3M DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA Operating instructions

DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA
3M
Brand
3M
Model
DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA
Type
Operating instructions

This manual is also suitable for

1 1 8544096 GLIDERAIL ASSY6.5',JIB RAIL
2 2 8544100 WELDMENT,GUSSET,JIB SUPPORT,6.5'OFFSET
3 1 ---------- UPRIGHT ASSEMBLY
4 1 8545007 WELDMENT,BOLT,1-8X20.75,ZP,GR B7
5 2 8513789 WASHER,FLAT,1,W,ZP
6 1 8522156 NUT,LOCK,1,NYLONG
ITEM QTY PART NO. DESCRIPTION
COMPONENTS LIST
THIS DRAWING AND THE INFORMATION CONTAINED
HEREIN IS AND SHALL REMAIN THE PROPERTY OF
CAPITAL SAFETY, AND CANNOT BE USED OR
REPRODUCED WITHOUT PERMISSION. ANY MATERIAL
AND/OR PART SUBSTITUTIONS AND/OR CHANGES
MUST BE AUTHORIZED IN WRITING BY CAPITAL
SAFETY PRIOR TO USE.
Capital Safety
3833 SALA Way
RED WING, MN
55066-5005
651-388-8282
SCALE --------
PROE
www.capitalsafety.com
TITLE
EMU JIB ASSEMBLY
INSTRUCTION
DO NOT SCALE
DRAWING
DRAWING NUMBER REVISION
5903390 B
TOOLS REQUIRED
1-1/2 SOCKET AND WRENCH
1-1/8 SOCKET
1-1/16 WRENCH
3/4" SOCKET AND WRENCH
TORQUE WRENCH
ADJUSTABLE HEIGHT JIB ASSEMBLY
FOR MODEL #'S
8530557, 8530558, & 8530559
STEP 1 - UNCRATE AND IDENTIFY ALL OF THE
COMPONENTS IN THE COMPONENTS LIST.
STEP 2 - POSITION ITEM 3 ON ITS SIDE AND
SPACE IT OFF THE GROUND WITH A SPACER
AS SHOWN.
NOTE: ITEM 3 HAS A LIFTING
RING FOR POSITIONING VIA
CRANE OR FORKLIFT
STEP 3 - ATTACH ITEM 1 TO ITEM 3. FINGER
TIGHTEN HARDWARE. FINAL TIGHTENING
OF HARDWARE IN STEP 5.
STEP 4 - USE THE ITEM 2'S TO CONNECT THE ITEM 1
TO ITEM 3. FINGER TIGHTEN HARDWARE. FINAL
TIGHTENING OF HARDWARE IN STEP 5.
STEP 5 - FINAL TORQUE THE
CONNECTING HARDWARE TO
THE SPECIFICATIONS BELOW.
3.
1.
2.
4.
5.
6.
1.
3.
3/4" HARDWARE
3.
1.
4.
5.
5.
6.
2.
1/2" HARDWARE
130 ft*lbs [176 Nm]
60 ft*lbs [81 Nm]
175 ft*lbs [237 Nm]
THIS DRAWING AND THE INFORMATION CONTAINED
HEREIN IS AND SHALL REMAIN THE PROPERTY OF
CAPITAL SAFETY, AND CANNOT BE USED OR
REPRODUCED WITHOUT PERMISSION. ANY MATERIAL
AND/OR PART SUBSTITUTIONS AND/OR CHANGES
MUST BE AUTHORIZED IN WRITING BY CAPITAL
SAFETY PRIOR TO USE.
Capital Safety
3833 SALA Way
RED WING, MN
55066-5005
651-388-8282
SCALE --------
PROE
www.capitalsafety.com
TITLE
EMU JIB ASSEMBLY
INSTRUCTION
DO NOT SCALE
DRAWING
DRAWING NUMBER REVISION
5903390 B
TOOLS REQUIRED
3/4 SOCKET
3/4 WRENCH
TORQUE WRENCH
1 1 8545771 OFFSET ARM,ASSEMBLY,FIXED HEIGHT EMU
2 1 8545774 UPRIGHT,ASSEMBLY,FIXED HEIGHT EMU
ITEM QTY PART NO. DESCRIPTION
COMPONENTS LIST
2.
1.
1.
2.
FIXED HEIGHT JIB ASSEMBLY
FOR MODEL #'S
8530571
STEP 1 - UNCRATE AND IDENTIFY ALL OF THE
COMPONENTS IN THE COMPONENTS LIST.
STEP 2 - ATTACH ITEM 1 TO ITEM 2. TORQUE
ALL HARDWARE TO 60 FT*LBS [81 N*m].
SCALE 0.050
SEE DETAIL A
SEE DETAIL B
NOTE: ITEM 1 HAS A LIFTING
RING FOR POSITIONING VIA
CRANE OR FORKLIFT
DETAIL A
SCALE 0.250
4X 1/2" HARDWARE
  • Page 1 1
  • Page 2 2

3M DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA Operating instructions

DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA
3M
Brand
3M
Model
DBI-SALA® FlexiGuard™ Fixed Height Jib 8530571, Yellow and Silver, 21 ft. (6.4 m) anchor height, 1 EA
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents