Web To access TCL BrowseHere.
Notes:
-This remote control is available only for selected models. The remote control
type may be changed without notice.
-The App buttons may dier depending on the model. The App button is used for
accessing the corresponding App.
-Follow the on-screen guide to pair the remote control with the TV when pressing
the Google Assistant button for the rst time.
-Google TV is the name of this device's software experience and a trademark of
Google LLC.
-The Google Assistant is not available in certain languages and countries.
EN 8
English
Getting started
CAUTION: Risk of re or explosion if the battery is replaced by an incorrect type.
Installing batteries
1. Push to open the back cover as illustrated.
2. Insert two AAA batteries according to the polarities marked on the batteries case.
3. Replace the back cover as illustrated.
Note: The remote control type may be changed without notice.
EN 9
English
Getting started
Important:
Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. Remove batteries when
the remote control is not to be used for a long time. Batteries left in equipment may cause damage through
deterioration and corrosive leakage, invalidating the guarantee.
To protect the environment use local recycling facilities for battery disposal. Dispose of used batteries
according to the instructions.
CAUTION: Risk of explosion if batteries are replaced by an incorrect type. Replace only with the same or
equivalent type recommended by the equipment manufacturer.
If the batteries in your remote control are run down, you can use the button on your TV set.
You can turn on the TV from standby mode by pressing the button on your TV set.
While the TV is on, the multi-function menu appears by pressing the button on your TV set. For more
information about how to use the multi-function menu, please refer to the figure below.
CH+ CH- Volume+ Source OKVolume-
Standby
Tips: Click to select options, press and hold to confirm.
• Press the button to move the highlight to the next function selection.
• Press and hold the button for more than 2 seconds to confirm your selection.
Note: Please refer to the Quick Start Guide to nd the button on your TV set.
Switch the TV on and o
1. When the power cord is connected, the TV will be turned on directly or be in standby mode. If the TV is in
standby mode, press the or POWER/ button on the set or the button on the remote control to turn it
on.
2. To put the TV into standby mode, press the button on the remote control. The TV set remains powered up,
but with low energy consumption.
3. To switch the TV o, unplug the mains plug from the mains outlet.
Note: In order to save energy and protect environment, certain models are designed with a relay switch. It is
normal phenomenon if you hear the sound of the relay when you turn on or o the TV set.
Initial setup
The rst time you switch the set on, the Welcome screen appears, which guides you through the initial setup
process. Follow the on-screen instructions to nish the initial setup process such as selecting the language,
connecting to the network, scanning channels, and more. During each step, either make a choice or skip the
step. If you skip a step, you can perform the setup later from the settings menu.
Note: If the channel search retrieved only the analogue channels it could be caused by poor broadcasting and
therefore is not covered by manufacturer warranty. Manufacturers cannot be held responsible for lack of
or poor broadcasting in some areas.
EN 10
English
Chapter 3 - Basic TV operations
Accessing channels
Using the Navigation Direction buttons: press
/ on the remote control to scroll through the
channels.
Using the OK button: press the OK button to display
the channel list and press / / / and OK to
select channels.
Using the CH / buttons: press the CH /
buttons on the remote control to scroll through the
channels.
Using the
LIST
button: press the
LIST
button on the
remote control to display the channel list and press /
/ / and OK to select channels.
Watching connected devices
Press on the remote control to display the source
list. Press
/
to select TV or other input sources and
press OK to conrm.
Note: Input sources like HDMI1 may not appear on
the source list, you can press button and
press
button till the end of the source list,
select Edit and press OK to turn the inputs
sources to ON, OFF or AUTO.
Adjusting volume
Volume control: press the VOL / buttons on the
remote control to increase or decrease the volume.
Sound mute: press the button to temporarily mute
the sound. Press this button again or the VOL
button to restore the sound.
Accessing Smart TV homepage
Allows you to enjoy Internet Applications (Apps) and
specially adapted Internet websites, and perform
system settings for your TV. You can make controlling
with the TV remote control.
WARNING:
• Congure the network settings before using Smart
TV applications.
• Slow responses and/or interruptions may occur,
depending on your network conditions.
• If you experience a problem using an application,
please contact the content provider.
• According to circumstances of the content provider,
an application’s updates or the application itself may
be discontinued.
• Depending on your country's regulations, some
applications may have limited service or not be
supported.
• Changes in application content may be made
without prior notice by the service provider.
1. Press on the remote control to display the Smart
TV homepage.
2. Press / / / and OK to enter the desired
Apps, functions or settings.
3. Press to return to the homepage.
Note: Since the connection with Internet takes
time, it’s recommended that you wait a few
minutes to use the Smart TV feature after
activation of TV from standby.
Using Settings menu
Allows you to adjust TV settings, such as picture and
sound.
1. Press on the remote control to display the
dashboard menu.
2. Select Settings and press OK to enter the settings
menu.
3. In submenus, press / to select menu options,
then press OK/ to enter the option list, or the
corresponding submenu, or press OK to toggle on
or o, or press / to adjust the setting.
4. Press to return to the previous menu.
EN 11
English
Chapter 4 - Using more of your TV
Installing channels
This section describes how to search and store
channels automatically. This may be done in any of
the cases below:
- you have skipped the channel installation step in the
initial setup;
- you are prompted that there are no channels in TV
mode;
- you want to update your channels.
1. In TV mode, press on the remote control
and select Settings > Channels and inputs >
Channel > Channel scan. Press OK/ to enter.
2. The TV installs and arranges channels according
to your country or region. Press / to select
Country/Region, and press OK/ to enter. Enter
the password you have set in the Settings >
System > Lock menu. Press / to select your
country or region and press OK to conrm.
3. Press / to select Automatic search and
press OK to enter.
4. Press / to select Tuner mode and press
/ to select Cable, Antenna or Satellite. (Note:
Satellite option is available only in selected
models.)
5. Press / to select other options to congure.
6. After conguration is completed, press to select
Search and press OK to start scanning channels.
7. The channel search may take a few minutes. After
the automatic search, channels are arranged in a
preset order. If you want to edit the channel list,
press on the remote control, select Settings
> Channels and inputs > Channel > Edit
Channels and press OK to enter.
Note: Edit Channels option is not available
when Tuner mode is set to Antenna and
Country/Region is set to United Kingdom.
Common interface
Encrypted digital TV channels can be decoded with a
common interface module and a card provided by a
digital TV service operator.
The common interface module may enable several
digital services, depending on the operator and
services you choose (for example, pay TV). Contact
your digital TV service operator for more information
about services and terms.
Using the common interface module
WARNING: Switch o your TV before inserting a
common interface module. Be sure to follow the
instructions described below. Wrong insertion of
a common interface module may damage both the
module and your TV.
1. Following the directions printed on the common
interface module, gently insert the module into the
common interface slot on the TV.
2. Push the module in as far as it will go.
3. Turn on the TV and wait for the common interface
function to be activated. This may take several
minutes.
Note: Do not remove the common interface
module from the slot. Removing the module
will deactivate the digital services.
Accessing common interface services
After inserting and activating the common interface
module, press on the remote control, select
Settings > Channels and inputs > Channel >
Common interface and press OK to enter.
This menu option is only available if the common
interface module is correctly inserted and activated.
On-screen applications and content are provided by
your digital TV service operator.
Using subtitles
You can enable subtitles for each TV channel.
Subtitles are broadcast via Teletext or DVB-T/DVB-C/
DVB-S/DVB-T2/DVB-S2 digital broadcasts. With
digital broadcasts, you have the additional option of
selecting a preferred subtitle language.
Turning on/o subtitles
1. Press on the remote control, select Settings >
Channels and inputs > Channel > Subtitle and
press OK/ to enter.
2. Select the Subtitle option, and press OK to toggle
between on or o.
3. Press to return to the previous menu.
Enabling subtitle languages on digital TV
channels
1. Press on the remote control, select Settings
> Channels and inputs > Channel > Subtitle >
Digital subtitle language 1st and press OK/ to
enter.
2. Press / to select a subtitle language as your
preferred language and press OK to conrm.
3. Press / to select Digital subtitle language
2nd and press OK/ to enter.
4. Press / to select a secondary subtitle
language and press OK to conrm.
