Page is loading ...
16 PORT PoE SWITCH
QUICK START GUIDE
2
STEP 1
Connect the Q-SEE PoE
Switch via port 17 or 18
to your Router using an
Ethernet cable.
STEP 2
Connect your camera(s) to
one of the switch PoE Ports.
Your Router
Q-See PoE Switch
NOTE: Which port you
connect a camera to
will not matter. The first
camera connected will
be assigned to the first
available channel.
3
STEP 3
Right click the mouse on
the NVR and select Camera
Registration.
4
STEP 4
Click Search to update the list of cameras. The QCN8093B camera
and certain other camera models must be initialized before being
added when connecting to a PoE switch. If a camera is not initialized
it will appear with a Grey status icon. Select the check box for the
Camera(s) you wish to add.
5
STEP 5
Select Initialize.
6
STEP 6
Initialization will
apply the current
NVR password to
your cameras to
enhance security.
Click Next Step.
7
STEP 7
The IP Address
of your camera(s)
will be displayed.
Click Next Step.
STEP 8
Select Finished
once the
initialization is
completed.
8
STEP 9
Select the check box for the Camera(s) you wish to add to your
NVR. Click Add.
9
STEP 10
Cameras will appear once their status changes to Online.
WARRANTY & SUPPORT
Q-See is always here to answer your questions and take your valued
suggestions.
Visit us at www.q-see.com/support for 24/7 online
support and access to our Support Portal.
10
DISCLAIMER: Although Q-See has made every effort to ensure that the informa-
tion in this guide was correct at the time of printing, Q-See does not assume any
liability to any party for any loss, damage, or disruption caused by any errors,
omissions, or typos that may occur.
11
Regulatory Information
The regulatory information herein might vary according to the model you purchased. Some information is only applicable
for the country or region where the product is sold.
FCC Information: CAUTION: Changes or modifications not expressly approved by the party responsible for the compli-
ance could void the user’s authority to operate the equipment.
FCC Conditions: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Compliance: This equipment has been tested and found to comply with the limits or a digital device, pursuant to
part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to the radio communication.
For a class A device, these limits are designed to provide reasonable protection against harmful interference in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
For class B device, these limits are designed to provide reasonable protection against harmful interference in a residential
installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experience radio/TV technician for help.
SDOC Statement: www.Q-See.com/notices
Privacy Protection Notice: As the device user or data controller, you might collect personal data of others
such as face, fingerprints, car plate number, email address, phone number, GPS and so on. You need to be in compliance
with the local privacy protection laws and regulations to protect the legitimate rights and interests of other people by
implementing measures including but not limited to: providing clear and visible identification to inform data subject the
existence of surveillance area and providing related contact.
GQAPE16-E-V1
11/29/18, QAPE1601B
Phone Support
Mon-Fri : 6AM–7:00PM PST
1-877-998-3440
Chat Support
Mon-Fri: 6AM–7PM PST
Sat-Sun 9AM–5PM PST
24/7 Online Support Portal &
Knowledge Base
www.Q-See.com/support
/