AIRTOUCH 657232 User guide

657232
Brand
AIRTOUCH
Model
657232
Type
User guide
Liability and Disclaimer
All specications and procedures are correct at time of publication, but are subject to change without notice. Please read the
instructions before installing this Zone Control System. Polyaire Pty Ltd does not accept any responsibility for loss or damage
that may occur as a result of the incorrect installation or operation of this AirTouch Control System.
October 2021
© Polyaire Pty Ltd
The battery (3) used in the ITC is 3V CR2450.
When the battery is low, a
Low Battery
icon ( ) will appear near the
group name of the sensor. A good battery will last for around
1 ½ to 2 years.
When the battery is at, the group will change to % control if there is
no other sensor in it. The low battery sign will disappear from the group.
The group will then be treated as a group without a sensor.
When replacing the battery, press and hold the Pairing Button (2)
after removing the dead battery for 5 seconds to remove any residual
charge from the circuit.
2
1On the AirTouch console open the Quick Menu and select
System Settings > Installer > Sensors
Turn Sensor Pairing from Stop to Start.
By default, the installer password is Polyaire.
After removing the cover from the ITC sensor, push and
hold the Pairing Button (2) for 5 seconds until the LED (1)
turns blue (Zone On) or red (Zone O)
The group name will appear on the sensor page of
AirTouch 4 when the pairing is successful.
Repeat this process for all sensors in the same installation.
Select Stop on the Sensors Page after pairing all sensors.
The home screen will show both set points and
temperature control for the groups which have sensors
successfully assigned.
1
2
3
4
0
F
E
D
C
B
A
5
6
7
8
9
ON
1 2
ON
1 2
Status Blue Red Both at the
same time
Blue and Red
Alternate
On Solid - - -
O - Solid - -
On; Low
Battery
Flashing
Every 1s ---
O; Low
Battery -Flashing
Every 1s - -
Lost ---Flashing
Every 0.2s
Lost; Low
Battery --Flashing
Every 0.2s -
Not Paired ---Flashing
Every 1s
Not Paired;
Low Battery --Flashing
Every 1s -
• Tap once to see if a group is
ON (blue) or OFF (red).
• Tap again within 5 seconds to
switch the group ON or OFF.
On the Group Dial (4) for each ITC sensor,
select the correct group number to correspond
with the group that you are placing the sensor in.
Normally, 1 ITC sensor is assigned to 1 group, however, for larger
groups, 2 ITC sensors can be installed. This will require Dipswitch
(5) conguration as shown below:
ITC Motherboard Pairing ITC Sensors with AirTouch
Conguring
Individual Temperature Control (ITC) Sensors
Group Dial Conguration
Dipswitch Conguration
LED Indications
Dial Number 1 2 3 4 5 6 7 8 9
ITC paired
Group
Group
1
Group
2
Group
3
Group
4
Group
5
Group
6
Group
7
Group
8
Group
9
Dial Number A B C D E F 0
ITC paired
Group
Group
10
Group
11
Group
12
Group
13
Group
14
Group
15
Group
16
ON
1 2
Dipswitch setting
for one ITC Sensor
Dipswitch setting
for two ITC Sensors
Battery Replacement
Using ITC
Pairing Button (2)
ON/OFF
LED (1)
Dipswitch (5)
Group Dial (4)
Sensor A Sensor B
Group ON/OFF Switch
airtouch
PUSH
+_
Battery (3)
(push to remove)
Congure the
Group Dial
and
Dip Switches
before pairing the
sensor with AirTouch.
  • Page 1 1

AIRTOUCH 657232 User guide

657232
Brand
AIRTOUCH
Model
657232
Type
User guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents