Runco PL-50XA User manual

OWNER’S OPERATING MANUAL

PL-50XA

PL-61DHD

Flat Panel Plasma Display Monitor

with

and

Digital High Definition

TM

Controller

with Vivix II

TM

Technology

TM

Runco PlasmaWall Owner’s Operating Manual iii

PRE

L

IMINAR

Y

THREE YEAR LIMITED WARRANTY

For Plasma Displays

Congratulations on your purchase of a Runco video product and welcome to the Runco family! We believe Runco produces

“The World’s Finest Home Theater Products.” With proper installation, setup and care, you should enjoy many years of

unparalleled video performance.

This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your

other important documents.

SERVICE LABOR: Runco will pay for service labor by Runco Authorized Service Center when needed as a result of a

manufacturing defect for a period of three (3) years from the effective date of delivery to the end user (excluding the plasma

glass panel).

PARTS (not including plasma glass panel): Runco will provide new or rebuilt replacement parts for the parts that fail due to

defects in materials or workmanship for a period of three (3) years from the effective date of delivery to the end user. Such

replacement parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.

PLASMA GLASS PANEL: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a

manufacturing defect for a period of one (1) year from the effective date of delivery to the end user. In addition, Runco will

provide new or rebuilt replacement parts for the parts that fail due to defects in materials or workmanship for a period of one (1)

year from the effective date of delivery to the end user. Such replacement parts are then subsequently warranted for the

remaining portion (if any) of the original warranty period.

Image burn-in on plasma display panels is specifically excluded from coverage under this Limited Warranty. Image burn-in is

the result of misuse of the product and therefore cannot be repaired under the terms of this Limited Warranty.

Normal viewing material such as television/satellite broadcasts, videotape or DVDs (not put into pause for extended periods of

time) will not cause damage to your display under normal conditions. Many DVD players are also equipped with screen savers

for this reason.

TO AVOID IMAGE RETENTION (Burn-in): Please ensure that still images are left on your plasma display panel for no more

than a few minutes. Also ensure that images displayed in the 4:3 aspect ratio mode (black or gray stripes, but no picture

information is present on the left and right edges of the screen) are used as infrequently as possible. This will prevent

permanent image burns on your plasma display panel, which can be seen permanently under certain conditions once burn-in

has occurred.

The types of images to avoid include video games, still images and computer screens with stationary tool bars and icons. (This

is why computers are equipped with screen savers – to prevent still images from burning into the monitor’s phosphors after

being displayed continuously for an extended period of time).

This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does

not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from

accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper

maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and

brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote

control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this

Limited Warranty.

WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:

iv Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

CAUTION: THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED

DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED

WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP

IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY.

Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There

are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to

the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and

some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or

exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from

state to state.

This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as

evidence of the purchase date.

Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we

should discover a safety problem or product update for which you must be notified.

Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of

the product, during usual working hours, providing location of product is within normal operating distance from a Runco

Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for

repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest

Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s

responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco

Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will

return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping

costs will be the responsibility of the owner.

reserved. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior

written permission of the manufacturer.

All trademarks and registered trademarks are the property of their respective owners.

RIGHTS, LIMITS AND EXCLUSIONS:

EFFECTIVE WARRANTY DATE:

IMPORTANT -- WARRANTY REGISTRATION:

CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:

COPYRIGHT AND TRADEMARKS:

Runco PlasmaWall Owner’s Operating Manual v

PRE

L

IMINAR

Y

To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this

Limited Warranty, please call or write:

RUNCO INTERNATIONAL, INC.

Attn: Customer Service Department

2900 Faber Street

Union City, CA 94587

Ph: (510) 324-7777

Fax: (510) 324-9300

Toll Free: (800) 23-RUNCO

RUNCO VIDEO-PRODUCT INFORMATION

RETAIN THIS INFORMATION FOR YOUR RECORDS

_________________________________________________________ ________________________________________

Model Purchased Date

____________________________________________________________________________________________________________

Serial Number

____________________________________________________________________________________________________________

Runco Authorized Dealer Name

____________________________________________________________________________________________________________

Address

____________________________________________ __________________ ________________________

City State/Province Postal Code

____________________________________________ _________________________________________________________

Phone Fax

ADDITIONAL INFORMATION:

vi Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

Thank you for your purchase of this quality Runco product! It has been designed to provide you with the quality of video that is

expected in a home theater. This manual is your guide through the menus and operation. For the best performance, please

read it carefully and keep it handy for future reference.

