2. Ingross
  3. 11671278830
11671278830

Ingross 11671278830 User manual

  • Hello, I've reviewed the user manual for the Honda CR-V's intake manifold removal and installation. It contains detailed steps, including instructions for disconnecting and connecting various hoses, sensors, and cables. I'm ready to help with any questions you have about the procedures outlined in the document.
  • What is the first step in removing the intake manifold?
    What should be done with the water bypass hoses before removing the intake manifold?
    What is the final step after installing the intake manifold?
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
1/16
Report a problem with this article
Intake Manifold Removal and Installation
Intake Manifold Removal and Installation
Exploded View
Removal
1. Removal the intake manifold cover.
2. Disconnect the intake air temperature (IAT) sensor connector (A), remove the breather hose (B), then remove
the air cleaner housing (C).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
2/16
3. Remove the throttle cover (A). Fully open the throttle link and cruise control link by hand, then remove the
throttle cable (B) and cruise control actuator cable (C) from the links. Loosen the locknuts (D), and remove the
cables from the bracket.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
3/16
4. Remove the evaporative emission (EVAP) canister hose (A) and brake booster vacuum hose (B).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
4/16
5. Remove the water bypass hoses, then plug the water bypass hoses.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
5/16
6. Disconnect the intake manifold runner control (IMRC) valve actuator control solenoid valve connector (A), then
remove the positive crankcase ventilation (PCV) hose (B) and IMRC valve control solenoid valve mounting bolt
(C).
7. Removal the bolt (A) securing the battery clamp, then remove the bulkhead cover (B).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
6/16
8. Remove the harness clamps.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
7/16
9. Remove the intake air duct mounting bolts (A) and upper bracket and cushion (B), then remove the bulkhead
(C).
10. Remove the engine wire harness connectors and wire harness clamps from the intake manifold.
Idle air control (IAC) valve connector
Throttle position sensor connector
Manifold absolute pressure (MAP) sensor connector
Evaporative emission (EVAP) canister purge valve connector
IMRC valve position sensor connector
11. Remove the intake manifold.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
8/16
Installation
1. Install the intake manifold (A), and tighten the bolts/nuts in a crisscross pattern in two or three steps, beginning
with the inner bolt. Use the new O-rings (B).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2F…
9/16
2. Install the bulkhead (A), then install the upper bracket and cushion (B) and intake air duct mounting bolts (C).
Apply body paint to the bulkhead mounting bolts.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
10/16
3. Connect the harness clamps.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
11/16
4. Install the bulkhead cover (A), then install the battery clamp bolt (B).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
12/16
5. Connect intake manifold runner control (IMRC) valve actuator control solenoid valve connector (A), then install
the positive crankcase ventilation (PCV) hose (B) and IMRC valve actuator control solenoid valve mounting bolt
(C).
6. Install the water bypass hoses.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
13/16
7. Install the evaporative emission (EVAP) canister hose (A) and brake booster vacuum hose(B).
8. Install the throttle cable, then adjust it.
9. Install the cruise control actuator cable, then adjust it.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
14/16
10. Install the air cleaner housing (A), and connect the intake air temperature (IAT) sensor connector (B).
11. Install the breather hose (C).
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
15/16
12. Install the intake manifold cover.
13. After installation, check that all tubes, hoses, and connectors are installed correctly.
14. Refill the radiator with engine coolant, and bleed air from the cooling system with the heater valve open.
15. Clean up any spilled engine coolant.
9/25/21, 11:33 PM
Intake Manifold Removal and Installation • 2006 Honda CR-V • MotoLogic
https://www.motologic.com/car/0b03fa60-3db7-012c-0340-19005f6e69db/article/4b7c1120-8956-012d-5df2-020000000101?returnPath=%2Fcar%2…
16/16
/