Runco PL-61DHD User manual

Category
Video converters
Type
User manual
OWNERS OPERATING MANUAL
PL-61DHD
Flat Panel Plasma Display Monitor
with
and
Digital High Definition
TM
Controller
with Vivix II
TM
Technology
Software Version 2.00
TM
Runco PlasmaWall Owner’s Operating Manual iii
PRE
L
IMINAR
Y
THREE YEAR LIMITED WARRANTY
For Plasma Displays
Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces
“The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of
unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your
other important documents.
SERVICE LABOR: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma
glass panel).
PARTS (not including plasma glass panel): Runco will provide new or rebuilt replacement parts for the parts that fail due to
defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such
replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.
PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Runco will
provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1)
year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the
remaining portion (if any) of the original warranty period.
Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is
the result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.
Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of
time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers
for this reason.
TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more
than a few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture
information is present on the left and right edges of the screen) are used as infrequently as possible. This will prevent
permanent image burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in
has occurred.
The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This
is why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after
being displayed continuously for an extended period of time).
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does
not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and
brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote
control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this
Limited Warranty.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
iv Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED
DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED
WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP
IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY.
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to
the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we
should discover a safety problem or product update for which you must be notified.
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Runco
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for
repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest
Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s
responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco
Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will
return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping
costs will be the responsibility of the owner.
© Copyright 2006 Runco International. This document contains proprietary information protected by copyright, trademark and
other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.
Reflection, Enhanced GEN3, DHD, Vivix, Virtual Cinema, CineWide, AutoScope, O-Path, CinOptx, LiveLink, CSMS, SuperOnyx
and VirtualWide are trademarks of Runco International. All other trademarks and registered trademarks used in this document
are the property of their respective owners.
Runco International products are manufactured under one or more of the following patents: US. Patent 6755540 and Other
Patents Pending.
RIGHTS, LIMITS AND EXCLUSIONS:
EFFECTIVE WARRANTY DATE:
IMPORTANT – WARRANTY REGISTRATION:
CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
COPYRIGHT AND TRADEMARKS:
Runco PlasmaWall Owner’s Operating Manual v
PRE
L
IMINAR
Y
To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this
Limited Warranty, please call or write:
RUNCO INTERNATIONAL, INC.
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777
Fax: (510) 324-9300
Toll Free: (800) 23-RUNCO
RUNCO VIDEO-PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
_________________________________________________________ ________________________________________
Model Purchased Date
____________________________________________________________________________________________________________
Serial Number
____________________________________________________________________________________________________________
Runco Authorized Dealer Name
____________________________________________________________________________________________________________
Address
____________________________________________ __________________ ________________________
City State/Province Postal Code
____________________________________________ _________________________________________________________
Phone Fax
ADDITIONAL INFORMATION:
vi Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
Thank you for your purchase of this quality Runco product! It has been designed to provide you with the quality of video that is
expected in a home theater. This manual is your guide through the menus and operation. For the best performance, please
read it carefully and keep it handy for future reference.
CAUTION
To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to
the equipment as possible, and should be easily accessible.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS
UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN
BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
This equipment has been tested and found to comply with the limits for a Class ‘B’ digital device, pursuant to Part 15 of FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the Installation Manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area may cause harmful interference, in which case the user will be required to correct the
interference at his own expense.
DOC Compliance Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no
injury will occur as a result of improper use.
Do not insert any object, especially metal or liquids, into the plasma display.
Do not place any objects containing water or any other liquid on top of the plasma display.
Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.
Do not install this system outdoors or otherwise exposed to the elements.
Do not place heavy objects on top of the plasma display.
If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the
power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way,
please contact your Runco Dealer for a replacement cord.
Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Runco
Dealer or Runco International for service. Removing the covers will void the warranty.