CAUTION

To turn off main power, be sure to remove the plugs from power outlets. The power outlet socket should be installed as near to

the equipment as possible, and should be easily accessible.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO NOT USE THIS

UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS, UNLESS THE PRONGS CAN

BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE COMPONENTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

This equipment has been tested and found to comply with the limits for a Class ‘B’ digital device, pursuant to Part 15 of FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated

in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the Installation Manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area may cause harmful interference, in which case the user will be required to correct the

interference at his own expense.

DOC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Please read and follow the safety precautions listed below to ensure the equipment is free from damage, and to ensure that no

injury will occur as a result of improper use.

• Do not insert any object, especially metal or liquids, into the plasma display.

• Do not place any objects containing water or any other liquid on top of the plasma display.

• Do not place the units in direct sunlight, near heaters or in extremely dusty or humid locations.

• Do not install this system outdoors or otherwise exposed to the elements.

• Do not place heavy objects on top of the plasma display.

• If the power cord is damaged or frayed in any way, electrical shock and/or fire may result. Do not place objects on the

power cord, and keep the cord away from heat-emitting devices. Should the power cord become damaged in any way,

please contact your Runco Dealer for a replacement cord.

• Do not remove the cover of the plasma display for any reason. If any problems arise with the unit, please contact a Runco

Dealer or Runco International for service. Removing the covers will void the warranty.

Safety Precautions

WARNING

This symbol is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock.

This symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Runco PlasmaWall Owner’s Operating Manual vii

1Table of Contents

PRE

L

IMINAR

Y

THREE YEAR LIMITED WARRANTY ............................................................................. iii

Safety Precautions ......................................................................................................... vi

1. Introduction ...............................................................................................................1

About This Manual .......................................................................................................1

Target Audience .....................................................................................................1

If You Have Comments About This Manual... ..........................................................1

Textual and Graphic Conventions ...........................................................................1

Using This Manual ........................................................................................................2

Description, Features and Benefits ...............................................................................3

Key Features and Benefits ......................................................................................3

Parts List ...............................................................................................................4

2. Controls and Functions ............................................................................................5

PlasmaWall at a Glance ................................................................................................5

Controls and Indicators...........................................................................................5

Connectors ............................................................................................................6

DHD Controller Front Panel ..........................................................................................8

DHD Controller Rear Panel .........................................................................................10

Outputs ................................................................................................................10

Inputs ...................................................................................................................10

DHD Controller Remote Control .................................................................................12

3. Installation ...............................................................................................................15

Remote Control ..........................................................................................................15

Notes on Batteries ................................................................................................15

Notes on Remote Control Operation.....................................................................15

Quick Setup ...............................................................................................................17

Installation Considerations ..........................................................................................18

Mounting the PlasmaWall on a Wall or Table Stand ..............................................18

Ambient Light .......................................................................................................18

Ventilation .............................................................................................................19

Other Considerations ............................................................................................19

Table of Contents

viii Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

Connections to the PlasmaWall and DHD Controller ...................................................20

Connecting the PlasmaWall to the DHD Controller ................................................20

Connecting Source Components to the DHD Controller .......................................22

RS-232 Controller Connection ..............................................................................26

Connecting 12-Volt Trigger Outputs to External Theater Components ..................26

Cable Management ..............................................................................................27

4. Operation .................................................................................................................29

Turning on the Power .................................................................................................29

Changing the OSD Language .....................................................................................30

Setting the PC Display Properties ...............................................................................30

Using the On-Screen Menus ......................................................................................31

Main Menu ...........................................................................................................33

Input Source ........................................................................................................33

Aspect Ratio ........................................................................................................33

Picture .................................................................................................................35

Input Position........................................................................................................38

ISF Presets ...........................................................................................................39

Information ...........................................................................................................39

Calibration ............................................................................................................39

Service .................................................................................................................41

5. Maintenance and Troubleshooting ........................................................................45

Troubleshooting Tips ..................................................................................................45

6. Serial Communications ..........................................................................................47

RS-232 Connection and Port Configuration ...............................................................47

Serial Command Syntax .............................................................................................47

7. Specifications ..........................................................................................................51

PlasmaWall Specifications ..........................................................................................51

DHD Controller Specifications ....................................................................................52

PlasmaWall Dimensions .............................................................................................53

Computer/Video Signal Compatibility .........................................................................55

Runco PlasmaWall Owner’s Operating Manual ix

1List of Figures

PRE

L

IMINAR

Y

2-1. PlasmaWall Controls and Indicators .............................................................................5

2-2. PlasmaWall Connectors ...............................................................................................6

2-3. DHD Controller Front Panel ..........................................................................................8

2-4. DHD Controller Rear Panel .........................................................................................10

2-5. DHD Controller Remote Control .................................................................................12

3-1. Available Range of the Remote Control ......................................................................15

3-2. Ventilation Requirements for Enclosure Mounting .......................................................19

3-3. Connecting the PlasmaWall to the DHD Controller .....................................................20

3-4. RS-232 Connection from the DHD Controller to the PlasmaWall ................................21

3-5. DVI Source Connections ............................................................................................22

3-6. Digital (DTV) RGB Connections...................................................................................23

3-7. Analog RGB Connections...........................................................................................24

3-8. Composite, S-Video and Component Video Connections...........................................25

3-9. RS-232 Control System Connection...........................................................................26

3-10. Connecting 12-Volt Trigger Outputs .........................................................................26

3-11. Installing the Cable Clamps ......................................................................................27

4-1. Attaching the Ferrite Cores to the Power Cable ..........................................................29

4-2. DHD Controller OSD Menu Structure for PlasmaWall..................................................32

4-3. Typical PLUGE Pattern for Adjusting Brightness .........................................................35

4-4. Typical Gray Bar Pattern for Adjusting Contrast ..........................................................36

4-5. Typical Color Bar Pattern for Adjusting Color Saturation and Tint................................37

4-6. Typical Test Pattern for Adjusting Sharpness..............................................................38

7-1. PlasmaWall Model PL-50XA Dimensions ....................................................................53

7-2. PlasmaWall Model PL-61DHD Dimensions .................................................................54

List of Figures

x Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

Runco PlasmaWall Owner’s Operating Manual 1

PRE

L

IMINAR

Y

1.1

About This Manual

This Owner’s Manual describes how to install, set up and operate the Runco PlasmaWall

Flat-Panel Plasma Display Monitor and DHD Controller (Models PL-50XA and PL-61DHD).

Throughout this manual, the Runco PlasmaWall Flat-Panel Plasma Display Monitor is

referred to simply as the “PlasmaWall.”

Target AudienceRunco has prepared this manual to help home theater installers and end users get the

most out of the PlasmaWall.

Runco has made every effort to ensure that this manual is accurate as of the date it was

printed. However, because of ongoing product improvements and customer feedback, it

may require updating from time to time. You can always find the latest version of this and

other Runco product manuals on-line, at www.runco.com.

If You Have Comments

About This Manual...

Runco welcomes your comments about this manual. Send them to techpub@runco.com.

Textual and Graphic

Conventions

Text Conventions: The following conventions are used in this manual, in order to clarify

the information and instructions provided:

• Remote control button identifiers are set in upper-case bold type; for example, “Press

EXIT to return to the previous menu.”

• All keys with functional names are initial-capped, set in bold type and enclosed in angle

brackets. These keys are the following: <Return>, <Spacebar>, <Control>, <Esc>

and <Tab>.

• <Return> indicates that you may press either the RETURN or ENTER key on your

computer keyboard if it has both keys.

• Computer input (commands you type) and output (responses that appear on-screen) is

shown in monospace (fixed-width) type; for example: “To change the aspect ratio to

Anamorphic, type ANAMORPHIC <Return>.”

In addition to these conventions, underlining, boldface and/or italics are occasionally used

to highlight important information, as in this example:

1. Introduction

A carriage return must be used after each command or string.

Note

Introduction

2 Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

Graphic Conventions: These symbols appear in numerous places throughout the

manual, to emphasize points that you must keep in mind to avoid problems with your

equipment or injury:

1.2

Using This Manual

Use the following table to locate the specific information you need in this manual.

TIPS highlight time-saving short cuts and helpful guidelines for using

certain features.

NOTES emphasize text with unusual importance or special

significance. They also provide supplemental information.

CAUTIONS alert users that a given action or omitted action can

degrade performance or cause a malfunction.

WARNINGS appear when a given action or omitted action can result

in damage to the equipment, or possible non-fatal injury to the user.

DANGER appears when a given action can cause severe injury or

death.

Tip

Note

Caution

WARNING

DANGER!

If you need... ... Turn to page:

Information about obtaining service iv

General information about the PlasmaWall

Flat-Panel Plasma Display Monitor and DHD Con-

troller

3

Installation instructions 15

First-time configuration instructions 30

Advanced configuration instructions 39

Troubleshooting tips 45

Specifications for the PlasmaWall Flat-Panel

Plasma Display Monitor and DHD Controller

51

Introduction

Runco PlasmaWall Owner’s Operating Manual 3

PRE

L

IMINAR

Y

1.3

Description, Features

and Benefits

The PlasmaWall™ is large enough to be used as the centerpiece of any home theater, yet

slim enough (less than five inches) to be used in any type of room environment. Its size is

only one of its advantages. It also has HDTV resolution of 1365 x 768, is bright enough to

be used in any lighting situation, and can be mounted on a wall or placed on a tabletop.

The PlasmaWall is supplied with Runco’s next-generation, all-digital DHD Controller,

featuring advanced Vivix II™ processing. This controller produces stunning video imagery,

elevating even standard NTSC material to near high-definition levels.

Multiple aspect ratio control includes Runco’s VirtualWide™ for viewing 4:3 material in

widescreen with no loss of picture quality. The DHD provides for a pure digital signal path

from input to output, making this system ready for Runco’s exclusive LiveLink™ DVI cable

solution to preserve HD signal quality over long runs.

The PlasmaWall has been skillfully engineered for the finest video performance at altitudes

of up to 9,000 feet. The advanced design features both RS-232C and IR control interfaces

to accommodate custom installation and everyday operation with ease.

Key Features and BenefitsThe PlasmaWall offers these key features and benefits:

• Native Resolution: 1365 x 768 (16:9 Native Aspect Ratio)

• Screen Size (diagonal): PL-50XA = 50 inches; PL-61DHD = 61 inches

• Multiple Aspect Ratios with VirtualWide™ Mode

• Less than five inches deep

• Dual HDMI Inputs with High-bandwidth Digital Content Protection (HDCP)

• HDTV Compatible

• Exceptional detail and artifact-free video enhancement

• Vivix™ video processing with 3:2 film detection circuitry

Introduction

4 Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

Parts List Your PlasmaWall is shipped with the following items. If any items are missing or damaged,

please contact your Runco dealer or Runco Customer Service at (800) 23-RUNCO.

• PlasmaWall Flat-Panel Plasma Display Monitor and DHD Controller

• AC Power Cords (2)

• Remote Control Unit and two (2), AAA-size batteries

• Warranty information and registration card

• Runco PlasmaWall Owner’s Operating Manual (this document)

• Ferrite cores (2)

• Cable Clamps

• Safety metal fittings

• Screws for safety metal fittings

Optional Accessories:

• Wall Mount Kit

• Table Stand

➤

Use the safety fittings to fasten the PlasmaWall to a wall when using

the optional tablestand. This prevents tipping due to external

shock. Use the supplied screws to fasten the safety fittings to the

holes in the back of the plasma.

Note

Runco PlasmaWall Owner’s Operating Manual 5

PRE

L

IMINAR

Y

2.1

PlasmaWall at a

Glance

Figure 2-1 and Figure 2-2 show the locations of the PlasmaWall controls, indicators and

connectors.

Controls and Indicators

Figure 2-1. PlasmaWall Controls and Indicators

1. POWER BUTTON

Turns the monitor’s power on and off.

2. REMOTE CONTROL SENSOR

Receives the signals from the remote control.

3. POWER/STANDBY INDICATOR

- Lights red to indicate that the PlasmaWall is in standby mode;

- Lights green to indicate normal operation;

- Flashes red to indicate that the internal temperature is too high.

2. Controls and Functions

MENU / ENTER

INPUT SELECT

DOWN UP LEFT/- RIGHT/+ /EXIT

VOLUME

4

5

6

7

1

Located on bottom

of Plasma

Located on bottom

of Plasma

3

2

Controls and Functions

6 Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

4. INPUT SELECT/EXIT

Not used with this model. Use the DHD Controller to select an input source.

5. LEFT/– and RIGHT/+

Not used with this model.

6. VOLUME DOWN and UP

Not used with this model.

7. MENU/ENTER

Not used with this model. Use the DHD Controller to access the on-screen menus.

Connectors

Figure 2-2. PlasmaWall Connectors

The Power on/off switch does not disconnect the plasma display

completely from the supply mains.

WARNING

➤

AC IN

RIGHT

+ -

LEFT

- +

5

6

7

8

10

9

4

3

2

1

Controls and Functions

Runco PlasmaWall Owner’s Operating Manual 7

PRE

L

IMINAR

Y

1. POWER INPUT (100 to 240 VAC)

Connect the PlasmaWall to power here, using the included power cord.

2. EXTERNAL SPEAKER OUTPUTS

Not used. Connect speakers to an external audio amplifier/receiver.

3. VIDEO1, 2 (RCA, S-Video)

Not used. Connect all video sources to the DHD Controller.

4. AUDIO1, AUDIO2, AUDIO3

Not used with this model. Connect the audio outputs from your sources to an external

audio receiver.

5. DVD/HD1

DVD/HD2

Not used. Connect all video sources to the DHD Controller.

6. PC/RGB (15-pin D-Sub)

Connect the RGBHV (5xBNC) output from the DHD Controller here.

7. DVD/HD3, DVD/HD4 (HDMI)

HDCP-compliant digital video inputs. Connect the DVI output from the DHD Controller

to the DVD/HD3 input. (DVD/HD4 is not used.)

8. EXTERNAL CONTROL (9-pin, male D-Sub)

A male, 9-pin D-sub connector. Connect the RS-232 OUT port on the DHD Controller

to this input.

9. REMOTE IN (3.5-mm mini phone jack, tip/ring/sleeve)

Wired input from an external remote control or infrared (IR) receiver.

10. REMOTE OUT (3.5-mm mini phone jack, tip/ring/sleeve)

Wired output to the REMOTE IN jack of another device; allows you to control both the

PlasmaWall and the other device using the same wired remote control.

Controls and Functions

8 Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

2.2

DHD Controller Front

Panel

Figure 2-3 shows the controls and indicators on the DHD Controller front panel; the

paragraphs that follow describe them.

Figure 2-3. DHD Controller Front Panel

1. RUNCO ICON

Lights red to indicate that the DHD Controller is in standby mode; lights blue to

indicate that the unit is on.

2. POWER BUTTON

Press once to toggle from standby mode to on mode. Press it again to return to

standby mode. For a discrete on or off command, you can use the direct access

buttons on the remote control.

3. IR SENSOR

Receives IR commands from the remote.

4. VACUUM FLUORESCENT DISPLAY

Can be used instead of the On-Screen Display (OSD). Displays currently-selected

menu or -- if no menu is selected -- the current source, signal format (NTSC or PAL),

input resolution and aspect ratio.

2

3

1

45

6

7

8

9

10

Controls and Functions

Runco PlasmaWall Owner’s Operating Manual 9

PRE

L

IMINAR

Y

5. UP BUTTON

Use to direct-select aspect ratios or move the menu cursor up in the On-Screen

Display. When no menus are present on-screen, the UP button toggles you through

aspect ratios in the following order:

Anamorphic - Standard (4:3) - Letterbox - VirtualWide - Cinema

(For more information about aspect ratios, refer to Table 4-1.)

6. LEFT BUTTON

Used to direct select inputs or move the menu cursor left in the On Screen Display.

When no menu is present on-screen, the LEFT button toggles you through the

different sources, in this order:

HD Pass Thru 2 - HD Pass Thru 1 - DVI 2 - DVI 1 - HD/RGB2 - HD/RGB1 -

Component SD - S-Video 2 - S-Video 1 - Composite

7. ENTER BUTTON

When an item is highlighted on the On-Screen Display, the ENTER button selects the

item.

8. DOWN BUTTON

Use to direct select aspect ratios or move the menu cursor down in the On-Screen

Display. When no menu is present on-screen, this button toggles you through the

different aspect ratios, in this order:

Cinema - VirtualWide - Letterbox - Standard (4:3) - Anamorphic

9. RIGHT BUTTON

Used to direct select inputs or move the menu cursor right in the On Screen Display.

When no menus are present on-screen, the RIGHT button toggles you through the

different sources, in this order:

Composite - S-Video 1 - S-Video 2 - Component SD - HD/RGB 1 - HD/RGB 2 - DVI 1

- DVI

2 - HD Pass Thru 1 - HD Pass Thru 2

10. MENU BUTTON

Pressing the MENU button brings up the main menu. Also, if you are in an adjustment

mode or function, pressing MENU brings the menu back one level.

Controls and Functions

10 Runco PlasmaWall Owner’s Operating Manual

PRE

L

IMINAR

Y

2.3

DHD Controller Rear

Panel

Figure 2-4 shows the rear connector panel on the DHD Controller.

Figure 2-4. DHD Controller Rear Panel

Outputs 1. ANALOG OUTPUTS (RGBHV)

Connect these to the PC/RGB input of the PlasmaWall, using a DB15HD-to-5 x BNC

breakout cable.

2. DVI OUT

Connect this to the DVD/HD3 input on the PlasmaWall, using a DVI-to-HDMI cable.

Inputs 3. DVI 1 / DVI 2 (Digital)

Two, HDCP-compliant digital video inputs for connecting a DVD player or HD tuner

with a DVI or HDMI output.

4. HD1 / HD2 (Analog BNC connectors)

Five, BNC connectors for connecting either RGB or component high-definition

television signals. The PlasmaWall automatically detects the signal format: RGB(HV)

or YPrPb, 480p, 720p, 480i, 576i or 1080i.

5. COMPONENT VIDEO (RCA connectors)

Standard Definition (480i/576i) Component (YPrPb) input. This is the input for

component video from sources such as DVD players.

Pb Pr Y

Video

3

IR

RS-232 Control

S-Video 1

S-Video 2

HD1

HD2

1

2

R/Pr G/Y B/Pb

R/Pr G/Y B/Pb H V

DVI 1 DVI 2DVI OutH/VVH

R/Pr G/Y B/Pb

HV

TRIGGERS

RS-232 Out

CAUTION:

TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE CENTER.

AVI S: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

!

WARNING:

TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

100-230VAC 50-60 Hz, 165 Watts Max

OUTPUTS

INPUTS

SYSTEM CONTROL INTERFACE

Component Video

SDI

Option

Serial No

Video Processor / Controller

Model

Runco International

Union City, CA

Made In USA

2 3 5 6 11 12 13 14

810

1

4

97

➤

For best results, do not run your DVD player in progressive mode.

Tip

Page is loading ...

Runco PL-50XA User manual

This manual is also suitable for

Runco PL-50XA User manual

Related papers

Other documents