SOFTWARE UPGRADE
After completed upgrading the following comes up in the display:
SOFTWARE UPGRADE
SUCCESSFUL UPGRADE!
YOU MAY NOW RESTART THE EQUIPMENT !
To make it possible to use the welding equipment, restart the welding power source by
S Turning the mains voltage switch for the power source to position 0.
S Turning the mains voltage switch to position 1.
For further information see programming manual.
För vidare information se programmeringsmanual.
For yderligere information se programmeringshandbog.
For ytterligere information se programmeringshåndbok.
Lisätietoja on ohjelmointikäsikirjassa.
Für weitere information sehen Sie Programmierungshandbuch.
Pour de plus amples informations voir de manuel de programmation.
Voor verder informatie zien handboek programmering.
Para la información adicional vea de manual de programación.
Per ulteriori informazioni vedere manuale di programmazione.
Para uma informação mais adicianal veja de manual de programação.
Rights reserved to alter specifications without notice.
0458 230 001
000925
1. INDICATE TOOL CODE
When upgrading the control box (weld data unit), all existing weld data will be deleted.
Do not forget to store the data on a PC--card before the upgrade procedure is started.
Make sure the mains voltage for the welding power source will not be disconnected in the
course of upgrading.
S Insert the PC--card containing the upgrading program.
S Turn the mains voltage switch on the welding power source to position 1.
The following display comes up.
CHOOSE CONNECTED TOOL:
PRB, PRC "
PRH
PRD
POC 12-- 60 mm
TIG HAND TORCH
A25
NEXT ENTER
S Move the marking using the soft key next. Choose the desired tool and press enter.
2. UPGRADE
S Press the MODE key to get to the auxiliary functions.
S Press the soft key software upgrade.
AUXIILIA RY FUNCTIONS
LANGUAGE "
ERROR LOG "
SHOW ACTUAL PARAMETER VALUES
SOFTWARE UPGRADE "
MJUKVARULÅS "
LAN --
GUAGE
ERROR
LOG
SHOW
PARA --
METER
SOFT
WARE
UPGR.
SOFT--
WARE
KEY
The following display comes up.
SOFTWARE UPGRADE
Unit Curr.ver PC--card
SYSTEM VERSION. 2.00A
BOOT SOFTWARE 1,12
j POWER SOURCE 1.50 2.00D
j ROT/WIRE UNIT 1.31A 1.40A
j WEAVE/AVC UNIT 1.31A 1.40A
j WELD DATA UNIT 2.11A 2.20A
NEXT
#
j
j
QUIT UP--
GRAADE
NOW
MENU EXPLANATION
SYSTEM VERSION Indicates the program version stored on the PC--card. A pro-
gram version can consist of 1--4 programs (1 for each unit).
BOOT SOFTWARE Program for upgrade handling.
POWER SOURCE PC--card for controlling the welding power source.
ROT/WIRE UNIT PC--card for controlling the rotation and wire feed motors.
WEAVE/AVC UNIT *) PC--card for controlling the weaving and AVC motors.
WELD DATA UNIT The PC--card in the control box.
(upgrades when changing language).
*) Only for LTP 450.
S Press the soft key next till you get to “power source”.
S Press the second soft key to mark the power source unit (gets ticked of f).
If further units are to be upgraded, they shall be marked in the same way .
By pressing the second soft key once again, the selection marked is cancelled (the marking
disappears).
SOFTWARE UPGRAD
unit Curr.ver PC--card
SYSTEM VERSION. 2.00A
BOOT SOFTWARE 1,12
j POWER SOURCE 1.50 2.00D
j ROT/WIRE UNIT 1.31A 1.40A
j WEAVE/AVC UNIT 1.31A 1.40A
j WELD DATA UNIT 2.11A 2.20A
NEXT
#
j
j
QUIT UP--
GRADE
NOW
S Press the soft key upgrade.
SOFTWARE UPGRADE
Unit Currt.ver PC--card
SYSTEM VERSION. 2,00A
BOOT SOFTWARE 1,12
j POWER SOFTWARE 1.50 2.00D
j ROT/WIRE UNIT 1.31A 1.40A
j WEAVE/AVC UNIT 1.31A 1.40A
j WELD DATA UNIT 2.11A 2.20A
NEXT
#
j
j
QUIT UP
GRADE
NOW
A dialogue box comes up in the display:
SOFTWARE UPGRADE
THE SOFTWARE UPGRADING CAN
TAKE UP TO 5 MIN/UNIT AND.
CANNOT BE INTERRUPTED!
DO YOU STILL WANT TO DO IT ?
NO YES
S Press the soft key yes for upgrading.
When upgrading the weld data unit the display is not moveable.
The following dialogue box comes up in the display while upgrading:
SOTWARE UPGRADE
DO NOT SWITCH OF THE EQUIPMENT
DURING THIS PROCESS!!
UPGRADING POWER SOURCE .....
UPGRADING POWER SOURCE .....
23% completed
kkkkkkkkkkkkkkkkk
-
1
-
2
ESAB LTP 450 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Epson Perfection 1650 PHOTO Scanner Product information
-
-
-
Epson 4490 - Perfection Photo Product information
-
-
-
Acer Altos R500 User manual
-
-
-