Safety Precautions
WARNING
This symbol is intended to alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Runco PlasmaWall Owner’s Operating Manual vii
1Table of Contents
PRE
L
IMINAR
Y
THREE YEAR LIMITED WARRANTY ............................................................................. iii
Safety Precautions ......................................................................................................... vi
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
Target Audience .....................................................................................................1
If You Have Comments About This Manual... ..........................................................1
Textual and Graphic Conventions ...........................................................................1
Using This Manual ........................................................................................................2
Description, Features and Benefits ...............................................................................3
Key Features and Benefits ......................................................................................3
Parts List ...............................................................................................................4
2. Controls and Functions ............................................................................................5
PlasmaWall at a Glance ................................................................................................5
Controls and Indicators...........................................................................................5
Connectors ............................................................................................................6
DHD Controller Front Panel ..........................................................................................8
DHD Controller Rear Panel .........................................................................................10
Outputs ................................................................................................................10
Inputs ...................................................................................................................10
DHD Controller Remote Control .................................................................................12
3. Installation ...............................................................................................................15
Remote Control ..........................................................................................................15
Notes on Batteries ................................................................................................15
Notes on Remote Control Operation.....................................................................15
Quick Setup ...............................................................................................................17
Installation Considerations ..........................................................................................18
Mounting the PlasmaWall on a Wall or Table Stand ..............................................18
Ambient Light .......................................................................................................18
Ventilation .............................................................................................................19
Other Considerations ............................................................................................19
Table of Contents
viii Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
Connections to the PlasmaWall and DHD Controller ...................................................20
Connecting the PlasmaWall to the DHD Controller ................................................20
Connecting Source Components to the DHD Controller .......................................22
RS-232 Controller Connection ..............................................................................26
Connecting 12-Volt Trigger Outputs to External Theater Components ..................26
Cable Management ..............................................................................................27
4. Operation .................................................................................................................29
Turning on the Power .................................................................................................29
Selecting the Input Source .........................................................................................30
Setting the PC Display Properties ...............................................................................30
Using the On-Screen Menus ......................................................................................32
Main Menu ...........................................................................................................34
Input Source ........................................................................................................34
Aspect Ratio ........................................................................................................34
Picture .................................................................................................................36
Input Position........................................................................................................39
ISF Presets ...........................................................................................................40
Information ...........................................................................................................40
Calibration ............................................................................................................41
Service .................................................................................................................42
5. Maintenance and Troubleshooting ........................................................................47
Troubleshooting Tips ..................................................................................................47
6. Serial Communications ..........................................................................................49
RS-232 Connection and Port Configuration ...............................................................49
Serial Command Syntax .............................................................................................49
7. Specifications ..........................................................................................................55
PlasmaWall Specifications ..........................................................................................55
DHD Controller Specifications ....................................................................................56
PlasmaWall Dimensions .............................................................................................57
Computer/Video Signal Compatibility .........................................................................58
Runco PlasmaWall Owner’s Operating Manual ix
1List of Figures
PRE
L
IMINAR
Y
2-1. PlasmaWall Front-Panel Controls and Indicators...........................................................5
2-2. PlasmaWall Connectors ...............................................................................................6
2-3. DHD Controller Front Panel ..........................................................................................8
2-4. DHD Controller Rear Panel .........................................................................................10
2-5. DHD Controller Remote Control .................................................................................12
3-1. Available Range of the Remote Control ......................................................................15
3-2. Ventilation Requirements for Enclosure Mounting .......................................................19
3-3. Connecting the PlasmaWall to the DHD Controller .....................................................20
3-4. RS-232 Connection from the DHD Controller to the PlasmaWall ................................21
3-5. DVI Source Connections ............................................................................................22
3-6. Digital (DTV) RGB Connections...................................................................................23
3-7. Analog RGB Connections...........................................................................................24
3-8. Composite, S-Video and Component Video Connections...........................................25
3-9. RS-232 Control System Connection...........................................................................26
3-10. Connecting 12-Volt Trigger Outputs .........................................................................26
3-11. Installing the Cable Clamps ......................................................................................27
4-1. Attaching the Ferrite Cores to the Power Cable ..........................................................29
4-2. DHD Controller OSD Menu Structure for PlasmaWall..................................................33
4-3. Typical PLUGE Pattern for Adjusting Brightness .........................................................36
4-4. Typical Gray Bar Pattern for Adjusting Contrast ..........................................................37
4-5. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................38
4-6. Typical Test Pattern for Adjusting Sharpness..............................................................39
7-1. PlasmaWall Model PL-61DHD Dimensions .................................................................57
List of Figures
x Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
Notes:
Runco PlasmaWall Owner’s Operating Manual 1
PRE
L
IMINAR
Y
1.1
About This Manual
This Owner’s Manual describes how to install, set up and operate the Runco PlasmaWall
Flat-Panel Plasma Display Monitor and DHD Controller (Model PL-61DHD). It describes
the features and functions available with DHD Controller Software version 2.0 and later.
Throughout this manual, the Runco PlasmaWall Flat-Panel Plasma Display Monitor and
DHD Controller are referred to collectively as the “PlasmaWall.”
Target AudienceRunco has prepared this manual to help home theater installers and end users get the
most out of the PlasmaWall.
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
may require updating from time to time. You can always find the latest version of this and
other Runco product manuals on-line, at www.runco.com.
If You Have Comments
About This Manual...
Runco welcomes your comments about this manual. Send them to techpub@runco.com.
Textual and Graphic
Conventions
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Remote control button identifiers are set in upper-case bold type; for example, “Press
EXIT to return to the previous menu.”
All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>, <Esc>
and <Tab>.
<Enter> indicates that you may press either the RETURN or ENTER key on your
computer keyboard if it has both keys.
Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Anamorphic, type ANAMORPHIC <Enter>.”
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
1. Introduction
A carriage return must be used after each command or string.
Note
Introduction
2 Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
1.2
Using This Manual
Use the following table to locate the specific information you need in this manual.
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
DANGER appears when a given action can cause severe injury or
death.
Tip
Note
Caution
WARNING
DANGER!
If you need... ... Turn to page:
Information about obtaining service iv
General information about the PlasmaWall
Flat-Panel Plasma Display Monitor and DHD Con-
troller
3
Installation instructions 15
First-time configuration instructions 30
Advanced configuration instructions 41
Troubleshooting tips 47
Specifications for the PlasmaWall Flat-Panel
Plasma Display Monitor and DHD Controller
55
Introduction
Runco PlasmaWall Owner’s Operating Manual 3
PRE
L
IMINAR
Y
1.3
Description, Features
and Benefits
The PlasmaWall™ is large enough to be used as the centerpiece of any home theater, yet
slim enough (less than five inches) to be used in any type of room environment. Its size is
only one of its advantages. It also has HDTV resolution of 1365 x 768, is bright enough to
be used in any lighting situation, and can be mounted on a wall or placed on a tabletop.
The PlasmaWall is supplied with Runco’s next-generation, all-digital DHD Controller,
featuring advanced Vivix II™ processing. This controller produces stunning video imagery,
elevating even standard NTSC material to near high-definition levels.
Multiple aspect ratio control includes Runco’s VirtualWide™ for viewing 4:3 material in
widescreen with no loss of picture quality. The DHD provides for a pure digital signal path
from input to output, making this system ready for Runco’s exclusive LiveLink™ DVI cable
solution to preserve HD signal quality over long runs.
The PlasmaWall has been skillfully engineered for the finest video performance at altitudes
of up to 9,000 feet. The advanced design features both RS-232C and IR control interfaces
to accommodate custom installation and everyday operation with ease.
Key Features and BenefitsThe PlasmaWall offers these key features and benefits:
Native Resolution: 1365 x 768 (16:9 Native Aspect Ratio)
Screen Size (diagonal): 61 inches
Multiple Aspect Ratios with VirtualWide™ Mode
Less than five inches deep
DVI Input with High-bandwidth Digital Content Protection (HDCP)
HDTV Compatible
Exceptional detail and artifact-free video enhancement
Vivix™ video processing with 3:2 film detection circuitry
Introduction
4 Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
Parts List Your PlasmaWall is shipped with the following items. If any items are missing or damaged,
please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.
PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller
AC Power Cords (2)
Remote Control Unit and two (2), AAA-size batteries
RJ-11 Telephone Cable, 50 feet (15.24 meters)
Serial Port Adapter, RJ-11 Female to DB-9 Female
Rack-mount hardware for the DHD Controller
Warranty information and registration card
Runco PlasmaWall Owner’s Operating Manual (this document)
Ferrite cores (2)
Cable Clamps
Safety metal fittings
Screws for safety metal fittings
Optional Accessories:
Wall Mount Kit
Table Stand
Use the safety fittings to fasten the PlasmaWall to a wall when using
the optional tablestand. This prevents tipping due to external
shock. Use the supplied screws to fasten the safety fittings to the
holes in the back of the plasma.
Note
Runco PlasmaWall Owner’s Operating Manual 5
PRE
L
IMINAR
Y
2.1
PlasmaWall at a
Glance
Figure 2-1 shows the locations of the PlasmaWall front-panel controls and indicators.
Controls and Indicators
Figure 2-1. PlasmaWall Front-Panel Controls and Indicators
1. POWER BUTTON
Turns the monitor’s power on and off.
2. REMOTE CONTROL SENSOR
Receives the signals from the remote control.
3. POWER/STANDBY INDICATOR
- Lights red to indicate that the PlasmaWall is in standby mode;
- Lights green to indicate normal operation;
- Flashes red to indicate that the internal temperature is too high.
2. Controls and Functions
MENU / ENTER
INPUT SELECT
DOWN UP LEFT/- RIGHT/+ /EXIT
VOLUME
4
5
6
7
1
Located on bottom
of Plasma
Located on bottom
of Plasma
3
2
Controls and Functions
6 Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
4. INPUT SELECT/EXIT
Not used with this model. Use the DHD Controller to select an input source.
5. LEFT/– and RIGHT/+
Not used with this model.
6. VOLUME DOWN and UP
Not used with this model.
7. MENU/ENTER
Not used with this model. Use the DHD Controller to access the on-screen menus.
Connectors Figure 2-2 shows the locations of the PlasmaWall connectors.
Figure 2-2. PlasmaWall Connectors
The Power on/off switch does not disconnect the plasma display
completely from the supply mains.
WARNING
AC IN
SPEAKER
R
+ -
L
- +
ANALOG RGB
(IN/OUT)
(IN/OUT)
(MONO)
R
L
YC
B/PB CR/PR R/CR/PR G/Y
(ON SYNC) (H/V SYNC)
B/CB/PB HD VD
VIDEO1
VIDEO2
VIDEO3
AUDIO1
(MONO)
R
L
AUDIO2
(MONO)
R
L
AUDIO3
RS-232C REMOTE
COMPONENT1 PC2/COMPONENT2 PC1
DIGITAL RGB
IN
3V 300mA
OUT
PC3
10
5
6
7
8
9
11
4
3
2
1
Controls and Functions
Runco PlasmaWall Owner’s Operating Manual 7
PRE
L
IMINAR
Y
1. POWER INPUT (100 to 240 VAC)
Connect the PlasmaWall to power here, using the included power cord.
2. EXTERNAL SPEAKER OUTPUTS
Not used. Connect speakers to an external audio amplifier/receiver.
3. VIDEO1, VIDEO2, VIDEO3 (BNC, RCA, S-Video)
Not used. Connect all video sources to the DHD Controller.
4. AUDIO1, AUDIO2, AUDIO3
Not used with this model. Connect the audio outputs from your sources to an external
audio receiver.
5. COMPONENT1
Not used. Connect all video sources to the DHD Controller.
6. PC2/COMPONENT2 (5xBNC)
Connect the RGBHV (5xBNC) output from the DHD Controller here.
7. PC1 (15-pin D-Sub)
Not used. Connect all video sources to the DHD Controller.
8. PC3 (DVI)
HDCP-compliant digital video input. Connect the DVI output from the DHD
Controller to this input.
9. RS-232C (9-pin, male D-Sub)
A male, 9-pin D-sub connector. Connect the RS-232 OUT port on the DHD
Controller to this input.
10. REMOTE IN (3.5-mm mini phone jack, tip/ring/sleeve)
Wired input (3.0 VDC/300 mA) from an external remote control or infrared (IR)
receiver.
11. REMOTE OUT (3.5-mm mini phone jack, tip/ring/sleeve)
Wired output to the REMOTE IN jack of another device; allows you to control both the
PlasmaWall and the other device using the same wired remote control.
Controls and Functions
8 Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
2.2
DHD Controller Front
Panel
Figure 2-3 shows the controls and indicators on the DHD Controller front panel; the
paragraphs that follow describe them.
Figure 2-3. DHD Controller Front Panel
1. RUNCO ICON
Lights red to indicate that the DHD Controller is in standby mode; lights blue to
indicate that the unit is on.
2. POWER BUTTON
Press once to toggle from standby mode to on mode. Press it again to return to
standby mode. For a discrete on or off command, you can use the direct access
buttons on the remote control.
3. IR SENSOR
Receives IR commands from the remote.
4. VACUUM FLUORESCENT DISPLAY
Can be used instead of the On-Screen Display (OSD). Displays currently-selected
menu or – if no menu is selected – the current source, signal format (NTSC or PAL),
input resolution and aspect ratio.
2
3
1
45
6
7
8
9
10
Controls and Functions
Runco PlasmaWall Owner’s Operating Manual 9
PRE
L
IMINAR
Y
5. UP BUTTON
Use to direct-select aspect ratios or move the menu cursor up in the On-Screen
Display. When no menus are present on-screen, the UP button toggles you through
aspect ratios in the following order:
Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema
(For more information about aspect ratios, refer to Table 4-1.)
6. LEFT BUTTON
Used to direct select inputs or move the menu cursor left in the On Screen Display.
When no menu is present on-screen, the LEFT button toggles you through the
different sources, in this order:
HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 -
Component SD - S-Video 2 - S-Video 1 - Composite
7. ENTER BUTTON
When an item is highlighted on the On-Screen Display, the ENTER button selects the
item.
8. DOWN BUTTON
Use to direct select aspect ratios or move the menu cursor down in the On-Screen
Display. When no menu is present on-screen, this button toggles you through the
different aspect ratios, in this order:
Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic
9. RIGHT BUTTON
Used to direct select inputs or move the menu cursor right in the On Screen Display.
When no menus are present on-screen, the RIGHT button toggles you through the
different sources, in this order:
Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1
- DVI
2 - HD Pass Thru 1 - HD Pass Thru 2
10. MENU BUTTON
Pressing the MENU button brings up the main menu. Also, if you are in an adjustment
mode or function, pressing MENU brings the menu back one level.
Controls and Functions
10 Runco PlasmaWall Owner’s Operating Manual
PRE
L
IMINAR
Y
2.3
DHD Controller Rear
Panel
Figure 2-4 shows the rear connector panel on the DHD Controller.
Figure 2-4. DHD Controller Rear Panel
Outputs 1. ANALOG OUTPUTS (RGBHV)
Connect these to the PC2/COMPONENT2 input of the PlasmaWall, using a
5
x BNC-to-5 x BNC breakout cable.
2. DVI OUT
Connect this to the PC3 (DIGITAL RGB) input on the PlasmaWall.
Inputs 3. DVI 1 / DVI 2 (Digital)
Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner
with a DVI or HDMI output.
4. HD1 / HD2 (Analog BNC connectors)
Five, BNC connectors for connecting either RGB or component high-definition
television signals. The PlasmaWall automatically detects the signal format: RGB(HV)
or YPrPb, 480p, 720p, 480i, 576i or 1080i.
5. COMPONENT VIDEO (RCA connectors)
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for
component video from sources such as DVD players.
Pb Pr Y
Video
3
IR
RS-232 Control
S-Video 1
S-Video 2
HD1
HD2
1
2
R/Pr G/Y B/Pb
R/Pr G/Y B/Pb H V
DVI 1 DVI 2DVI OutH/VVH
R/Pr G/Y B/Pb
HV
TRIGGERS
RS-232 Out
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE CENTER.
AVI S: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
WARNING:
TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
100-230VAC 50-60 Hz, 165 Watts Max
OUTPUTS
INPUTS
SYSTEM CONTROL INTERFACE
Component Video
SDI
Option
Serial No
Video Processor / Controller
Model
Runco International
Union City, CA
Made In USA
2
3
56
11 12 13 14
1
9
7
8
104
For best results, do not run your DVD player in progressive mode.
Tip
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Runco PL-61DHD User manual

Category
Video converters
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI