2. Computers & electronics
  3. Telecom & navigation
  4. Mobile phones
  5. Car kits
  6. Metra
  7. 95-5819
95-5819

Metra 95-5819 User manual

  • Hello! I am an AI chatbot trained to assist you with the Metra 95-5819 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
REV. 11/17/2020 INST95-5819
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
INSTALLATION INSTRUCTIONS FOR PART 95-5819
• A) Double DIN radio housing • B) Double DIN brackets
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-5520 - Ford 2003-up
Antenna Adapter:
• 40-CR10 - Chrysler 2002-up
• Cutting tool • Phillips screwdriver
• Socket wrench
TOOLS REQUIRED
A B
• Double DIN radio provision
KIT FEATURES
Ford F-150 2009-up (only XL models without plus package)
95-5819
2
Dash Disassembly
– Ford F-150 2009-up (only XL models without plus package) .................................. 2-3
Kit Assembly
– Double DIN radio provision ..................................................................................3
Table of Contents
1. Unclip and remove the switch
panel to the right of the cigarette
lighter then remove the (1) 9/32”
screw exposed. (Figure A)
2. Remove the rubber pad at the top
of the radio trim panel then remove
the (2) 9/32” screws exposed.
(Figure B)
3. Remove (4) 10 mm hex head
screws securing the factory radio.
Unplug wiring and remove radio.
Continue on next page
Ford F-150 2009-up
(only XL models without plus package)
(Figure B)
(Figure A)
95-5819 Dash Disassembly 95-5819
3
Dash Disassembly 95-5819
4. Unclip and pull the side panels
containing the A/C vents away
from the radio trim panel.
(Figure C)
Note: It is not necessary to remove
the panels completely.
5. Unclip and remove the radio trim
panel. (Figure D)
6. Remove (4) 9/32” screws to
remove the factory radio.
Continue to kit assembly
Ford F-150 2009-up
(only XL models without plus package) 1. Slide the appropriate side bracket
over the mounting legs of the
double DIN trim plate aligning the
holes in the trim plate and the
bracket and rotate inward.
Note: The notch in the housing
should be on top. (Figure A)
2. Slide the double DIN radio into the
bracket/radio housing assembly
and secure the double DIN radio
to the assembly using the screws
supplied with the radio. (Figure B)
Continue on back page
(Figure B)
Double DIN radio provision
(Figure A)
(Figure D)
(Figure C)
Kit Assembly 95-5819
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2004-2013 METRA ELECTRONICS CORPORATION
REV. 11/17/2020 INST95-5819
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
INSTALLATION INSTRUCTIONS FOR PART 95-5819
3. Cut and remove half of the
top (2) mounting legs with the
brackets attached. (Figure C)
4. Locate the factory wiring harness
in the dash. Metra recommends
using the proper mating adapter
from Metra or AXXESS. Re-connect
the negative battery terminal and
test the unit for proper operation.
5. Reassemble dash in reverse order
of disassembly.
(Figure C)
Double DIN radio provision
CUT HERE -
CUT HERE
TOP LEG ONLY
TOP LEG ONLY
CUT
CUT
Cut here - Top leg only
Cut here - Top leg only
Cut
Cut
/