USER’S MANUAL Anjan A-1008
DIAGRAM & FUNCTION INDICATION
INSTALL BATTERY
1. The radio uses two AAA batteries, please put the new batteries in the battery slot according to the
polarity.
2. If the sound is distorted or volume is faint, please change the batteries.
Attention :
1. Do not mix new and old batteries together.
2. In order to prevent the leakage of the electrolysis liquid or danger of explosion, do not charge, heat
or resolve the batteries.
3. If you do not use the radio for a long time, please take out the batteries.
USE EXTERNAL POWER
Please use output DC 3V 300mA regulating external direct current power , check the polarity. (adapter
not included)
TIME SETTING
1. The 24 hours system is used in the radio.
2. After installing batteries, under the clock mode, the “0:00” appears on LCD.
3. Under the time mode, press and hold the Time button. At the same time press the Hour or Min
buttons to adjust the hour and minute.
ALARM SET
1. Under the radio-off mode , keep and Alarm button pressed.
2. Press the Hour button to adjust hour and press the Min button to adjust the minute.
WAKE-TO-RADIO
1. Under the clock mode, press the Alarm button once , the symbol of a clock displays on the screen,
the wake-to-radio function begins to work. When the turn on time reaches, the radio will
automatically turn on to the last station.
2. Radio will turn off after one hour’s operation. Or you can press the Power or the Alarm button to
turn off the radio earlier.
3. Snooze function – After the radio is turned on by the wake-to-radio function, press the Snooze
button will suspend radio operation for 5 minutes.
SLEEP MODE
1. Press the Sleep button to enter into sleep mode , the default off time is 60 minutes .
2. You can press the Sleep button again to set the off time in the following order
60-50-40-30-20-10-cancel.
3. You can turn off the radio earlier by pressing the Power button.
POWER ON/OFF
1. Press Power button to turn the radio on and off.
2. Use the wake-to-radio function .
3. Time power-off (Sleep mode)
BAND SELECTION
1. Press the AM/FM button to switch between AM/FM band.
2. Use the Band Selector to switch between AM / SW1-8
STATION SEARCH
Adjust the Tuning Knob to search the required station.
Backlight
Press the Backlight button to turn on the backlight. The light will stay on for 8 seconds.
ANTENNA
1. The radio receives AM by using the internal magnetic antenna. You can get the best reception by
rotating the direction of the radio.
2. When you receive FM station, please pull out the telescopic antenna to get the best reception by
changing its length and angle.
3. When you receive SW station, please pull out the telescopic antenna and keep it vertical to get
better reception.
4. You can make use of the wiring antenna to improve the FM or SW reception.
TECHNICAL INDEX
1. Frequency Range :
o FM 76-108 MHz
o AM 525 - 1610 KHz
o SW 5.95 – 21.85 MHz
2. S.W Meter Band
o SW1 5.90-6.20 MHz SW5 13.60-13.80 MHz
o SW2 7.10-7.30 MHz SW6 15.10-15.60 MHz
o SW3 9.50-9.90 MHz SW7 17.55-17.90 MHz
o SW4 11.65 – 12.05 MHz SW8 21.45-21.85 MHz
3. Noise Limit Sensitivity
o FM ≦ 10uv
o AM ≦ 1mv/m
o SW ≦ 30uv
4. Single Signal Selectivity ≧ 20dB
5. Power : DC 3V or 2 x AAA batteries
6. Speaker : 45mm/16ohm/0.5W
7. Unit Size : 100 x 62 x 20 mm
8. Weight : 140g ( without battery)
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Roberts R871 User guide
-
Grundig G1100 User manual
-
Eton E1100 User manual
-
-
-
-
INTEK BCL-3000 Owner's manual
-
-
Silvercrest SWDR 500 B1 Operating Instructions And Safety Instructions
-
Sangean ATS-909X User manual