5. Press to return to the previous menu.
EN 12
English
Using more of your TV
Selecting a subtitle type on digital TV
channels
1. Press on the remote control, select Settings
> Channels and inputs > Channel > Subtitle >
Subtitle type and press OK/ to enter.
2. Press / to select a subtitle type and press
OK to conrm. You can select Hearing impaired
to display the hearing impaired subtitles with your
selected language.
3. Press to return to the previous menu.
Using Teletext
Selecting decoding page language
1. Press on the remote control, select Settings
> Channels and inputs > Channel > Teletext >
Decoding page language and press OK/ to
enter.
2. Press / to select a proper type of language
in which Teletext will display and press OK to
conrm.
3. Press to return to the previous menu.
Digital Teletext language
On digital TV channels, depending on the
broadcaster, you may be able to enjoy a service with
multiple initial Teletext pages in dierent languages.
This function allows you to select an available
language as primary language, which relates to
dierent initial Teletext pages.
1. Press on the remote control, select Settings
> Channels and inputs > Channel > Teletext >
Digital teletext language and press OK/ to
enter.
2. Press / to select a language and press OK
to conrm.
3. Press to return to the previous menu.
External devices control (CEC)
Use this function to search for CEC devices connected
to the HDMI sockets in your TV and enable one-touch
play and one-touch standby between CEC devices.
Enabling or disabling CEC
1. Press on the remote control, select Settings
> Channels and inputs > Inputs > External
devices control (CEC) and press OK/ to enter.
1. Select the HDMI control option, and press OK to
toggle between on or o.
2. Press to return to the previous menu.
Power on the TV in sync
Enables the TV to automatically power on when you
power on a CEC device (e.g. DVD) with the device’s
remote. Press OK to turn it on to enable this function.
Device standby in sync
Enables all CEC devices to automatically go to the
standby mode when you turn o the TV with the TV
remote. Press OK to turn it on to enable this function.
Note: The CEC functions depend on the devices
connected and it is possible that some
devices may not interoperate correctly when
connected to this TV. The user manual or
the manufacturer of the problematic devices
should be consulted for further information.
HbbTV
HbbTV (Hybrid broadcast broadband TV) is a service
oered by certain broadcasters and available only on
some digital TV channels. HbbTV delivers interactive
television over broadband Internet. These interactive
features are added to and enrich the normal digital
programmes, and include services such as digital
teletext, electronic programme guide, games, voting,
specic information related to the current programme,
interactive advertising, information magazines, catch-
up TV, etc.
To use HbbTV please ensure your TV is connected to
Internet and HbbTV is switched on.
Notes:
-HbbTV services are broadcast- or country-
dependent and may be unavailable in your area.
-You cannot download les to your TV with
HbbTV function.
-Application provider or broadcasting related
conditions may cause an HbbTV application to
be unavailable momentarily.
-To access HbbTV applications you must connect
your TV to the Internet via a broadband link.
HbbTV applications may not work correctly in
case of network related issues.
HbbTV access
1. Press on the remote control, select Settings >
System > HbbTV settings and press OK/ Select
the HbbTV option, and press OK to turn it on.
2. When you tune to a digital TV channel that oers
HbbTV, this will be signalled to you by an on-
screen indication (generally a red button, but
other colour buttons may also be used). Press
the indicated colour button to open the interactive
pages.
3. Use / / / and the colour buttons to
navigate through the HbbTV pages and press OK
to conrm.
EN 13
English
Using more of your TV
HbbTV deactivation
To avoid disturbances that may be caused by HbbTV
broadcasting tests, you can turn o the HbbTV
function:
1. Press on the remote control, select Settings
> System > HbbTV settings and press OK/ to
enter.
2. Select the HbbTV option, and press OK to turn it
o to disable it.
Using EPG (Electronic Programme
Guide)
EPG is an on-screen guide that displays scheduled
digital TV programmes. You can navigate, select and
view programmes.
1. Press on the remote control, select Settings
> Channels and inputs > Channel > EPG and
press OK to enter, or press on the remote
control (if available), the Programme Guide menu
will appear, which allows you to get information
about the current or next programme playing
on each channel. Navigate through the dierent
programmes using the / / / buttons on the
remote control.
2. Use the related buttons shown at the left of the
screen to view EPG.
- Filter: Program guide lter for digital TV programs.
• Navigate through the dierent types using the /
buttons on the remote control.
• Select one or more types, which you want to
highlight from the type list, press OK to select or
deselect. A checkmark will appear to the left of the
type when selected.
- Schedule list: Press the OK button to enter, then
select Schedule reminder to set Channel, Date,
Reminder time and so on.
3. Press to return to the previous menu.
Bluetooth function
(* not available for some models)
Bluetooth® is a wireless technology standard for
exchanging data over short distance between
Bluetooth devices. You can connect Bluetooth audio
device, mouse or keyboard via the TV.
1. Press on the remote control, select Settings >
Remotes and accessories and press OK/ to
enter.
2. Select Pair accessory and press OK to enter.
The TV will search nearby Bluetooth devices
automatically. Select an available device, press
OK and follow the guides on the screen to connect
it.
Note: Bluetooth technology (if available in your TV)
uses 2.4GHz frequency thus close proximity
to Wi-Fi access points, routers or microwave
ovens might interfere with Bluetooth audio
streaming. If you face interruptions in
audio reception, you should restart your
Bluetooth device to nd frequency with less
interferences and if you continue to face
issues you should move closer to TV or
increase space between TV and source of
interferences.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use
of such marks by TTE Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
Quick start function
It enables you to turn on your TV faster from standby
mode than turning this function o, but it will also
increase standby power consumption.
1. Press on the remote control, select Settings >
System > Power and energy > Quick start and
press OK/ to enter.
2. Select the Quick start option and press OK to
toggle between on and o.
3. Press to return to the previous menu.
Networked waking up
This function allows you to turn on your TV from
standby mode via a network. To use this function,
please make sure:
1. Your TV is connected to an eective wireless home
network;
2. The desired controller, such as a smartphone, is
connected to the same wireless network as your
TV;
3. An App which supports networked waking up
function, such as Youtube, has been installed into
the controller;
4. In Google TV mode, press on the remote
control, select Settings > Network and Internet >
Networked standby and press OK to turn it on.
When the TV is in networked standby mode, you can
use the App to wake up the TV remotely.
Notes:
-This feature is disabled if you press and hold the
button on the remote control and conrm to
shut the TV down.
-Before using the feature of networked waking up,
make sure the Quick start function is enabled.
EN 14
English
Using more of your TV
-This function may not be available for certain
models.
-This feature is only available in Google TV mode.
Reset to factory default settings
Allows you to reset the TV to factory default settings.
1. Press on the remote control, select Settings
> System > About > Reset > Factory reset and
press OK to enter.
2. Select the Factory reset option and press OK to
enter. Then select Erase everything and press
OK to confirm.
3. Enter the password you have set or the PIN
according to the on-screen prompt.
4. Select OK and press OK to conrm.
5. The Welcome screen appears. Follow the
instructions in the section Initial setup.
Using the hands-free TV voice control
Before using the hands-free TV voice control, connect
the TV to the network and make sure it can access
the Google website rst. Then follow the steps below
to access.
1. Turn the built-in MIC switch (Please refer to the
Quick Start Guide to nd the MIC switch on your
TV set) to on before using this function.
2. In Google TV mode, Press on the remote
control.
3. Select "Yes, I'm in".
4. Say "OK Google" or "Hey Google" to activate it.
Notes:
-This hands-free TV voice control is only available
for selected models. For details, please refer to
your local dealer.
-A quiet surrounding is required for better function
when using it. The recommended distance for
using the hands-free TV voice control is within 2
meters in front of it.
-Turn the built-in MIC switch to o if you are not
going to use it.
-The availability of hands-free TV voice control
depends on your region/country/language.
-Turn on both Quick start and Screenless
service in the Settings > System > Power and
energy menu to enjoy hands-free voice control
in TV standby mode.
-Standby power consumption will increase
because the built-in MIC is always listening when
the Google Assistant or voice control with the
built-in MIC is enabled.
-This feature is only available in Google TV mode.
Variable Refresh Rate
Variable Refresh Rate is a feature that will allow
smooth gaming and eliminate screen tearing. The
refresh rate can dynamically change to up to 144Hz.
(Note: To use the function, Game Master needs to
be set to Auto or On in the System menu.)
This feature is available under source of HDMI1,
HDMI2, HDMI3 or HDMI4(the number of HDMI
socket on the TV will vary according to TV model).
Notes:
-4K@144Hz is only available on HDMI 1 (not
available in all models). PC Graphics card must
be able to output 144Hz, please check your
graphics card specications.
-4K@120Hz is only available on HDMI 1 or HDMI
2.
-Some models support refresh rate up to 120Hz.
-You need to make sure your Games Console or
PC support Variable Refresh Rate, and you may
need to check your games console settings to
activate the function.
-The game/content also will need to support
Variable Refresh Rate, and you may also need
to check the settings within the game.
Apple AirPlay and HomeKit
(* not available for some models)
Wirelessly share content with your TV using AirPlay
and control your TV using the Home app on your
iPhone, iPad, or Mac. You can set up AirPlay and
HomeKit at any time in Settings menu.
The function is enabled by default. To use the
function, make sure your iPhone, iPad, or Mac is iOS
or iPadOS device and the WiFi on the iOS or iPadOS
device is turned on. Then follow the steps below to
operate.
1. Press on the remote control, select Settings
> System > AirPlay and HomeKit Settings >
Apple AirPlay and HomeKit and press OK to
enter, or press (if available) on the remote
control, then select AirPlay > AirPlay and
HomeKit Settings and press OK to enter.
2. Press / to select the desired item and press
OK to enter the corresponding submenu.
3. Press to return to the previous menu.
4. For the rst time, activate the screen mirroring
function on your iPhone, iPad, or Mac and
choose the TV’s name you want to connect in the
searching list.
5. If an AirPlay passcode appears on your TV screen,
enter the passcode on your iOS or iPadOS device.
EN 15
English
Using more of your TV
6. To stop mirroring your iOS or iPadOS device, open
Control Center, tap screen mirroring, then tap stop
mirroring.
Notes:
-If your WiFi is turned o, press on the remote
control, select Settings > Network and Internet
> Wi-Fi, and press OK to turn it on.
-To disable the feature, select Settings > System
> AirPlay and HomeKit Settings > Apple
AirPlay and HomeKit > AirPlay and press OK
to turn it o.
-Apple, AirPlay, HomeKit and Siri are trademarks
of Apple Inc., registered in the U.S. and other
countries and regions.
-To use AirPlay and HomeKit with this Smart TV
Pro, the latest version of iOS, iPadOS, or macOS
is recommended.
Multi Visual
Allows you to enjoy dierent programmes with your
family on one TV at the same time.
The multi visual function is enabled by default. To use
the function, make sure your phone is Android OS
and the WiFi on the phone is turned on. Then follow
the steps below to operate.
1. Press on the remote control, select Settings >
Network and Internet > Wi-Fi, and press OK to
turn it on.
2. Press on the remote control,select Multi Visual,
then select your desired display mode and press
OK to connect.
3. Activate the cast screen function on your phone
and choose the TV’s name you want to connect in
the searching list.
4. For the rst time, depending on dierent types of
phones, there are two situations:
- An invitation prompt appears, select Accept and
press OK to connect.
- Enter a correct PIN code to connect as per the
PIN message on the phone.
5. To exit the multi visual function, press , then
select OK and press OK to conrm.
Notes:
-This feature is not available in any of the cases
below:
• when TV is using Netix or Media Player.
• if the video from phone/DTV is scrambled.
• when the capacity of required video decoding
exceeds 4K 60Hz.
-When in full screen mode, due to the
compatibility of the third party’s Apps, there might
occur failure to return to the dual views.
-Multiple phones can be used. When in dual view
mode, use / to move the focus to TV view and
then cast another phone to the TV.
-To check all available history list, press on
the remote control, select Settings > System
> Multi visual settings > Connection list and
press OK to enter.
Blue Light Filter
It reduces the amount of blue light emitted by
the screen, which can reduce the visual fatigue
associated with screen viewing.
1. Press on the remote control to display the
dashboard, select Picture > Advanced settings >
Colour and press OK/ to enter.
2. Select the Blue Light Filter option, and press OK to
toggle between on or o.
Notes:
-After watching TV for half an hour, please move
away from the TV and rest your eyes.
-When resting, please look far away to adjust the
ciliary muscles of the eye to avoid eye strain.
-Please form a good habit of doing eye exercises
to protect eyesight and prevent myopia.
EN 16
English
Chapter 5 - Other information
Password in Parental Control
- Set the password in the Settings > System > Lock
menu.
- The super password is 0423. If you forget your
code, enter the super password to override any
existing codes.
Troubleshooting
Please check the following list before requesting
service.
There is no picture or sound.
• Make sure the power cord is properly inserted in the
power outlet.
• Make sure the source type is set correctly.
• Make sure the antenna is properly connected.
• Make sure the volume is not set to minimum or the
sound is not set to mute.
• Make sure the headphones are not connected.
• The TV may be receiving a signal other than from
TV broadcasting stations.
Picture is not clear.
• Make sure the antenna cable is properly connected.
• Consider whether your TV signal is being properly
received.
• Poor picture quality can occur due to a VHS
camera, camcorder, or other peripheral being
connected at the same time. Switch o one of the
other peripherals.
• The ‘ghost’ or double image may be caused by
obstruction to the antenna due to high-rise buildings
or hills. Using a highly directional antenna may
improve the picture quality.
• The horizontal dotted lines shown on the pictures
may be caused by electrical interference, e.g., hair
dryer, nearby neon lights, etc. Turn o or remove
these.
Picture is too dark, too light or tinted.
• Check the colour adjustment.
• Check the brightness setting.
• Check the sharpness function.
Remote control does not work.
• Check the batteries of the remote control.
• Make sure the remote sensor window on the TV
front is not under strong uorescent lighting.
• Try to clean the remote sensor window on the TV
front with a soft cloth.
If the above suggestions do not solve your technical
issue, please refer to the warranty card for service
information.
Operating Conditions
Temperature 5°C – 35°C (41°F – 95°F)
Humidity 20 – 75% (non-condensing)
Storage Conditions
Temperature -15°C – 45°C (5°F – 113°F)
Humidity 10 – 90% (non-condensing)
Radio Information
• Bluetooth® transmitter frequency range:
2402 – 2480MHz
• Bluetooth® transmitter power: 6dBm (+/-4dB)
• 2.4G Wi-Fi transmitter frequency range:
2412 – 2472MHz
• 2.4G Wi-Fi transmitter power: 14dBm (+/-2dB)
• 5G Wi-Fi transmitter frequency range:
- Band 1: 5150 – 5250MHz
- Band 2: 5250 – 5350MHz
- Band 3: 5470 – 5725MHz
- Band 4: 5725 – 5850MHz
• 5G Wi-Fi transmitter power: 14dBm (+/-2dB)
• DVB-T/T2/C tuner frequency range: 50.5 – 858MHz
• DVB-S/S2 tuner frequency range: 950 – 2150MHz
* Operation of 5150 – 5350MHz is restricted to indoor
use only.
BE BG CZ DK DE EE IE
EL ES FR HR IT CY LV
LT LU HU MT NL AT PL
PT RO SI SK FI SE UK (NI)
OSS Notice
This product uses the GPL (Version 2 and 3) and
LGPL (version 2.1) and MPL (version 1.1).
To send inquiries and requests for questions
regarding open source, contact nearest TCL oce.
This product uses some software programs which are
distributed under the Independent JPEG Group.
This product uses some software programs which are
distributed under the libpng Project.
This product uses some software programs which are
distributed under the Freetype Project.
This product uses some software programs which are
distributed under the zlib Project.
This product uses some software programs (libxml2,
curl, expat, c-areas) which are distributed under the
MIT.
This product uses CyberLink for C which is distributed
under the Open Source Project.
This product uses opensl, xerces which is distributed
under the Apach License Project.
EN 17
English
Other information
GPL software: Linux Kernel, glib, libiconv, gcc libgcc,
gcc libstdc++, u-Boot loader, mepg, util-linux-ng,
e2fsprogs, wget, iptables
LGPL software: DFB (DirectFB), gstreamer, gst-
plugins-base, gst-plugins-good, gst-plugins-bad, gst-
plugins-ugly, gst-mpeg, glibc, wpa_supplicant
BSD software: webp, mng, uriparser
GNU software: dosfstools
[Legal Statement] of TCL - manufacturer of this
TV set
Due to the various capabilities of products featuring
the SmartTV - Services, as well as limitations in the
available content, certain features, applications, and
services may not be available on all devices or in
all territories. Some features on SmartTV may also
require additional peripheral devices or membership
fees that are sold separately. Please visit our website
for more information on specic device information
and content availability. The services and availability
of content through SmartTV are subject to change
from time to time without prior notice.
All content and services accessible through this
device belong to third parties and are protected by
copyright, patent, trademark and/or other intellectual
property laws. Such content and services are
provided solely for your personal noncommercial use.
You may not use any content or services in a manner
that has not been authorized by the content owner
or service provider. Without limiting the foregoing,
unless expressly authorized by the applicable content
owner or service provider, you may not modify, copy,
republish, upload, post, transmit, translate, sell, create
derivative works, exploit, or distribute in any manner
or medium any content or services displayed through
this device.
YOU EXPRESSLY ACKNOWLEDGE AND AGREE
THAT USE OF THE DEVICE IS AT YOUR SOLE
RISK AND THAT THE ENTIRE RISK AS TO
SATISFACTORY QUALITY, PERFORMANCE
AND ACCURACY IS WITH YOU. THE DEVICE
AND ALL THIRD PARTY CONTENT AND
SERVICES ARE PROVIDED “AS IS” WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED. TCL EXPRESSLY DISCLAIMS
ALL WARRANTIES AND CONDITIONS WITH
RESPECT TO THE DEVICE AND ANY CONTENT
AND SERVICES, EITHER EXPRESS OR,
IMPLIED, INCLUDING BUT NOT LIMITED TO,
WARRANTIES OF MERCHANTABILITY, OF
SATISFACTORY QUALITY, FITNESS FOR A
PARTICULAR PURPOSE, OF ACCURACY, OF
QUIET ENJOYMENT, AND NON-INFRINGEMENT
OF THIRD PARTY RIGHTS. TCL DOES NOT
GUARANTEE THE ACCURACY, VALIDITY,
TIMELINESS, LEGALITY, OR COMPLETENESS OF
ANY CONTENT OR SERVICE MADE AVAILABLE
THROUGH THIS DEVICE AND DOES NOT
WARRANT THAT THE DEVICE, CONTENT OR
SERVICES WILL MEET YOUR REQUIREMENTS,
OR THAT OPERATION OF THE DEVICE OR
SERVICES WILL BE UNINTERRUPTED OR
ERROR-FREE. UNDER NO CIRCUMSTANCES,
INCLUDING NEGLIGENCE, SHALL TCL BE LIABLE,
WHETHER IN CONTRACT OR TORT, FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR
CONSEQUENTIAL DAMAGES, ATTORNEY FEES,
EXPENSES, OR ANY OTHER DAMAGES ARISING
OUT OF, OR IN CONNECTION WITH, ANY
INFORMATION CONTAINED IN, OR AS A RESULT
OF THE USE OF THE DEVICE, OR ANY CONTENT
OR SERVICE ACCESSED BY YOU OR ANY THIRD
PARTY, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Third party services may be changed, suspended,
removed, terminated or interrupted, or access may be
disabled at any time, without notice, and TCL makes
no representation or warranty that any content or
service will remain available for any period of time.
Content and services are transmitted by third parties
by means of networks and transmission facilities
over which TCL has no control. Without limiting
the generality of this disclaimer, TCL expressly
disclaims any responsibility or liability for any change,
interruption, disabling, removal of or suspension
of any content or service made available through
this device. TCL may impose limits on the use of
or access to certain services or content, in any
case and without notice or liability. TCL is neither
responsible nor liable for customer service related to
the content and services. Any question or request for
service relating to the content or services should be
made directly to the respective content and service
providers.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
